Categories for: springs
Springs - Compression - Conical
Conical 302 Stainless steel springs
Solid height lower than a standard compression spring due to the conical shape. Ends are closed. Starting rate is the same as the kg/mm rate.
Drawbar springs have long steel loops that pass through the centre of the spring and hook around the opposite end, compressing the spring on loading.
This design helps prevent unexpected overloading and fracturing that can occur in standard extension springs by stopping and hold the load at the spring limit. The spring rate indicates the load required to pull out the first 25mm of the spring.
Washers - Disc Spring - Carbon Steel
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093.
Washers - Disc Spring - Plastic
Also known as belleville washers.
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb® material.
Washers - Disc Spring - Stainless Steel
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093.
Anchors - Spring - Stainless Steel
An economical way to secure the ends of extension springs, and provide easy adjustment.
300 Grade Stainless Steel.
An economical way to secure the ends of extension springs, and provide easy adjustment.
C-12114 Steel with Black Oxide Finsh.
Spring Motor Assemblies - Open - RINO
Budget Assemblies. Average fatigue life of 5000 to 30000 cycles.
Springs : 301 Stainless Steel. Average fatigue life of 5,000 to 30,000 cycles.
Base Mounted.
Base Mounted. Springs : 301 Stainless Steel.
Temp Range: -70 to 175 Deg C (-94 to 347 Deg F). Vibration dampening
Lateral to vertical stiffness approx. 1:1 / Must be loaded vertically through its axis. Elastic limit corresponds to a maximum load in compression of 1.2 g (0.042oz) and radially 0.2 g (0.007oz). Damping factor c/co 0.15 to 0.20. Base Plate: Mild Steel / Springs: High Tensile Steel - Phosphated and dyed black. Isolator: Knitted stainless steel mesh / End Caps: Light Alloy.
Stainless Steel or Plastic - No Thread.
Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.
Plungers - Spring - Striker Bushings
Use with ball or bolt spring plungers for a hard wearing contact area.
Burnished ground hardened steel.
Includes ball plungers and pin plungers
Items shown with Long-Lok have a dry threadlocking sealant applied to thread.
Wire - Steel - Spring - Music Wire
SAE 1090 Spring Steel.
Shipped in straight lengths on wood backing board.
Stainless steel pads for corrosive environments. Vibration dampening
Natural frequency 15 to 25 Hz vertical, 12 to 20 Hz radial. Mechanical resistance is equal to 10G of continuous acceleration.
Mounts - Spring - Eliptical Leaf - Heavy Duty
Nato approved naval XM mounts
304 Stainless leaves, nylon and stainless washers and stainless steel mesh damping compound. For extreme environments and conditions. Temperature range -150 Deg C to + 400 Deg C.
Mounts - Spring - Eliptical Leaf - Light Duty
Lightweight NATO approved X Mounts
The 6kg mount is designed to isolate lightweight equipment like computers, printers, electronics panels etc from shock and vibration. All vibration modes and stiffness indicated are for mounting on a flat horizontal surface where vertical indicates the downwards stiffness and horizontal indicates stiffness alonf the horizontal plane. Horizontal 2 figures are for inverted mounting. 304 Stainless leaves, nylon and stainless washers and polymer damping compound. Temperature range +10 Deg C to + 30 Deg C.
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Shim - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
Ball Buttons - Stainless Steel
Used as a detent for ball plungers or similar applications. Made from hardened 440C Stainless Steel.
Ball Transfer Units - Spring Loaded - Flanged
For conveying materials. From miniature to large.
Case: Zinc plated Mild Steel. Ball: Carbon Steel 60-66 HRC. Applications: - Guillotines - Presses - Moulding machines - Base of machines for easy handling - Press brakes - Shock loading.
Ball Transfer Units - Spring Loaded - Unflanged
For conveying materials. From miniature to large.
Case: Zinc plated Mild Steel. Ball: Carbon Steel 60-66 HRC. Applications: - Guillotines - Presses - Moulding machines - Base of machines for easy handling - Press brakes - Shock loading.
Joints - Clevis - Spring Clips
Made from 9SMn steel.
Steel 9 SMn 28K (550-700 N/mm2). See also yokes.
Washers - Lock - Internal Tooth - Spring Steel
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
Snap Buttons - Single End - Spring Leg
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
Couplings - Slip - Spring Wrapped
Tension control - transmission overload protection. 0.035 to 1.69 Nm.
Coupling is sliped over one shaft and screws tightened. Second shaft is inserted into other end. Loose end of coupling is pulled back about 0.5mm then screws tightened. Serves as a torque limiter as well as a coupling. Long life under continuous slip applications.
Reels - Spring Powered - Arbor Mounted
Mounting studs sold seperately.
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture. Mounting studs sold seperately.
Damps low frequency vibrations.
Studs: Steel / Body : Silicone Gel / Spring : Piano Wire Type B Nickel Plated. Vertical vibrations damped without horizontal deflection. Compression only. Outstanding shock absorbing ability.
Collars - Shaft - Gripfast - 304 Stainless Steel
Self Locking - Quick Release.
304 Stainless Body, Retention Ring, Balls and Springs.
Circlips - External - Inverted
N1408 / SHI / 16626 / 4100 / 5108 - Spring Steel and Stainless Steel.
Tapered section ring with lugs inverted on the ID to allow use in tight areas with minimal clearance. Less thrust load than standard circlips.
Spiral Rings - External - Heavy Duty
AHE / WSM / AS3216 / RSN / MIL-R-27426A2 - Spring Steel and Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHE, Smalley: WSM, Spirolox and Ramsey: RSN, Aerospace: AS3216, MIL-R-27426A2.
Spiral Rings - External - Light Duty
Includes series CE / VS / US - Spring Steel and Stainless Steel.
Light duty single turn rings used in low clearance applications. Also used as a positioning point for light loads. Radius notch on one end for removal. Narrow radial wall yields moderate thrust loads. Equivalent to Associated Spring: CE, Smalley: VS, Spirolox and Ramsey: US.
Spiral Rings - External - Medium Duty
AE / WS / AS3218 / RS / MIL-R-27426A1 - Spring Steel and Stainless Steel.
Popular series that will accommodate light and medium bearing series thrust loads. Available in military and aerospace specifications. Equivalent to Associated Spring: AE, Smalley: WS, Spirolox and Ramsey: RS, Aerospace AS3218, MIL-R-27426A1.
Spiral Rings - External - Medium/Heavy Duty
AME / WST / RST - Spring Steel and Stainless Steel.
Originally designed to fit NAS50-51 grooves, this series is a popular OEM specification. This two/three turn design is easier to install than the heavy duty RRN option. Equivalent to Associated Spring: AME, Smalley: WST, Spirolox and Ramsey: RST.
Spiral Rings - Internal - Heavy Duty
Includes AHI / WHM / AS3215 / Spirolox RRN / MIL-R-27426B2 - Spring Steel and Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHI, Smalley: WHM, Spirolox and Ramsey: RRN, Aerospace AS3215, MIL-R-27426B2.Too many choices?
You have selected to see ALL categories including any of the following words: springs
Click here to see ONLY THE MOST POPULAR categories including any of the following words: springs
|
| |||||||||||||||||||||||||
| Select all items starting with... | |||||||||||||||||||||||||
| A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | Or use the category search | ||||||||||||||||
|
| |||||||||||||||||||||||||
