Categories for: spring wire
Wire - Steel - Spring - Music Wire
SAE 1090 Spring Steel.
Shipped in straight lengths on wood backing board.
Wire - Steel - Brass
Brass
Shipped in straight lengths on wood backing board.
Springs - Compression - Metre Lengths
Music wire to Din 17223 Class C. No. 1,1200. Stainless Steel wire to Din 17224 No. 1,4310.
Springs - Extension - Metre Lengths
Music wire to Din 17223 Class C. No. 1,1200. Stainless Steel wire to Din 17224 No. 1,4310.
Plungers - Spring - Smooth
Stainless Steel or Plastic - No Thread.
Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.
Plungers - Spring - Striker Bushings
Use with ball or bolt spring plungers for a hard wearing contact area.
Burnished ground hardened steel.
Plungers - Spring - Threaded
Includes ball plungers and pin plungers
Items shown with Long-Lok have a dry threadlocking sealant applied to thread.
Plungers - Spring - Threaded - With Limit Switch
Supply Cable : Grey Two Phase for normally open contacts, black for normally closed. Temp (Body): -40 deg C to 170 deg C Temp (Cable): -10 deg C to 50 deg C. Electrical Supply : 20 mA DC / 50 mA DC. Voltage : 24V Supply Cable 2.8mm - 2 Phase. Safety Standard : IP40 Average Switch Life Span : 56 Switching.
Washers - Disc Spring - Carbon Steel
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093.
Washers - Disc Spring - Plastic
Also known as belleville washers.
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb® material.
Washers - Disc Spring - Stainless Steel
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093.
Washers - Spring
Wave Washers - All Materials.
Springs - Compression - Conical
Conical 302 Stainless steel springs
Solid height lower than a standard compression spring due to the conical shape. Ends are closed. Starting rate is the same as the kg/mm rate.
Springs - Compression - Standard
Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote.
Springs - Drawbar
Drawbar springs have long steel loops that pass through the centre of the spring and hook around the opposite end, compressing the spring on loading.
This design helps prevent unexpected overloading and fracturing that can occur in standard extension springs by stopping and hold the load at the spring limit. The spring rate indicates the load required to pull out the first 25mm of the spring.
Springs - Constant Force
Mounting hole specifications will be supplied on request. Free ID may vary to meet load specification.
Springs - Die
High tensile strength chromium alloy steels. Heat Resistance: Up to +230°C (Loss of load occurs above +120°C). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length.
Springs - Extension
Zinc Plated Spring Steel not recommended for applications exceeding 121 Deg C (250 Deg F). 302 Stainless springs not recommended for applications exceeding 260 Deg C (500 Deg F). 302 stainless steel is slightly magnetic.
Gas Springs - Adjustable - 50-540N
Body: Semi Matt Black Epoxy Paint. Finish: Black. Adjusted by Grubscrew. Once discharged, the gas is not refillable. Supplied filled to maximum force.
Gas Springs - Adjustable - Accessories
See diagrams in main Gas Springs Categories.
Gas Springs - Adjustable - Push Type - Max 100N
Piston Rod: Hard black ceramic finish. Body: Powder Coated. End Fittings: Zinc Plated Steel. Operating Temp. Range: -20°C to +80°C End Position Damping Length: Approx. 5mm. Available Force Range: 5N to 100N (comes standard with max. force).
Gas Springs - Adjustable - Push Type - Max 1300N
Piston Rod: Hard black ceramic finish. Body: Powder Coated. End Fittings: Zinc Plated Steel. Operating Temp. Range: -20°C to +80°C End Position Damping Length: Approx. 10mm. Available Force Range: 80N to 1300N (comes standard with max. force).
Gas Springs - Adjustable - Push Type - Max 180N
Piston Rod: Hard black ceramic finish. Body: Powder Coated. End Fittings: Zinc Plated Steel. Operating Temp. Range: -20°C to +80°C End Position Damping Length: Approx. 10mm. Available Force Range: 10N to 180N (comes standard with max. force).
Gas Springs - Adjustable - Push Type - Max 2600N
Piston Rod: Hard black ceramic finish. Body: Powder Coated. End Fittings: Zinc Plated Steel. Operating Temp. Range: -20°C to +80°C End Position Damping Length: Approx. 10mm. Available Force Range: 100N to 2600N (comes standard with max. force).
Gas Springs - Adjustable - Push Type - Max 400N
Piston Rod: Hard black ceramic finish. Body: Powder Coated. End Fittings: Zinc Plated Steel. Operating Temp. Range: -20°C to +80°C End Position Damping Length: Approx. 10mm. Available Force Range: 10N to 400N (comes standard with max. force).
Gas Springs - Adjustable - Push Type - Max 5000N
Piston Rod: Hard black ceramic finish. Body: Powder Coated. End Fittings: Zinc Plated Steel. Operating Temp. Range: -20°C to +80°C End Position Damping Length: Approx. 10mm. Available Force Range: 500N to 5000N (comes standard with max. force).
Gas Springs - Adjustable - Push Type - Max 700N
Piston Rod: Hard black ceramic finish. Body: Powder Coated. End Fittings: Zinc Plated Steel. Operating Temp. Range: -20°C to +80°C End Position Damping Length: Approx. 10mm. Available Force Range: 50N to 700N (comes standard with max. force).
Anchors - Spring - Stainless Steel
An economical way to secure the ends of extension springs, and provide easy adjustment.
300 Grade Stainless Steel.
Anchors - Spring - Steel
An economical way to secure the ends of extension springs, and provide easy adjustment.
C-12114 Steel with Black Oxide Finsh.
Spring Assemblies - Bracket - RINO
Spring: Stainless Steel 301 S21 Grade. Bobbin and Bracket: Nylon Moulded secured to aluminium sheet. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring. End holes are centred at the distances and diameters shown in the tables.
Spring Assemblies - Single - RINO
Spring: Stainless Steel 301 S21 Grade. Other Parts: Pressed Mild Steel, Zinc Plate and clear passivated. Temp Max 200 Deg C / Min -200 Deg C. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring.
Spring Assemblies - Small Bracket - RINO
Spring: Stainless Steel 301 S21 Grade. Base: Aluminium Drum: High Impact Styrine. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring.
Spring Assemblies - Twin - RINO
Spring: Stainless Steel 301 S21 Grade. Other Parts: Pressed Mild Steel, Zinc Plate and clear passivated. Temp Max 200 Deg C / Min -200 Deg C. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring.
Spring Motor Assemblies - Open - RINO
Budget Assemblies. Average fatigue life of 5000 to 30000 cycles.
Springs : 301 Stainless Steel. Average fatigue life of 5,000 to 30,000 cycles.
Spring Motor Assemblies - SDP
Base Mounted.
Base Mounted. Springs : 301 Stainless Steel.
Spring Motors - RINO
301 stainless Steel. Shipped as shown to be mounted on drums (not supplied) of the recommended diameters. Torque ratings listed are for the unwinding portion of the cycle. Torque at fully wound end of cycle will be slightly higher.
Spring Motors - SDP
301 stainless Steel. Shipped as shown to be mounted on drums (not supplied) of the recommended diameters. Torque ratings listed are for the unwinding portion of the cycle. Torque at fully wound end of cycle will be slightly higher.
Springs - Torsion - Left Hand Wound
Left Hand Wound. 180 Deg. Deflection. Right hand wound and special springs are available on special order.
Mounts - Spring - Damped
Temp Range: -70 to 175 Deg C (-94 to 347 Deg F). Vibration dampening
Lateral to vertical stiffness approx. 1:1 / Must be loaded vertically through its axis. Elastic limit corresponds to a maximum load in compression of 1.2 g (0.042oz) and radially 0.2 g (0.007oz). Damping factor c/co 0.15 to 0.20. Base Plate: Mild Steel / Springs: High Tensile Steel - Phosphated and dyed black. Isolator: Knitted stainless steel mesh / End Caps: Light Alloy.
Mounts - Spring and Pad
Stainless steel pads for corrosive environments. Vibration dampening
Natural frequency 15 to 25 Hz vertical, 12 to 20 Hz radial. Mechanical resistance is equal to 10G of continuous acceleration.
Mounts - Spring - Eliptical Leaf - Heavy Duty
Nato approved naval XM mounts
304 Stainless leaves, nylon and stainless washers and stainless steel mesh damping compound. For extreme environments and conditions. Temperature range -150 Deg C to + 400 Deg C.
Mounts - Spring - Eliptical Leaf - Light Duty
Lightweight NATO approved X Mounts
The 6kg mount is designed to isolate lightweight equipment like computers, printers, electronics panels etc from shock and vibration. All vibration modes and stiffness indicated are for mounting on a flat horizontal surface where vertical indicates the downwards stiffness and horizontal indicates stiffness alonf the horizontal plane. Horizontal 2 figures are for inverted mounting. 304 Stainless leaves, nylon and stainless washers and polymer damping compound. Temperature range +10 Deg C to + 30 Deg C.
Mounts - Spring - Suspension - Pedestal
Cadmium plated steel. Temp Range : -60 to 150 Deg C (-76 to 302 Deg F).
Mounts - Spring - Suspension - Single Hole
Cadmium plated steel. Temp Range : -60 to 150 Deg C (-76 to 302 Deg F).
Gears - Pinion Wire - 24 Pitch
Brass and carbon steel.
Metallic.
Gears - Pinion Wire - 32 Pitch
Brass and carbon steel.
Metallic.
Gears - Pinion Wire - 48 Pitch
Brass and carbon steel.
Metallic.
Gears - Pinion Wire - 64 Pitch
Brass and carbon steel.
Metallic.
Dampers - Spring - Silicone
Damps low frequency vibrations.
Studs: Steel / Body : Silicone Gel / Spring : Piano Wire Type B Nickel Plated. Vertical vibrations damped without horizontal deflection. Compression only. Outstanding shock absorbing ability.
Ball Transfer Units - Spring Loaded - Flanged
For conveying materials. From miniature to large.
Case: Zinc plated Mild Steel. Ball: Carbon Steel 60-66 HRC. Applications: - Guillotines - Presses - Moulding machines - Base of machines for easy handling - Press brakes - Shock loading.
Ball Transfer Units - Spring Loaded - Unflanged
For conveying materials. From miniature to large.
Case: Zinc plated Mild Steel. Ball: Carbon Steel 60-66 HRC. Applications: - Guillotines - Presses - Moulding machines - Base of machines for easy handling - Press brakes - Shock loading.
Joints - Clevis - Spring Clips
Made from 9SMn steel.
Steel 9 SMn 28K (550-700 N/mm2). See also yokes.
Washers - Lock - External Tooth - Spring Steel
Dimensions are nominal and may vary between batches.
Washers - Lock - Internal Tooth - Spring Steel
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
Snap Buttons - Single End - Spring Leg
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
Couplings - Slip - Spring Wrapped
Tension control - transmission overload protection. 0.035 to 1.69 Nm.
Coupling is sliped over one shaft and screws tightened. Second shaft is inserted into other end. Loose end of coupling is pulled back about 0.5mm then screws tightened. Serves as a torque limiter as well as a coupling. Long life under continuous slip applications.
Reels - Spring Powered - Arbor Mounted
Mounting studs sold seperately.
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture. Mounting studs sold seperately.
Reels - Spring Powered - Base Mounted - Plastic Case
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
Reels - Spring Powered - Base Mounted - Steel
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
Reels - Spring Powered - Bracket Mounted
Applications: Counterbalances, door closers, cable retractors. Applications: Hose retreivers, tool head returns, cabinets and furniture.
Indent Blocks
Indent Blocks: Hardened black oxide sintered steel. Used together with spring plungers for detenting or positioning sliding parts, flaps or for similar applications.
