All Items: Spring Mounts - Categories


Spring Mounts

Hide Pictures

Go to Top  


Mounts - Spring and Pad

Mounts - Spring and Pad

Stainless steel pads for corrosive environments. Vibration dampening

Natural frequency 15 to 25 Hz vertical, 12 to 20 Hz radial. Mechanical resistance is equal to 10G of continuous acceleration.

Mounts - Spring - Eliptical Leaf - Heavy Duty

Mounts - Spring - Eliptical Leaf - Heavy Duty

Nato approved naval XM mounts

304 Stainless leaves, nylon and stainless washers and stainless steel mesh damping compound. For extreme environments and conditions. Temperature range -150 oC to + 400 oC.

Click for combined categories: All Spring Mounts


Mounts - Spring - Eliptical Leaf - Light Duty

Mounts - Spring - Eliptical Leaf - Light Duty

Lightweight NATO approved X Mounts

The 6kg mount is designed to isolate lightweight equipment like computers, printers, electronics panels etc from shock and vibration. All vibration modes and stiffness indicated are for mounting on a flat horizontal surface where vertical indicates the downwards stiffness and horizontal indicates stiffness alonf the horizontal plane. Horizontal 2 figures are for inverted mounting. 304 Stainless leaves, nylon and stainless washers and polymer damping compound. Temperature range +10 oC to + 30 Deg C.

Click for combined categories: All Spring Mounts


Springs - Neoprene

Springs - Neoprene

Neoprene elastomer springs have proven to be the safest, most efficient material for punching, stamping and drawing dies.

Major advantages include high loads, increased durability, better performance, no maintenance and long life.

Click for combined categories: All Rubber Springs


Springs - Urethane

Springs - Urethane

Urethane springs are designed for use in applications where corrosion, vibration or magnetism prevent the use of conventional steel springs.

They replace steel coil springs in medium pressure applications involving space limitations, high blank holding pressure and adequate stripping. Durometer 95 shore A. Colour black. Tensile strength 5000 psi. Temperature range minus 40 to 80 oC.

Click for combined categories: All Rubber Springs


Spring Damped Mounts

Hide Pictures

Go to Top  


Mounts - Spring - Damped

Mounts - Spring - Damped

Temp Range: -70 to 175 Deg C (-94 to 347 Deg F). Vibration dampening

Lateral to vertical stiffness approx. 1:1 / Must be loaded vertically through its axis. Elastic limit corresponds to a maximum load in compression of 1.2 g (0.042oz) and radially 0.2 g (0.007oz). Damping factor c/co 0.15 to 0.20. Base Plate: Mild Steel / Springs: High Tensile Steel - Phosphated and dyed black. Isolator: Knitted stainless steel mesh / End Caps: Light Alloy.

Spring Reels

Hide Pictures

Go to Top  


Reels - Spring Powered - Arbor Mounted

Reels - Spring Powered - Arbor Mounted

Mounting studs sold seperately.

Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture. Mounting studs sold seperately.

Click for combined categories: All Reels

Related Information:
Arbor Mounting Stud


Reels - Spring Powered - Base Mounted - Plastic Case

Reels - Spring Powered - Base Mounted - Plastic Case

Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.

Click for combined categories: All Reels


Reels - Spring Powered - Base Mounted - Steel

Reels - Spring Powered - Base Mounted - Steel

Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.

Click for combined categories: All Reels


Reels - Spring Powered - Bracket Mounted

Reels - Spring Powered - Bracket Mounted

Applications: Counterbalances, door closers, cable retractors. Applications: Hose retreivers, tool head returns, cabinets and furniture.

Click for combined categories: All Reels


Spring Motors

Hide Pictures

Go to Top  


Spring Motor Assemblies - SDP

Spring Motor Assemblies - SDP

Base Mounted.

Base Mounted. Springs : 301 Stainless Steel.

Click for combined categories: All Spring Motors


Springs Constant Force

Hide Pictures

Go to Top  


Springs - Constant Force

Springs - Constant Force

301 Stainless Steel

Mounting hole specifications will be supplied on request. These springs are usually mounted on a drum and the free end attached to a loading force like a counterbalance. Free ID may vary to meet load specification. Load capacity can be increased by using multiple strips in tandem, back to back or laminated. Be sure to leave at least 40mm coiled on the drum at full extension. The spring ID will wrap tightly on the drum so that most applications require no fastening to the drum.

Plungers Indexing

Hide Pictures

Go to Top  


Plungers - Indexing - Locking - With Mounting Plate - Steel

Plungers - Indexing - Locking - With Mounting Plate - Steel

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Spring loaded to work in a variety of applications on both tooling and equipment that require surface mounting. Plunger is hardened and ground. Knob is black matte plastic. Mounting plate is zinc plated steel. Includes rest position for plunger to stay in retracted position.

Click for combined categories: All Indexing Plungers


Latches

Hide Pictures

Go to Top  


Latches - Paddle - Flush - Miniature - 304 Stainless

Latches - Paddle - Flush - Miniature - 304 Stainless

Flush mounting. Slide is plastic. Spring loaded paddle won't rattle. Smooth push to close latching. Quick one screw mounting. Max load 8.9kg.


Plungers Indexing

Hide Pictures

Go to Top  


Plungers - Indexing - Non Locking - With Mounting Plate - Steel

Plungers - Indexing - Non Locking - With Mounting Plate - Steel

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Spring loaded to work in a variety of applications on both tooling and equipment that require surface mounting. Plunger is hardened and ground. Knob is black matte plastic. Mounting plate is zinc plated steel.

Click for combined categories: All Indexing Plungers


Spring Motors

Hide Pictures

Go to Top  


Spring Motors - RINO

Spring Motors - RINO

301 stainless Steel. Shipped as shown to be mounted on drums (not supplied) of the recommended diameters. Torque ratings listed are for the unwinding portion of the cycle. Torque at fully wound end of cycle will be slightly higher.

Click for combined categories: All Spring Motors


Spring Motors - SDP

Spring Motors - SDP

301 stainless Steel. Shipped as shown to be mounted on drums (not supplied) of the recommended diameters. Torque ratings listed are for the unwinding portion of the cycle. Torque at fully wound end of cycle will be slightly higher.

Click for combined categories: All Spring Motors


Latches

Hide Pictures

Go to Top  


Latches - Pull - Flush - Locking

Latches - Pull - Flush - Locking

Low profile. Corrosion resistant. Simple 50.8mm (2 in.) round hole installation. Mounts in panels up to 22.2mm thick. M5 philips pan head mounting screws. Includes tab for inside actuation.

Max working load 26kg. Ultimate load 53kg. Black polycarbonate with stainless spring, keeper and screws.

Latches - Spring Loaded

Latches - Spring Loaded

Steel construction with either black enamel or chrome finish. 90o or straight mounting options. Keeper included.


Latches - Push to Close

Latches - Push to Close

Knob stores flush and pops out at a touch. Turn the knob to open and push to close. Latches securely with knob in or out.

Accomodates misalignment. Use on flush, surface mount or perpendicular doors. Quick 31.8mm Diameter round hole installation. Polycarbonate / ABS blended material with glass filled black nylon keepers, nut and pawl. Corrosion and UV resistant. Chrome plated with 304 stainless steel internal springs. Max working load 22kg. Available with serrated pawl for self adjusting grip or regular pawl for fixed grip. Keepers included. Keeper for fixed grip is stainless steel.

Latches - Snap Slide

Latches - Snap Slide

Used for attaching subplates and assemblies. The sliding bar is attached to the removable panel and the post is mounted to the stationary support.

In the closed position the spring action of the bar resists opening under vibration and shock load. The removable panel thickness must be between 1.2 and 4.0mm. Spacers may be needed and are included with each latch. The post can be attached with rivets, screw and nut or wood screw. Each comes with post and bar assembly. Made from zinc plated steel with chromate finish.

Dampers

Hide Pictures

Go to Top  


Dampers - Spring - Silicone

Dampers - Spring - Silicone

Damps low frequency vibrations.

Studs: Steel / Body : Silicone Gel / Spring : Piano Wire Type B Nickel Plated. Vertical vibrations damped without horizontal deflection. Compression only. Outstanding shock absorbing ability.

Click for combined categories: All Dampers


Ball Screws

Hide Pictures

Go to Top  


Mounts - Universal - For Acme Thread and Ball Screws

Mounts - Universal - For Acme Thread and Ball Screws

Use grade 8 hex socket head cap screws for mounting.


Air Springs

Hide Pictures

Go to Top  


Springs - Air - Convolute Bellows

Springs - Air - Convolute Bellows


Spring Assemblies

Hide Pictures

Go to Top  


Spring Assemblies - Bracket - RINO

Spring Assemblies - Bracket - RINO

Spring: Stainless Steel 301 S21 Grade. Bobbin and Bracket: Nylon Moulded secured to aluminium sheet. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring. End holes are centred at the distances and diameters shown in the tables.

Click for combined categories: All Spring Assemblies


Spring Assemblies - Single - RINO

Spring Assemblies - Single - RINO

Spring: Stainless Steel 301 S21 Grade. Other Parts: Pressed Mild Steel, Zinc Plate and clear passivated. Temp Max 200 oC / Min -200 oC. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring.

Click for combined categories: All Spring Assemblies


Spring Assemblies - Small Bracket - RINO

Spring Assemblies - Small Bracket - RINO

Spring: Stainless Steel 301 S21 Grade. Base: Aluminium Drum: High Impact Styrine. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring.

Click for combined categories: All Spring Assemblies


Spring Assemblies - Twin - RINO

Spring Assemblies - Twin - RINO

Spring: Stainless Steel 301 S21 Grade. Other Parts: Pressed Mild Steel, Zinc Plate and clear passivated. Temp Max 200 oC / Min -200 oC. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring.

Click for combined categories: All Spring Assemblies


Spring Motors

Hide Pictures

Go to Top  


Spring Motor Assemblies - Open - RINO

Spring Motor Assemblies - Open - RINO

Budget Assemblies. Average fatigue life of 5000 to 30000 cycles.

Springs : 301 Stainless Steel. Average fatigue life of 5,000 to 30,000 cycles.

Click for combined categories: All Spring Motors


Springs Anti Backlash

Hide Pictures

Go to Top  


Springs - Torsion - Anti Backlash

Springs - Torsion - Anti Backlash

Replacement springs for the mini-lash gears listed on this site.

The torsion spring is placed into c-bore of one of the Mini-lash Gears, and each of its tangs placed into appropriate drill of each of Mini-lash Gears. Then by turning one of them called Free Gear, we load torsion spring creating anti-backlash torque. Then when teeth on both gears are aligned we mate it with the opposing gear. In such a way there is no clearance in the gear mesh, and reversing direction of rotation doesn’t bring lost motion in the gear train. Transmitted torque shouldn’t exceed torsion spring preset torque.

Springs Compression

Hide Pictures

Go to Top  


Springs - Compression - Conical

Springs - Compression - Conical

Conical 302 Stainless steel springs

Solid height lower than a standard compression spring due to the conical shape. Ends are closed. Starting rate is the same as the kg/mm rate.

Click for combined categories: All Compression Springs


Springs - Compression - Long Lengths - Music Wire

Springs - Compression - Long Lengths - Music Wire

1 metre and 914mm lengths

Music wire to Din 17223 Class C. No. 1,1200. Stainless Steel wire to Din 17224 No. 1,4310.

Click for combined categories: All Compression Springs


Springs - Compression - Long Lengths - Stainless Steel

Springs - Compression - Long Lengths - Stainless Steel

1 metre and half metre lengths

Music wire to Din 17223 Class C. No. 1,1200. Stainless Steel wire to Din 17224 No. 1,4310.

Click for combined categories: All Compression Springs


Springs - Compression - Standard - Stainless Steel

Springs - Compression - Standard - Stainless Steel

Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote.

Click for combined categories: All Compression Springs

Related Information:
Zinc Plated Compression Springs


Springs - Compression - Standard - Steel

Springs - Compression - Standard - Steel

Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote.

Click for combined categories: All Compression Springs

Related Information:
Stainless Steel Compression Springs


Springs - Drawbar - Stainless Steel

Springs - Drawbar - Stainless Steel

Drawbar springs have long steel loops that pass through the centre of the spring and hook around the opposite end, compressing the spring on loading.

This design helps prevent unexpected overloading and fracturing that can occur in standard extension springs by stopping and hold the load at the spring limit. The spring rate indicates the load required to pull out the first 25mm of the spring.

Click for combined categories: All Drawbar Springs


Springs - Drawbar - Zinc Plated

Springs - Drawbar - Zinc Plated

Drawbar springs have long steel loops that pass through the centre of the spring and hook around the opposite end, compressing the spring on loading.

This design helps prevent unexpected overloading and fracturing that can occur in standard extension springs by stopping and hold the load at the spring limit. The spring rate indicates the load required to pull out the first 25mm of the spring.

Click for combined categories: All Drawbar Springs


Springs Die

Hide Pictures

Go to Top  


Springs - Die - Imperial - Extra Heavy Duty

Springs - Die - Imperial - Extra Heavy Duty

Vapor degassed high tensile strength chromium alloy steel. Spring ends are ground square. Designed for long life cycle with constant high end deflections and shot peened to increase fatigue life.

Colour coded green. Efficient operating range is 15 to 20 percent of the length. Maximum deflection is 25 percent of the length.

Click for combined categories: All Imperial Die Springs

Click for combined categories: All All Die Springs


Springs - Die - Imperial - Heavy Duty

Springs - Die - Imperial - Heavy Duty

Vapor degassed high tensile strength chromium alloy steel. Spring ends are ground square. Designed for long life cycle with constant high end deflections and shot peened to increase fatigue life.

Colour coded gold. Efficient operating range is 15 to 25 percent of the length. Maximum deflection is 30 percent of the length.

Click for combined categories: All Imperial Die Springs

Click for combined categories: All All Die Springs


Springs - Die - Imperial - Heavy Duty - Chrome Silicon

Springs - Die - Imperial - Heavy Duty - Chrome Silicon

Chrome silicon die springs are longer lasting than high carbon steel. Shot peened to reduce working stress and to improve the surface.

Colour coded gold. Efficient operating range is 15 to 20 percent of the length. Maximum deflection is 30 percent of the length.

Click for combined categories: All Imperial Die Springs

Click for combined categories: All All Die Springs


Springs - Die - Imperial - Medium Duty

Springs - Die - Imperial - Medium Duty

Vapor degassed high tensile strength chromium alloy steel. Spring ends are ground square. Designed for long life cycle with constant high end deflections and shot peened to increase fatigue life.

Colour coded blue. Efficient operating range is 25 to 40 percent of the length. Maximum deflection is 50 percent of the length.

Click for combined categories: All Imperial Die Springs

Click for combined categories: All All Die Springs


Springs - Die - Imperial - Medium Duty - Chrome Silicon

Springs - Die - Imperial - Medium Duty - Chrome Silicon

Chrome silicon die springs are longer lasting than high carbon steel. Shot peened to reduce working stress and to improve the surface.

Colour coded blue. Efficient operating range is 25 to 35 percent of the length. Maximum deflection is 50 percent of the length.

Click for combined categories: All Imperial Die Springs

Click for combined categories: All All Die Springs


Springs - Die - Imperial - Medium-Heavy Duty

Springs - Die - Imperial - Medium-Heavy Duty

Vapor degassed high tensile strength chromium alloy steel. Spring ends are ground square. Designed for long life cycle with constant high end deflections and shot peened to increase fatigue life.

Colour coded red. Efficient operating range is 20 to 30 percent of the length. Maximum deflection is 37 percent of the length.

Click for combined categories: All Imperial Die Springs

Click for combined categories: All All Die Springs


Springs - Die - Imperial - Medium Heavy Duty - Chrome Silicon

Springs - Die - Imperial - Medium Heavy Duty - Chrome Silicon

Chrome silicon die springs are longer lasting than high carbon steel. Shot peened to reduce working stress and to improve the surface.

Colour coded red. Efficient operating range is 20 to 25 percent of the length. Maximum deflection is 37 percent of the length.

Click for combined categories: All Imperial Die Springs

Click for combined categories: All All Die Springs


Springs - Die - Metric - Extra Heavy Duty

Springs - Die - Metric - Extra Heavy Duty

Colour coded yellow

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length.

Click for combined categories: All Metric Die Springs

Click for combined categories: All All Die Springs


Springs - Die - Metric - Heavy Duty

Springs - Die - Metric - Heavy Duty

Colour coded red

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length.

Click for combined categories: All Metric Die Springs

Click for combined categories: All All Die Springs


Springs - Die - Metric - Light Duty

Springs - Die - Metric - Light Duty

Colour coded green

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length.

Click for combined categories: All Metric Die Springs

Click for combined categories: All All Die Springs


Springs - Die - Metric - Medium Duty

Springs - Die - Metric - Medium Duty

Colour coded blue

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length.

Click for combined categories: All Metric Die Springs

Click for combined categories: All All Die Springs


Springs Extension

Hide Pictures

Go to Top  


Springs - Extension - Music Wire

Springs - Extension - Music Wire

Includes long lengths up to 1 metre

Zinc Plated Spring Steel not recommended for applications exceeding 121 oC (250 Deg F). 302 Stainless springs not recommended for applications exceeding 260 oC (500 Deg F). 302 stainless steel is slightly magnetic.

Click for combined categories: All Extension Springs


Springs - Extension - Stainless Steel

Springs - Extension - Stainless Steel

Includes long lengths up to 1 metre

Zinc Plated Spring Steel not recommended for applications exceeding 121 oC (250 Deg F). 302 Stainless springs not recommended for applications exceeding 260 oC (500 Deg F). 302 stainless steel is slightly magnetic.

Click for combined categories: All Extension Springs


Springs Torsion

Hide Pictures

Go to Top  


Springs - Torsion - Left Hand Wound

Springs - Torsion - Left Hand Wound

Free Deflection denotes the angle of the legs in the unloaded starting position

Load should be applied at about half the leg length.

Click for combined categories: All Torsion Springs


Springs - Torsion - Right Hand Wound

Springs - Torsion - Right Hand Wound

Free Deflection denotes the angle of the legs in the unloaded starting position

Load should be applied at about half the leg length.

Click for combined categories: All Torsion Springs


Isolators

Hide Pictures

Go to Top  


Mounts - Vibration - Isolation - Compression - Stainless Steel

Mounts - Vibration - Isolation - Compression - Stainless Steel

Compression shear mounts for harsh environments.

Excellent protection against shock vibration and noise4 in compression and shear applications. Developed especially for applications in harsh environments in food and pharmaceutical industries. High dampening characteristics. Stainless top plate is domed to guard against oil contamination. Low profile. Compact design. Elastomer insert is made from highly chemical resistant nitrile with good deflection properties. Concentric rings in the base of the insert firmly anchor machine to the floor.

Click for combined categories: All Base Mounts


Mounts - Vibration - Isolation - Cup Style 2

Mounts - Vibration - Isolation - Cup Style 2

Industrial cupmounts provide excellent protection against severe impact shock, vibration and noise.

High vibration dampening. Fail safe, rugged interlocking metal and neoprene construction. Metal cupmount is cold rolled steel. Low profile compact design. Metal top plate is domed shape to guard against oil contamination. High grade neoprene elastomer provides resistance to ozone and oils.

Click for combined categories: All Cup Mounts


Mounts - Vibration - Isolation Pads - Compression Shear

Mounts - Vibration - Isolation Pads - Compression Shear

Durable, high quality mount combines effective compression and shear isolation from vibration and shock with the convenience of an internal leveling device.

Deep cavity design allows excellent vibration and shock control in both the vertical and horizontal directions. Heavy duty ductile iron cover and chemically resistant neoprene insert. Internal leveling device levels up to 12.7mm. Specially designed recess on top of cover hosues a rubber washer. Concentric rings on base of neoprene insert prevents walking or creeping. Ideal for lathes, milling machines, punch presses, printing machines, shears, brakes, injection moulding machines, grinders etc. Includes all necessary hardware.

Click for combined categories: All Isolation Pad Mounts


Mounts - Vibration - Isolation Pads - General Purpose

Mounts - Vibration - Isolation Pads - General Purpose

For installation of industrial machinery where the ratio of shear loads to vertical loads is less than or equal to 1 to 5.

Base is unthreaded. The stud rests on the pad and is not threaded in or fastened to the pad. Self aligning feature compensates for uneven floors without sacrificing stability. Scientifically designed diamond suction cells of the neoprene insert firmly anchor the machine to the floor. Recommended for a wide range of industrial machinery and equipment where simple precise leveling is required. 25.4mm level adjustment.

Click for combined categories: All Isolation Pad Mounts


Isomounts

Hide Pictures

Go to Top  


Mounts - Isomounts

Mounts - Isomounts

Adjustable Height.

Screw and base sold separately. Order both parts for a complete unit. Designed for efficient and economic installation of a wide range of machinery. Machines can be installed rapidly and economically without bolting down. Absorb both shock and vibration within the machine and protect machines from external disturbances. Height of adjustment is through a levelling screw passing through machine foot into tapped bush in steel cover.

Mounts Base

Hide Pictures

Go to Top  


Mounts - Base - Heavy Duty

Mounts - Base - Heavy Duty

Stainless Steel Mesh. Suitable for corrosive environments. For loads of 35 to 725 kgf.

Click for combined categories: All Base Mounts


Mounts - Base - Neoprene - Style 1

Mounts - Base - Neoprene - Style 1

Threaded plate moulded into mounting. Non skid base and top surface. Type 2 has fastening slots for easy installation.

Click for combined categories: All Base Mounts


Mounts - Base - Neoprene - Style 2

Mounts - Base - Neoprene - Style 2


Click for combined categories: All Base Mounts


Mounts Bonded

Hide Pictures

Go to Top  


Mounts - Bonded

Mounts - Bonded


Click for combined categories: All Bonded Mounts


Mounts - Bonded - Two Piece

Mounts - Bonded - Two Piece

Steel insert overcoated with rubber joins the two pieces.

Click for combined categories: All Bonded Mounts


Mounts Centrebolt

Hide Pictures

Go to Top  


Mounts - Centre Bolt - Solo Unitised

Mounts - Centre Bolt - Solo Unitised

Vibration dampening

Calculate static load and select a mount of equal or greater capacity. For dynamic loads of 3 x static load select the next larger size. Lubricate mount and socket with water or rubber lubricant. Insert into socket and hand rotate with axial force. Outer Body : Natural Rubber / Spacer : Rolled Tubular Steel.

Click for combined categories: All Centrebolt Mounts


Mounts - Centre Bolt - Tandem Unitised

Mounts - Centre Bolt - Tandem Unitised

Vibration dampening

Calculate static load and select a mount of equal or greater capacity. For dynamic loads of 3 x static load select the next larger size. Lubricate mount and socket with water or rubber lubricant. Insert into socket and hand rotate with axial force. Outer Body : Natural Rubber / Spacer : Rolled Tubular Steel.

Click for combined categories: All Centrebolt Mounts


Mounts Conical

Hide Pictures

Go to Top  


Mounts - Cone - Delrin

Mounts - Cone - Delrin


Click for combined categories: All Conical Mounts


Mounts - Conical

Mounts - Conical

Vibration dampening


Click for combined categories: All Conical Mounts


Mounts Cup

Hide Pictures

Go to Top  


Mounts - Cupmounts - Industrial

Mounts - Cupmounts - Industrial

Protext against severe impact shock with efficient vibration isolation characteristics at frequencies above 40Hz.

Can be mounted in any orientation for protection of sensitive electronic, electrical and mechanical equipment from high impact shocks.

Click for combined categories: All Cup Mounts


Mounts - Vibration Isolation - Cup Style 1

Mounts - Vibration Isolation - Cup Style 1

Vibration dampening


Click for combined categories: All Cup Mounts


Mounts Cylindrical

Hide Pictures

Go to Top  


Mounts - Anti-Vibration - 303 Stainless Steel

Mounts - Anti-Vibration - 303 Stainless Steel

Corrosion resistant designed with high grade nitrile rubber and stainless steel.

Swivel movement plus or minus 7o for stable support on inclined floors. Nitrile rubber base helps ensure stability.

Mounts - Anti-Vibration - Zinc Plated Steel

Mounts - Anti-Vibration - Zinc Plated Steel

Designed with high grade nitrile rubber and zinc plated steel.

Swivel movement plus or minus 7o for stable support on inclined floors. Nitrile rubber base helps ensure stability.

Mounts - Compression

Mounts - Compression

Used for vertically applied loads to prevent the transmission of noise and vibration caused by rotation of unbalanced equipment.

Made with durable oil and ozone resistant neoprene. No special tools required for installation.

Mounts - Cylindrical - Female to Blank

Mounts - Cylindrical - Female to Blank

Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening


Click for combined categories: All Cylindrical Mounts

Related Information:
Urethane Mounts Loads and Stiffness

Rubber Mounts Forcing Frequencies


Mounts - Cylindrical - Female to Female

Mounts - Cylindrical - Female to Female

Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening


Click for combined categories: All Cylindrical Mounts

Related Information:
Urethane Mounts Loads and Stiffness

Rubber Mounts Forcing Frequencies


Mounts - Cylindrical - Male to Blank - Concave Top

Mounts - Cylindrical - Male to Blank - Concave Top

Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening


Click for combined categories: All Cylindrical Mounts

Related Information:
Urethane Mounts Loads and Stiffness

Rubber Mounts Forcing Frequencies


Mounts - Cylindrical - Male to Blank - Conical

Mounts - Cylindrical - Male to Blank - Conical

Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening


Click for combined categories: All Cylindrical Mounts


Mounts - Cylindrical - Male to Blank - Flat Top

Mounts - Cylindrical - Male to Blank - Flat Top

Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening


Click for combined categories: All Cylindrical Mounts

Related Information:
Urethane Mounts Loads and Stiffness

Rubber Mounts Forcing Frequencies


Mounts - Cylindrical - Male to Female

Mounts - Cylindrical - Male to Female

Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening


Click for combined categories: All Cylindrical Mounts

Related Information:
Urethane Mounts Loads and Stiffness

Rubber Mounts Forcing Frequencies


Mounts - Cylindrical - Male to Male

Mounts - Cylindrical - Male to Male

Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening


Click for combined categories: All Cylindrical Mounts

Related Information:
Urethane Mounts Loads and Stiffness

Rubber Mounts Forcing Frequencies


Mounts - Cylindrical - Special Purpose

Mounts - Cylindrical - Special Purpose

Vibration dampening


Click for combined categories: All Cylindrical Mounts


Mounts - Cylindrical - Square

Mounts - Cylindrical - Square

Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening

Fastener may be steel, brass or zinc plated. Natural Rubber isolator.

Click for combined categories: All Cylindrical Mounts


Mounts Finger Flex

Hide Pictures

Go to Top  


Mounts - Finger Flex Assemblies

Mounts - Finger Flex Assemblies

Cadmium Plated Steel Housing. Natural Rubber Isolators. Natural Frequency 6-30 Hz.

Mounts Leveling

Hide Pictures

Go to Top  


Mounts - Leveling - 303 Stainless - Industrial - With Acetal Pad

Mounts - Leveling - 303 Stainless - Industrial - With Acetal Pad

These industrial glides are an excellent and inexpensive solution for light duty applications such as office furniture, shelving, point of sale displays, cabinetry and small machinery.

303 Stainless Steel. Nylon pad for glide applications.

Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - 303 Stainless - Industrial - With Elastomer Pad

Mounts - Leveling - 303 Stainless - Industrial - With Elastomer Pad

These industrial mounts are an excellent and inexpensive solution for light duty applications such as office furniture, shelving, point of sale displays, cabinetry and small machinery.

303 Stainless Steel. Elastomer pad for non skid applications.

Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - Anti-Vibration - Studded Type

Mounts - Leveling - Anti-Vibration - Studded Type

Specifically designed to provide low frequency vibration isolation, leveling and shock attenuation for electronics and machinery.

15o swivel off centre to adjust to uneven surfaces. over 12mm of black neoprene permanently bonded to the base. Neoprene operating temperature -20 to 80 oC. Steel parts are zinc plated with black chromate finish.

Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - Base Type - Round

Mounts - Leveling - Base Type - Round

For loads of 45 to 5350 kg.


Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling Carry - Ball Type

Mounts - Leveling Carry - Ball Type

Vibration Dampening with retractable ball for movement.

Carry mount is a moveable mount in which the rubber mount is incorporated with a rotating ball. Allows movement of machines and provides vibration dampening. Simply turn the adjusting hole with a screwdriver to lift or lower the ball.

Click for combined categories: All Leveling Mounts

Click for combined categories: All Mounting Feet


Mounts - Leveling Carry - Castor Type

Mounts - Leveling Carry - Castor Type

Vibration Dampening with castor for movement.

Carry mount is a moveable mount in which the rubber mount is incorporated with a castor. Allows movement of machines and provides vibration dampening. Simply turn the adjusting hole with a screwdriver to lift or lower the castor.

Click for combined categories: All Leveling Mounts

Click for combined categories: All Mounting Feet


Mounts - Leveling - Elastomer Base - OSHA Yellow Steel Cover

Mounts - Leveling - Elastomer Base - OSHA Yellow Steel Cover

Protects general metalworking processes equipment including punch presses, milling machines, lathes, mixers, injection moulding machines, grinders from shock and vibration.

Simplifies installation. 63.5mm of neoprene provides controlled deflections under load. High isolation efficiency for vibration and shock forces, and reduction of transmitted sound. Adjustable up to 12.7mm above loaded height by a few turns of the leveling bolt and tightening the checknut. Corrosion resistant outer housing provides high strength. Neoprene elastomer resists oil, grease, ozone and caustics. Zinc plated hardware resists rust. Hex head bolt and locknut finished with mounts. Height dimensions indicate free height of mount under no load.

Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - Hygienic - 304 Stainless Steel

Mounts - Leveling - Hygienic - 304 Stainless Steel

ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications.


Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - Hygienic - Anchoring - Low Profile - High Swivel

Mounts - Leveling - Hygienic - Anchoring - Low Profile - High Swivel

ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications.

Operating temperature -20 to 100o C. Wrench flats in thread still allow for full use of threaded section. 12o swivel.

Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - Hygienic - Anchoring - Low Profile - Low Swivel

Mounts - Leveling - Hygienic - Anchoring - Low Profile - Low Swivel

ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications.

Operating temperature -20 to 100o C. Wrench flats in thread still allow for full use of threaded section. 1o swivel.

Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - Hygienic - Anchoring - One Hole

Mounts - Leveling - Hygienic - Anchoring - One Hole

ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications.

Operating temperature -20 to 100o C. Rubber base meets FDA 177-2600. 5o swivel for good floor contact.

Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - Hygienic - Anchoring - Two Hole

Mounts - Leveling - Hygienic - Anchoring - Two Hole

ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications.

Operating temperature -20 to 100o C. Rubber base meets FDA 177-2600. 5o swivel for good floor contact.

Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - Import High Value - Rubber Covers

Mounts - Leveling - Import High Value - Rubber Covers

For use with stud or socket type metallic leveling mounts without pads


Mounts - Leveling - Light Duty - Nylon Base

Mounts - Leveling - Light Duty - Nylon Base

Light duty perfect for furniture and small machinery leveling.

Sturdy nylon plastic base. Zinc plated steel stem.

Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - Machine - Cushioned

Mounts - Leveling - Machine - Cushioned

Reduces noise and vibration on heavy machinery, compressors and presses.

High strength aluminium alloy mounting plate is embedded in each pad with two tapped mounting holes for installation on all types of machines. The elastomer compound used in these pads is highly resistant to oil and chemicals. 1/2 UNC thread cold forged x 2.5 inch bolt supplied with each mount. Thousands of tiny suction pockets on the bottom prevent the machine from walking or slipping out of position.

Click for combined categories: All Mounting Feet


Mounts - Leveling - Nylathane - Studded Type - Single Lag Hole

Mounts - Leveling - Nylathane - Studded Type - Single Lag Hole

Max load 3200kg.


Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - Nylon - Socket Type - No Lag Holes

Mounts - Leveling - Nylon - Socket Type - No Lag Holes

Steel and stainless steel socket internal threads. Use your own custom thread length.


Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - Nylon - Studded Type - Loc-A-Lign - No Lag Holes

Mounts - Leveling - Nylon - Studded Type - Loc-A-Lign - No Lag Holes


Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - Nylon - Studded Type - Loc-A-Lign - With Lag Holes

Mounts - Leveling - Nylon - Studded Type - Loc-A-Lign - With Lag Holes


Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet



Select all items starting with...
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9



Store - Categories Pages

Go to Top





Store Pages

Go to Top





Main Pages on Small Parts and Bearings Website




Go to Top

Site Summary

Freight Rates
Terms and Conditions
Privacy Policy

Small Parts and Bearings offers 155106 products in 3673 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We ship by traceable courier only (no standard post) and we have excellent Freight Rates within Australia and worldwide.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts and Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts and Bearings 1997. All rights reserved.