Categories for: rollers
Rollers - Feed - With Aluminium Sleeve
Tolerance of Roller Outside Diameter (D) is ±0.075 mm
Urethane 60 Durometer ground outside diameter. Aluminium sleeve. Feed rollers do not have a rotating bore. They are designed to turn with the shaft.
Rollers - Idler - Neoprene With Polymer Bearing
Neoprene 60 durometer black ground outside diameter
Aluminium Alloy Sleeve. Polymer Bearing.
Rollers - Idler - Urethane Tyre - Amber Urethane
Urethane tyred bearings for escalators, elevators and more. Hardness 60 Duro.
Used in escalators, elevators, travelators, forklifts, transfer machinery, robotics and much more.
Rollers - Idler - Urethane Tyre - Black Urethane
Urethane tyred bearings for escalators, elevators and more. Hardness JIS A 95.
Used in escalators, elevators, travelators, forklifts, transfer machinery, robotics and much more. 3 designs available with or without integral spacers (extended inner rings). Low resistance to esters, ketones, aromatic solvents, trichlenes and analines. Excellent resistance to oil. Avoid prolongued exposure to sunlight, moisture or high temperature.
Rollers - Idler - Urethane With Polymer Bearing
Urethane 60 durometer ground outside diameter
Aluminium Alloy Sleeve. Polymer Bearing.
Rollers - Idler - With Flanged Sintered Bearing
60 Durometer Urethane Roller Surface. With flanged self lubricating sintered bronze bearings pressed into an aluminium sleeve.
No chamfer on the rollers.
Rollers - Nylon Tyre - Angled - Threaded Bore
Nylon tyred rollers for cabinet doors, gym equipment etc
Rollers - Nylon Tyre - Convex - Threaded Bore
Nylon tyred rollers for cabinet doors, gym equipment etc
Rollers - Nylon Tyre - Convex - Through Bore
Nylon tyred rollers for cabinet doors, gym equipment etc
Rollers - Urethane Feed - With Hub
Urethane coated aluminium alloy feed rollers with hub.
Roller - Urethane 60 Durometer, Ground Outside Diameter. Sleeve - Aluminium.
Low cost alternative for making your own wheels, castors, rollers, sheaves etc.
Blue outer tyre 90A Durometer bonded to a hard brown 75D Durometer inner sleeve. This results in a hard anti friction bearing surface inside with a soft tyre outside. The roller can be cut and machined to suit your purposes. Testing for your application is recommended.
Urethane tyred cam yoke rollers for noise reduction, reduced wear and non marking
Polycoated shore 80A cast urethane cover.
Bearings - Pressure Roller - With Urethane OD
Bearings with Urethane Tyre on OD for applications requiring frictional movement.
For applications including paper and card dispensing and rolling (eg ATM Machines).
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
For precise linear motion.
Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100°C ( Constant), +140°C (Maximum). For temperatures over 100°C we can supply special high temperature grease (200°C - supplied in syringe) CG2-SY.
Chain - Roller - Metal - Miniature - Hobby 1/12 Scale Bike
This 1/12 scale metal bike chain comes as a kit. Plastic sprockets are included.
The chain needs to be assembles one link at a time.
Chain - Roller - Plastic - Simplex
Includes acetal, polyproylene and nylon. Miniature size from 3.1mm up to 12.7mm
Snap together construction - no joining links required.
Slides - Linear - Cross Roller Rail
Compact, precision bearings that can support and guide high loads with high accuracy and repeatability, low friction, and low starting force.
Each consists of a pair of hardened steel ways containing 90 deg V grooves and a row of alternately crossed cylindrical rollers. Installed faced to face on smooth flat and accurately parallel, coplanar or perpendicular surfaces. Lubrication required, light grease for low speeds to continuous oil bath/mist for high speeds.
Polyacetal catch and strike with polyethylene rollers. Ideal in corrosive environments.
Complete with Needle Roller or Ball Bearings. 3.75mm to 25.4mm pitch.
Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.
Cam Followers - Roller Type - Easy Mounting
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
Cam Followers - Roller Type - Eccentric Stud
Carbon steel roller type cam followers with eccentric stud.
Carbon Steel - Synthetic rubber seals assembled in the outer ring. Screwdriver slot for mounting. Stud designed to fit H7 housing.
Cam Followers - Roller Type - Miniature - Standard
Small carbon steel roller type cam followers.
Carbon Steel - Nitrile Rubber seals assembled in the outer ring. Screwdriver slot for mounting. Stud designed to fit H7 housing.
Cam Followers - Roller Type - Miniature - Thrust Disc
Small carbon steel thrust disc roller type cam followers.
CFS. W: High Carbon Steel (all parts). CFS. FW: Stainless Steel - hard, similar to 440C (all parts). Stud designed to fit H7 housing.
Cam Followers - Roller Type - Stainless Steel
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
Cam Followers - Roller Type - Standard
Carbon steel roller type cam followers.
Load 1 applies when outer race is mounted into a housing with standard bearing fit. Load 2 applies when used as a track roller. Stud designed to fit H7 housing.
Cam Followers - Roller Type - Thrust Disc
Carbon steel thrust disc roller type cam followers.
CF.WBR, CF.WBUUR: High Carbon Steel. CF.FWBR, CF.FWBUUR: Stainless Steel. Seals: Synthetic Rubber. Stud designed to fit H7 housing.
Cam Followers - Roller Type - Urethane Covered
Urethane tyred cam followers for noise reduction, reduced wear and non marking
Housings - Bearing - Pillow Block - Needle Roller Bearing
Aluminium with 5 percent self aligning drawn cup needle roller bearing.
Bearing: Drawn cup needle roller. / Housing: Sintered Aluminium / Corrosion Resistant. Mating shaft recommendation: Min. hardening 58 HRC (Rockwell C). Max surface finish 16 RMS. Recommended shaft clearance is 0.013 - 0.038mm, using lower limit of bore tolerance.
Roller Clutch Bearings rotate in one direction only.
Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.
Bearings - Press-Fit - Needle Roller - SDP - Non Aligning - Self Clinching
Knurled edge clinches into softer materials.
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
Bearings - Press-Fit - Needle Roller - SDP - Self Aligning - Self Clinching
Self aligning to 5 Degrees. Knurled edge clinches into softer materials.
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Self aligning +/- 5 Degress. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
Bearings - SDP - Needle Roller - Flange Mounted - Non Aligning
Bearings - SDP - Needle Roller - Flange Mounted - Self Aligning
Rod Ends - Steel - Heavy Duty - Roller
With integral self aligning roller bearing.
With grease nipple. Housing: Tempered forged steel. Bearing Race: Case hardened. Thread: Rolled - Surface galvanised. Inner Ring: Ball bearing steel. Hardened, ground. Lubrication: Calcium Complex Soap Grease temperature range -20ºC to +120ºC.
Ball Slides and Crossed Roller Positioning Stages
Used for Gauging and Positioning Light to Medium Loads.
Spring loaded micrometer drives allow precise repeatable adjustments with low friction and zero backlash. Positioning Slides can be stacked for Multi axis applications. Preloaded positioning slides fully assemebled. Black Anodized Finish.
Universal Joints - Hex Bore Quick Release Needle Roller
DIN808-W Low Backlash with Sealed Bearings
Forged centre cross with hard ground ends for sealed needle bearings. 4000 RPM Max. Round bore one side. Hex bore on the quick release.
Universal Joints - Quick Release Needle Roller - Integral Shaft
DIN808-W Low Backlash with Sealed Bearings
Forged centre cross with hard ground ends for sealed needle bearings. 4000 RPM Max. Round bore both sides.
Universal Joints - Quick Release Needle Roller - Integral Shaft - Hex Bore
DIN808-W Low Backlash with Sealed Bearings
Forged centre cross with hard ground ends for sealed needle bearings. 4000 RPM Max. Integral shaft one side. Hex bore on the quick release.
Universal Joints - Quick Release Needle Roller - Round Bore
DIN808-W Low Backlash with Sealed Bearings
Forged centre cross with hard ground ends for sealed needle bearings. 4000 RPM Max. Round bore both sides.
Universal Joints - Telescoping - Spline Type - Needle Roller
Max Speed 4000 RPM.
Steel 9SMn Pb36K DIN808-W. Max. Working Angle - 60 Deg. Max. Speed 4000 RPM.
Bearings with a spherical outside diameter.
Combined listing of spherical OD track rollers and bearings for Linear Guide systems.
Vee grooved track roller bushings.
Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned.
Vee grooved track roller guide wheels with Abec 5 precision bearings.
Match with correct Track Size.
Dual Vee - Guide Wheels - Studded
Vee grooved track roller guide wheels.
Match with correct Track Size. Note! OD is reference only. Allow up to 1.2 mm larger than listed.
Dual Vee - Tracks with Mounting Holes
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
Dual Vee - Tracks without Mounting Holes
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
Bearings - Spyraflo - Flanged Housing - Self Aligning
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information. +/- 5% Static Alignment. Sintered aluminium housing. Corrosion Resistant. Light weight.
Bearings - Spyraflo - Flange Mount - Non Aligning
Low profile flange mounted needle roller and bronze bearings
See links at bottom of web page for more information.Too many choices?
You have selected to see ALL categories including any of the following words: rollers
Click here to see ONLY THE MOST POPULAR categories including any of the following words: rollers
|
| |||||||||||||||||||||||||
| Select all items starting with... | |||||||||||||||||||||||||
| A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | Or use the category search | ||||||||||||||||
|
| |||||||||||||||||||||||||
