Right Angle Gearboxes - Small Parts And Bearings Categories

FOUND IN PART NUMBERS:- The item was found in our part numbers database. The results of this search are shown below. If you would prefer to run the search again without checking the part numbers database please Click Here

Possible part number matches for
Matching Part

JBS-M05.0Rx28.50-CS found in Joints - Ball and Socket - Right Angle - Light Duty
Thread: M5x0.8 (5mm Standard) Right Hand. Length (L): 28.50. Material: Carbon Steel (Low Carbon).

Stock: 10


Matching Part

JBS-M05.0Rx28.50-SS found in Joints - Ball and Socket - Right Angle - Light Duty
Thread: M5x0.8 (5mm Standard) Right Hand. Length (L): 28.50. Material: Stainless.

Stock: 1


Matching Part

JBS-M06.0Rx32.50-CS found in Joints - Ball and Socket - Right Angle - Light Duty
Thread: M6x1.00 Right Hand. Length (L): 32.50. Material: Carbon Steel (Low Carbon).

Stock: 8


Matching Part

JBS-M08.0Rx39.50-CS found in Joints - Ball and Socket - Right Angle - Light Duty
Thread: M8x1.25 Right Hand. Length (L): 39.50. Material: Carbon Steel (Low Carbon).

Stock: 13


Matching Part

JBS-M10.0Rx47.00-CS found in Joints - Ball and Socket - Right Angle - Light Duty
Thread: M10x1.50 Right Hand. Length (L): 47.00. Material: Carbon Steel (Low Carbon).

Stock: 1


Matching Part

JBS-M10.0Rx47.00-SS found in Joints - Ball and Socket - Right Angle - Light Duty
Thread: M10x1.50 Right Hand. Length (L): 47.00. Material: Stainless.

Stock: 4


Matching Part

JBS-M12.0Rx47.00-CS found in Joints - Ball and Socket - Right Angle - Light Duty
Thread: M12x1.75 Right Hand. Length (L): 47.00. Material: Carbon Steel (Low Carbon).

Stock: 1


Matching Part

GDLBP-1-4.8R-0.11 found in Gearboxes - Right Angle - Model RA 0625-0508-0300 - 62.5 x 50.8 x 30.0mm
Ratio: 1 to 1. Shafts Diameter (d): 4.76. Shaft Positions: Top / Right.

Backorder


Matching Part

GDLBP-1-4.8R-0.34 found in Gearboxes - Right Angle - Model RA 0625-0508-0300 - 62.5 x 50.8 x 30.0mm
Ratio: 1 to 1. Shafts Diameter (d): 4.76. Shaft Positions: Top / Right.

Backorder


Matching Part

GDLBP-1-4R-0.12 found in Gearboxes - Right Angle - Model RA 0625-0508-0300 - 62.5 x 50.8 x 30.0mm
Ratio: 1 to 1. Shafts Diameter (d): 4.00. Shaft Positions: Top / Right.

Backorder



Gearboxes Right Angle

Hide Pictures

Go to Top  


Gearboxes - Right Angle - Model RA 0365-0365-0294 - 36.5 x  36.5 x 29.4mm

Gearboxes - Right Angle - Model RA 0365-0365-0294 - 36.5 x 36.5 x 29.4mm

1:1 ratio. GDRA Series. Miniature gearbox.


Click for combined categories: All Right Angle Gearboxes


Gearboxes - Right Angle - Model RA 0400-0400-0250 - 40.0 x  40.0 x 25.0mm

Gearboxes - Right Angle - Model RA 0400-0400-0250 - 40.0 x 40.0 x 25.0mm

BLH20 Series. Miniature gearbox.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.

Click for combined categories: All Right Angle Gearboxes


Gearboxes - Right Angle - Model RA 0300-0300-0180 - 30.0 x  30.0 x 18.0mm

Gearboxes - Right Angle - Model RA 0300-0300-0180 - 30.0 x 30.0 x 18.0mm

Economy Bevel Gear Type. Miniature gearbox.

Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.

Click for combined categories: All Right Angle Gearboxes


Gearboxes - Right Angle - Model RA 0400-0400-0200 - 40.0 x  40.0 x 20.0mm

Gearboxes - Right Angle - Model RA 0400-0400-0200 - 40.0 x 40.0 x 20.0mm

Mitre Gears 1:1 ratio. GDRA Series. Miniature gearbox.

Max Speed 3000 RPM. Max Backlash 1o. Ball bearings both ends. Base mounting both sides.

Click for combined categories: All Right Angle Gearboxes


Gearboxes - Right Angle - Model RA 0500-0500-0300 - 50.0 x  50.0 x 30.0mm

Gearboxes - Right Angle - Model RA 0500-0500-0300 - 50.0 x 50.0 x 30.0mm

Economy Bevel Gear Type. GDRA Series.

Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.

Click for combined categories: All Right Angle Gearboxes


Gearboxes - Right Angle - Model RA 0625-0508-0300 - 62.5 x  50.8 x 30.0mm

Gearboxes - Right Angle - Model RA 0625-0508-0300 - 62.5 x 50.8 x 30.0mm

Bevel Gears - Plastic Housing. GDLBP Series.

Max Backlash 5o.

Click for combined categories: All Right Angle Gearboxes


Gearboxes - Right Angle - Model RA 0665-0508-0508 - 66.55 x 50.8 x 50.8mm

Gearboxes - Right Angle - Model RA 0665-0508-0508 - 66.55 x 50.8 x 50.8mm

1 to 1 ratio with rated speeds up to 1800rpm. Sealed gearcase. Key drive shafts. Keys included.

4140 Heat Treated steel gears and shafts. Aluminium alloy hard anodised case. Maximum operating temperature 90 Deg C (200 Deg F). Optional foot mount plates available - also listed in this category.

Click for combined categories: All Right Angle Gearboxes


Gearboxes - Right Angle - Model RA 0800-0800-0400 - 80.0 x  80.0 x 40.0mm

Gearboxes - Right Angle - Model RA 0800-0800-0400 - 80.0 x 80.0 x 40.0mm

Mitre Gears 1:1 ratio. GDRA Series.

Max Speed 3000 RPM. Max Backlash 1o. Ball bearings both ends. Base mounting both sides.

Click for combined categories: All Right Angle Gearboxes


Gearboxes - Right Angle Model RA 0400-0400-0250(B) - 40.0 x  40.0 x 25.0mm (B)

Gearboxes - Right Angle Model RA 0400-0400-0250(B) - 40.0 x 40.0 x 25.0mm (B)

Economy Bevel Gear Type. GDRA Series. Miniature gearbox.

Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.

Click for combined categories: All Right Angle Gearboxes


Gearboxes - Right Angle - Model RA 0750-0440-0440 - 75.0 x  44.0 x  44.0mm

Gearboxes - Right Angle - Model RA 0750-0440-0440 - 75.0 x 44.0 x 44.0mm

Bevel Gears - 1.6 Nm-5.0 Nm ratios 6:1 to 24:1. BLN20 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Gear: Steel 655M13 (EN36) Hardened. Backlash: Depends on ratio. Max. Input Speed: 4000 Rpm. Lubrication: Greased for life - Shell Alvania Grease HDX2.

Click for combined categories: All Right Angle Gearboxes


Gearboxes - Right Angle - Model RA 0855-0778-0318 - 85.5 x  77.8 x  31.8mm

Gearboxes - Right Angle - Model RA 0855-0778-0318 - 85.5 x 77.8 x 31.8mm

Bevel Gears - Plastic Housing. GDLBP Series.

Max Backlash 5o.

Click for combined categories: All Right Angle Gearboxes


Gearboxes - Right Angle - Model RA 0550-0550-0340 - 55.0 x  55.0 x 34.0mm

Gearboxes - Right Angle - Model RA 0550-0550-0340 - 55.0 x 55.0 x 34.0mm

BLH30 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.

Click for combined categories: All Right Angle Gearboxes


Gearboxes - Right Angle - Model RA 0750-0750-0440 - 75.0 x  75.0 x 44.0mm

Gearboxes - Right Angle - Model RA 0750-0750-0440 - 75.0 x 75.0 x 44.0mm

BLH40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.

Click for combined categories: All Right Angle Gearboxes


Gearboxes - Right Angle - Model RA 1000-1000-0600 -100.0 x 100.0 x 60.0mm

Gearboxes - Right Angle - Model RA 1000-1000-0600 -100.0 x 100.0 x 60.0mm

BLH50 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.

Click for combined categories: All Right Angle Gearboxes


Gearboxes - Right Angle - Model RA 1400-1400-0980 -140.0 x 140.0 x 98.0mm

Gearboxes - Right Angle - Model RA 1400-1400-0980 -140.0 x 140.0 x 98.0mm

BLH70 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.

Click for combined categories: All Right Angle Gearboxes


Gearbox Output Shafts

Hide Pictures

Go to Top  


Gearboxes - Output Shafts - For E Type Helical Reducers

Gearboxes - Output Shafts - For E Type Helical Reducers

For use in Right Angle gearboxes with bores. E Series.

Stainless 303 shaft. Steel keys and circlips. E-X and E-DX types suitable for E type gearboxes (right angle types).

Click for combined categories: All Shafts


Gearboxes Tee

Hide Pictures

Go to Top  


Gearboxes - Tee -  38.9 x  38.1 x 27.0mm A

Gearboxes - Tee - 38.9 x 38.1 x 27.0mm A

Worm Gear. WG11 Series. Miniature gearbox.

Maximum input speed 2000 RPM. Maximum Backlash 5o. Worm Gears.

Click for combined categories: All Tee Gearboxes


Gearboxes Inline

Hide Pictures

Go to Top  


Gearboxes - Inline -  27 x  45mm

Gearboxes - Inline - 27 x 45mm

J27 Series. Miniature gearbox.

Case: Aluminium. Gear: Stainless Steel 303S21/31. Bearing: 440C. Weight: 60g. Backlash: Depends on ratio. Hours Life: 12000 hr. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.

Click for combined categories: All Inline Gearboxes

Related Information:
Inexpensive Gearmotor Kits


Gearboxes Tee

Hide Pictures

Go to Top  


Gearboxes - Tee -  38.9 x  38.1 x 27.0mm B

Gearboxes - Tee - 38.9 x 38.1 x 27.0mm B

1:1, 2:1 and 3:1 ratios. GDRA Series. Miniature gearbox.

Max Speed 2000 RPM. Max Backlash 5o. Bevel Gears.

Click for combined categories: All Tee Gearboxes


Gearboxes Cross Axis

Hide Pictures

Go to Top  


Gearboxes - Cross Axis - 104 x  63 x  63

Gearboxes - Cross Axis - 104 x 63 x 63

Helical or Wormwheel Gears. 15mm Bores. E40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Helical Gears and Worms : Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Worm Wheel : Aluminium Bronze (CA104 / AB2). Circlips : Steel (not plated). Bearing : Steel 2RS (Rubber seals fitted).

Click for combined categories: All Cross Axis Gearboxes


Gearboxes - Cross Axis -  52 x  34 x  34

Gearboxes - Cross Axis - 52 x 34 x 34

Helical or Wormwheel Gears. 6mm Bores. E20 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Helical Gears and Worms: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Worm Wheel: Aluminium Bronze (CA104 / AB2). Circlips: Steel (not plated). Bearing: Steel 2RS (Rubber seals fitted).

Click for combined categories: All Cross Axis Gearboxes

Related Information:
Output Shafts


Gearboxes - Cross Axis -  78 x  48 x  48

Gearboxes - Cross Axis - 78 x 48 x 48

Helical or Wormwheel Gears. 10mm Bores. E30 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Helical Gears and Worms : Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Worm Wheel : Aluminium Bronze (CA104 / AB2). Circlips : Steel (not plated). Bearing : Steel 2RS (Rubber seals fitted).

Click for combined categories: All Cross Axis Gearboxes

Related Information:
Output Shafts


Gearboxes - Cross Axis - 150 x  96 x  96 A

Gearboxes - Cross Axis - 150 x 96 x 96 A

Helical or Wormwheel Gears. 25mm Bores. E60 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Helical Gears and Worms : Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Worm Wheel : Aluminium Bronze (CA104 / AB2). Circlips : Steel (not plated). Bearing : Steel 2RS (Rubber seals fitted).

Click for combined categories: All Cross Axis Gearboxes

Related Information:
Output Shafts


Gearboxes Tee

Hide Pictures

Go to Top  


Gearboxes - Tee - 100.0 x  75.0 x  44.0mm

Gearboxes - Tee - 100.0 x 75.0 x 44.0mm

Bevel Gears - 3.0 to 10.3 Nm. BLHM40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.

Click for combined categories: All Tee Gearboxes


Gearboxes - Tee -  55.0 x  40.0 x  25.0mm

Gearboxes - Tee - 55.0 x 40.0 x 25.0mm

Bevel Gears - 0.53 to 1.77 Nm. BLHM20 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.

Click for combined categories: All Tee Gearboxes


Gearboxes - Tee -  62.5 x  50.8 x  30.0mm

Gearboxes - Tee - 62.5 x 50.8 x 30.0mm

Bevel Gears - Plastic Housing. GDLBP Series.

Max Backlash 5o.

Click for combined categories: All Tee Gearboxes


Gearboxes - Tee -  85.5 x  77.8 x  31.8mm

Gearboxes - Tee - 85.5 x 77.8 x 31.8mm

Bevel Gears - Plastic Housing. GDLBP Series.

Max Backlash 5o.

Click for combined categories: All Tee Gearboxes


Gearboxes Cross Axis

Hide Pictures

Go to Top  


Gearboxes - Cross Axis - 136.5 x 111.1 x  63.5

Gearboxes - Cross Axis - 136.5 x 111.1 x 63.5

Worm gears.

Maximum input speed 1800 RPM. Approx weight 2.7 KG (6 lb).

Click for combined categories: All Cross Axis Gearboxes


Gearboxes - Cross Axis -  52.4 x  44.5 x  25.4

Gearboxes - Cross Axis - 52.4 x 44.5 x 25.4

Worm Gears. Precision Quality - Input Speeds up to 6000 RPM.

Max Input : 6000 RPM. Backlash at Output : 0 Deg 30 Min. Packed with grease at assembly - temp range -32 Deg C to +146 Deg C (-25 F to 295 F).

Click for combined categories: All Cross Axis Gearboxes


Gearboxes - Cross Axis -  77.8 x  63.5 x  34.9

Gearboxes - Cross Axis - 77.8 x 63.5 x 34.9

Worm Gears. Precision Quality - Input Speeds up to 6000 RPM.

Max Input : 6000 RPM. Backlash at Output : 0 Deg 30 Min. Packed with grease at assembly - temp range -32 Deg C to +146 Deg C (-25 F to 295 F).

Click for combined categories: All Cross Axis Gearboxes


Gearboxes - Cross Axis -  85.6 x  66.7 x  34.9

Gearboxes - Cross Axis - 85.6 x 66.7 x 34.9

Worm Gears - Commercial size 26.

Maximum input speed 1800 RPM. Approx weight 0.6 KG (20 oz).

Click for combined categories: All Cross Axis Gearboxes


Gearboxes Inline

Hide Pictures

Go to Top  


Gearboxes - Inline - 112.0 x  52.0 Low Backlash

Gearboxes - Inline - 112.0 x 52.0 Low Backlash

Taper Gears - Weight: 1.50kg. TG112 Series.

Case: Anodised Aluminum 6082. Taper Gears: 817M40T High Carbon Steel. Weight: 1.50kg. Output Backlash: Less than 8.1 arc/min at output. Max Input Speed: 3000 Rpm.

Click for combined categories: All Inline Gearboxes

Related Information:
Inexpensive Gearmotor Kits


Gearboxes Cross Axis

Hide Pictures

Go to Top  


Gearboxes - Cross Axis -  38.9 x  31.8 x  19.1mm

Gearboxes - Cross Axis - 38.9 x 31.8 x 19.1mm

Worm Gears - Precision.

Max Input : 6000 RPM. Backlash at Output : 0 Deg 30 Min. Packed with grease at assembly - temp range -32 Deg C to +146 Deg C (-25 F to 295 F).

Click for combined categories: All Cross Axis Gearboxes


Gearboxes Tee

Hide Pictures

Go to Top  


Gearboxes - Tee -  36.5 x  36.5 x 29.4mm

Gearboxes - Tee - 36.5 x 36.5 x 29.4mm

GDRAB Series. Miniature gearbox.


Click for combined categories: All Tee Gearboxes


Gearboxes Cross Axis

Hide Pictures

Go to Top  


Gearboxes - Cross Axis - 110 x  95 x  38mm

Gearboxes - Cross Axis - 110 x 95 x 38mm

Worm and Wormwheel box. 10.3 to 40.0Nm. 5:1 to 120:1 ratios. P45 and PF45 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Click for combined categories: All Cross Axis Gearboxes

Related Information:
Output Shafts


Gearboxes - Cross Axis - 130 x 110 x  46mm

Gearboxes - Cross Axis - 130 x 110 x 46mm

Worm and Wormwheel box. 13.4 to 57.0Nm. 5:1 to 120:1 ratios. P55 and PF55 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Click for combined categories: All Cross Axis Gearboxes

Related Information:
Output Shafts


Gearboxes - Cross Axis - 150 x 125 x  54mm

Gearboxes - Cross Axis - 150 x 125 x 54mm

Worm and Wormwheel box. 30.0 to 118.0Nm. 5:1 to 120:1 ratios. P60 and PF60 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Click for combined categories: All Cross Axis Gearboxes


Gearboxes - Cross Axis - 170 x 145 x  60mm

Gearboxes - Cross Axis - 170 x 145 x 60mm

Worm and Wormwheel box. 38.0 to 164.0Nm. 5:1 to 120:1 ratios. P70 and PF70 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Click for combined categories: All Cross Axis Gearboxes

Related Information:
Output Shafts


Gearboxes - Cross Axis -  47 x  40 x  22mm

Gearboxes - Cross Axis - 47 x 40 x 22mm

Worm and Wormwheel box. 1.4 to 2.5Nm. 5:1 to 120:1 ratios. P20 and PF20.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Click for combined categories: All Cross Axis Gearboxes

Related Information:
Output Shafts


Gearboxes - Cross Axis -  70 x  60 x  28mm

Gearboxes - Cross Axis - 70 x 60 x 28mm

Worm and Wormwheel box. 2.5 to 8.8Nm. 5:1 to 120:1 ratios. P30 and PF30 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Click for combined categories: All Cross Axis Gearboxes

Related Information:
Output Shafts


Gearboxes - Cross Axis -  90 x  75 x  32mm

Gearboxes - Cross Axis - 90 x 75 x 32mm

Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Click for combined categories: All Cross Axis Gearboxes

Related Information:
Output Shafts


Gearboxes Offset

Hide Pictures

Go to Top  


Gearboxes - Offset - 175 x 150 x  60

Gearboxes - Offset - 175 x 150 x 60

FF30 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Gear: High Carbon Steel 817M40(EN24). Weight 5.5kg. Backlash: 1o. Hours Life: 12000 hr. Max Input Speed: 1500 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. You will need to assess duty, cycles and confirm gearbox suitability with your own calculations. Torque figures are to be used for guidance only.

Click for combined categories: All Offset Gearboxes

Related Information:
Output Shafts


Gearboxes - Offset -  60 x  60

Gearboxes - Offset - 60 x 60

Base mounted. SRBM60 Series.

Die cast aluminium Housing. Steel Shafts. Bearings Input / Output : Ball / Sintered Bronze. Steel and Phenolic Gears. Shaft Play Radial / Thrust : Less than 0.11mm / Less than 0.31mm. Operating Temp : -10 to 60 Deg C | Approx weight : 26 grams.

Click for combined categories: All Offset Gearboxes


Gearboxes Inline

Hide Pictures

Go to Top  


Gearboxes - Inline - 114 x  90mm

Gearboxes - Inline - 114 x 90mm

NT121 Series.

Case: Aluminium, Gear: 655M13 Hardened. Weight: 2.6/4.0kg, Backlash: Depends on ratio. Max Input Speed: 3000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.

Click for combined categories: All Inline Gearboxes

Related Information:
Inexpensive Gearmotor Kits


Gearboxes - Inline -  63 x  50mm

Gearboxes - Inline - 63 x 50mm

J65 Series.

End Caps: AA15 Red Anodised Aluminum (6082-T6). Centre Body: Black Delrin. Gears: High Carbon Steel 817M40(EN24). Weight: 0.3kg. Backlash: Depends on ratio. Max Input Speed: 4000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.

Click for combined categories: All Inline Gearboxes

Related Information:
Inexpensive Gearmotor Kits


Gearboxes Bu-Ord

Hide Pictures

Go to Top  


Gearboxes - Bu-Ord - Size 11 - Double End

Gearboxes - Bu-Ord - Size 11 - Double End

SRBO11 Series.

Items listed as Zero Backlash are for loads less than the ZB Torque Limit shown. Not recommended to be used as speed increasers - speed reducers only.

Click for combined categories: All Bu-Ord Gearboxes


Gearboxes - Bu-Ord - Size 15 - Double End

Gearboxes - Bu-Ord - Size 15 - Double End

SRBO15 Series.

Not recommended to be used as speed increasers - speed reducers only.

Click for combined categories: All Bu-Ord Gearboxes


Gearboxes - Bu-Ord - Size 15 - Single End

Gearboxes - Bu-Ord - Size 15 - Single End

SRBO15 Series.

Not recommended to be used as speed increasers - speed reducers only.

Click for combined categories: All Bu-Ord Gearboxes


Gearboxes - Bu-Ord - Size 18 - Double End

Gearboxes - Bu-Ord - Size 18 - Double End

SRBO18 Series.

Not recommended to be used as speed increasers - speed reducers only.

Click for combined categories: All Bu-Ord Gearboxes


Gearboxes Tee

Hide Pictures

Go to Top  


Gearboxes - Tee - 100.0 x 100.0 x 60.0mm

Gearboxes - Tee - 100.0 x 100.0 x 60.0mm

BLHT50 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.

Click for combined categories: All Tee Gearboxes


Gearboxes - Tee -  55.0 x  55.0 x 34.0mm

Gearboxes - Tee - 55.0 x 55.0 x 34.0mm

BLHT30 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.

Click for combined categories: All Tee Gearboxes


Gearboxes - Tee -  65.0 x  50.0 x 50.0mm

Gearboxes - Tee - 65.0 x 50.0 x 50.0mm

BL8 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Bevel: Medium Carbon Steel 080M40(EN8). Backlash: 1o. Lubrication: Greased for life - Shell Nerita Grease HV.

Click for combined categories: All Tee Gearboxes


Gearboxes - Tee -  75.0 x  75.0 x 44.0mm

Gearboxes - Tee - 75.0 x 75.0 x 44.0mm

BLHT40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.

Click for combined categories: All Tee Gearboxes


Gearboxes - Tee -  80.0 x  60.0 x 50.0mm

Gearboxes - Tee - 80.0 x 60.0 x 50.0mm

BL8 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Bevel: Medium Carbon Steel 080M40(EN8). Backlash: 1o. Lubrication: Greased for life - Shell Nerita Grease HV.

Click for combined categories: All Tee Gearboxes


Gearbox Output Shafts

Hide Pictures

Go to Top  


Gearboxes - Output Shafts - For P Type Worm Reducers

Gearboxes - Output Shafts - For P Type Worm Reducers

For use in Cross Axis gearboxes with bores. P and PF Series.

Stainless 303 shaft. Steel keys and circlips. P-X and P-DX types suitable for P and PF type gearboxes (cross axis types).

Click for combined categories: All Shafts


Angle

Hide Pictures

Go to Top  


Angle - Brass

Angle - Brass


Gearboxes Educational Kits

Hide Pictures

Go to Top  


Educational Gearbox Kits

Educational Gearbox Kits

Basic gearbox kits for prototyping, testing and learning


Tensioners

Hide Pictures

Go to Top  


Tensioner - Fixed Angle

Tensioner - Fixed Angle

Use with idler shafts and idler pulleys. Can be mounted on top of any flat surface to provide horizontal tenaioning.

Idler shaft and pulleys not included with tensioner.

Click for combined categories: All Tensioner Arms


Ball Joints

Hide Pictures

Go to Top  


Joints - Ball and Socket - Right Angle - Light Duty

Joints - Ball and Socket - Right Angle - Light Duty

Light duty ball joints provide a pivot point. They are unhardened and should not be used for high load or high repetition applications. Clearance is not specified, so actual joints may range from very loose to reasonably tight.

Steel Type: Zinc Passivated Induction Hardened. Stainless Steel Type: 303 Grade unhardened. Max. Static push/pull loads are valid for both radial and axial loads. Standard Steel type Ball Stud Tensile strength: Rm = 600 N/mm sq (Not applicable to stainless type). Standard Steel type Housing Tensile strength: Rm = 500 N/mm sq (Not applicable to stainless type).

Click for combined categories: All Ball Joints


Gears Metric Bevel

Hide Pictures

Go to Top  


Gears - Bevel - Module 1

Gears - Bevel - Module 1

For 90o angle power transfer.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Bevel Gears

Related Information:
Module 1 Mitre Gears


Gears - Bevel - Module 2

Gears - Bevel - Module 2

For 90o angle power transfer.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Bevel Gears

Related Information:
Module 2 Mitre Gears


Gears - Bevel - Module 3

Gears - Bevel - Module 3

For 90o angle power transfer.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Bevel Gears

Related Information:
Module 3 Mitre Gears


Gears Metric Mitre

Hide Pictures

Go to Top  


Gears - Mitre - Module 1

Gears - Mitre - Module 1

1:1 Ratio. 20o Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Mitre Gears

Related Information:
Module 1 Bevel Gears

Module 1 Spiral Mitre Gears


Gears - Mitre - Module 2

Gears - Mitre - Module 2

1:1 Ratio. 20o Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Mitre Gears

Related Information:
Module 2 Bevel Gears

Module 2 Spiral Mitre Gears


Gears - Mitre - Module 3

Gears - Mitre - Module 3

1:1 Ratio. 20o Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Mitre Gears

Related Information:
Module 3 Bevel Gears

Module 3 Spiral Mitre Gears


Gears Metric Racks

Hide Pictures

Go to Top  


Gears - Racks - Module 1

Gears - Racks - Module 1

20o Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.

Plastic and metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Gear Racks


Gears - Racks - Module 2

Gears - Racks - Module 2

20o Pressure Angle. Carbon steel, acetal and nylon.

Plastic and metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Gear Racks


Gears - Racks - Module 3

Gears - Racks - Module 3

20o Pressure Angle. Carbon steel, acetal and nylon.

Plastic and metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Gear Racks


Gears Metric Spur

Hide Pictures

Go to Top  


Gears - Spur - Module 1

Gears - Spur - Module 1

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears - Spur - Module 2

Gears - Spur - Module 2

PCD = No. of Teeth x 2.000mm. 20o Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears - Spur - Module 3

Gears - Spur - Module 3

PCD = No. of Teeth x 3.000mm. 20o Pressure Angle. 303 stainless steel, carbon steel and nylon.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears - Spur - Module 0.3

Gears - Spur - Module 0.3

PCD = No. of Teeth x 0.300mm. 20o Pressure Angle. Brass.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears - Spur - Module 0.4

Gears - Spur - Module 0.4

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. 416 stainless steel, acetal, brass and carbon steel.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears - Spur - Module 0.5

Gears - Spur - Module 0.5

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears - Spur - Module 0.7

Gears - Spur - Module 0.7

PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears - Spur - Module 0.8

Gears - Spur - Module 0.8

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears - Spur - Module 1.5

Gears - Spur - Module 1.5

PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears - Spur - Module 2.5

Gears - Spur - Module 2.5

PCD = No. of Teeth x 2.500mm. 20o Pressure Angle. 303 stainless steel, carbon steel and nylon.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears Metric Bevel

Hide Pictures

Go to Top  


Gears - Bevel - Module 0.5

Gears - Bevel - Module 0.5

For 90o angle power transfer.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Bevel Gears

Related Information:
Module 0.5 Mitre Gears


Gears - Bevel - Module 0.8

Gears - Bevel - Module 0.8

For 90o angle power transfer.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Bevel Gears

Related Information:
Module 0.8 Mitre Gears


Gears - Bevel - Module 1.5

Gears - Bevel - Module 1.5

For 90o angle power transfer.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Bevel Gears

Related Information:
Module 1.5 Mitre Gears


Gears - Bevel - Module 2.5

Gears - Bevel - Module 2.5

For 90o angle power transfer.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Bevel Gears

Related Information:
Module 2.5 Mitre Gears


Gears Metric Mitre

Hide Pictures

Go to Top  


Gears - Mitre - Module 0.5

Gears - Mitre - Module 0.5

1:1 Ratio. 20o Pressure Angle - Brass and acetal.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Mitre Gears

Related Information:


Gears - Mitre - Module 0.6

Gears - Mitre - Module 0.6

1:1 Ratio. 20o Pressure Angle - Stainless steel, brass, aluminium and acetal.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Mitre Gears


Gears - Mitre - Module 0.8

Gears - Mitre - Module 0.8

1:1 Ratio. 20o Pressure Angle - Acetal and brass.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Mitre Gears

Related Information:
Module 0.8 Bevel Gears


Gears - Mitre - Module 1.5

Gears - Mitre - Module 1.5

1:1 Ratio. 20o Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Mitre Gears

Related Information:
Module 1.5 Bevel Gears

Module 1.5 Spiral Mitre Gears


Gears - Mitre - Module 2.5

Gears - Mitre - Module 2.5

1:1 Ratio. 20o Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Mitre Gears

Related Information:
Module 2.5 Bevel Gears

Module 2.5 Spiral Mitre Gears


Gears - Mitre - Module 3.5

Gears - Mitre - Module 3.5

1:1 Ratio. 20o Pressure Angle - Zinc die cast and steel.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Click for combined categories: All Metric Mitre Gears


Gears Metric Racks

Hide Pictures

Go to Top  


Gears - Racks - Module 0.3

Gears - Racks - Module 0.3

20o Pressure Angle. Brass.

Metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Gear Racks


Gears - Racks - Module 0.4

Gears - Racks - Module 0.4

20o Pressure Angle. Brass, carbon steel and nylon.

Plastic and metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Gear Racks


Gears - Racks - Module 0.5

Gears - Racks - Module 0.5

20o Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.

Plastic and metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Gear Racks


Gears - Racks - Module 0.8

Gears - Racks - Module 0.8

20o Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.

Plastic and metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Gear Racks


Gears - Racks - Module 1.5

Gears - Racks - Module 1.5

20o Pressure Angle. Carbon steel, stainless steel, acetal and nylon.

Plastic and metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Gear Racks


Gears - Racks - Module 2.5

Gears - Racks - Module 2.5

20o Pressure Angle. Carbon steel, acetal and nylon.

Plastic and metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Gear Racks


Gears Metric Spur

Hide Pictures

Go to Top  


Gears - Spur - Module 0.15

Gears - Spur - Module 0.15

PCD = No. of Teeth x 0.150mm. 20o Pressure Angle. Brass.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears - Spur - Module 0.25

Gears - Spur - Module 0.25

PCD = No. of Teeth x 0.250mm. 20o Pressure Angle. Brass and carbon steel.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears - Spur - Module 0.75

Gears - Spur - Module 0.75

PCD = No. of Teeth x 0.750mm. 20o Pressure Angle. Brass.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears - Spur - Module 1.25

Gears - Spur - Module 1.25

PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel and acetal.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears Imperial Racks

Hide Pictures

Go to Top  


Gears - Racks -  1/10 Pitch

Gears - Racks - 1/10 Pitch

20o Pressure Angle. 416 Stainless Steel.

Metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Imperial Gear Racks


Gears - Racks -  1/20 Pitch

Gears - Racks - 1/20 Pitch

20o Pressure Angle. 416 Stainless Steel.

Metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Imperial Gear Racks



Select all items starting with...
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9



Store - Categories Pages

Go to Top





Store Pages

Go to Top





Main Pages on Small Parts and Bearings Website




Go to Top

Site Summary:

Freight Rates
Terms and Conditions
Privacy Policy

Small Parts and Bearings offers 151117 products in 3564 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We ship by traceable courier only (no standard post) and we have excellent Freight Rates within Australia and worldwide.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts and Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts and Bearings 1997. All rights reserved.