All Items: Rectangular Bar - Categories


Bar

Hide Pictures

Go to Top  


Rectangular Bar - Aluminium

Rectangular Bar - Aluminium

Thin and thick Aluminum strip and rectangular profiles

Small sizes may not be perfectly straight.

Click for combined categories: All Rectangular Bar


Rectangular Bar - Brass

Rectangular Bar - Brass

Thin and thick brass strip and rectangular profiles

Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small sizes may not be perfectly straight.

Click for combined categories: All Rectangular Bar

Related Information:
See also Strip Brass for very thin strips


Magnets Alcomax

Hide Pictures

Go to Top  


Magnets - Alcomax - Rectangular Bar

Magnets - Alcomax - Rectangular Bar

No keepers


Click for combined categories: All Magnets

Click for combined categories: All Alcomax Magnets


Bungs

Hide Pictures

Go to Top  


Bungs - Rectangular

Bungs - Rectangular

Plastic bungs fit inside rectangular tube.

Other colours available on request. Minimum quantities will apply. Made from tough polyethylene.

Click for combined categories: All Bungs

Related Information:
Square Bungs


Tube and Tubing

Hide Pictures

Go to Top  


Tube - Rectangular - Brass

Tube - Rectangular - Brass

Rectangular hollow tubing.

Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Click for combined categories: All Metal Tube


Tube - Rectangular - Carbon Fibre

Tube - Rectangular - Carbon Fibre

High impact light weight carbon fibre hollow tubing for modelling.

Pultruded carbon fibre with a smooth epoxy coated finish.

Click for combined categories: All Non Metallic Tube


Mounts Rectangular

Hide Pictures

Go to Top  


Mounts - Rectangular - 2 Bolt

Mounts - Rectangular - 2 Bolt

Vibration dampening

Base : Steel. Isolator : Natural Rubber.

Click for combined categories: All Rectangular Mounts


Mounts - Rectangular - 4 Bolt

Mounts - Rectangular - 4 Bolt

Rectangular elastomer component bonded with two steel plates.

Low installation height provides good stability. Effectively isolates against horizontal and vertical vibrations. High deflection capacity in horiziontal direction whilst deflection is low in vertical. Oil and grease resistant. Meets OSHA anchoring standards. Ideal use in presses, blowers, pumps, vibrators, rolling mills, crushers etc.

Click for combined categories: All Rectangular Mounts


Keys and Keysteel

Hide Pictures

Go to Top  


Keysteel Lengths - Rectangular - Carbon Steel

Keysteel Lengths - Rectangular - Carbon Steel

Plain carbon steel keysteel

Manufactured slightly oversize to prevent machine backlash. Zinc plating may be silver or gold in colour.

Click for combined categories: All Keysteel Lengths


Keysteel Lengths - Rectangular - Stainless Steel

Keysteel Lengths - Rectangular - Stainless Steel

303, 304 and 316

Manufactured slightly oversize to prevent machine backlash. Zinc plating may be silver or gold in colour.

Click for combined categories: All Keysteel Lengths


Keysteel Lengths - Rectangular - Zinc Plated

Keysteel Lengths - Rectangular - Zinc Plated

Zinc plated carbon steel

Manufactured slightly oversize to prevent machine backlash. Zinc plating may be silver or gold in colour.

Click for combined categories: All Keysteel Lengths


Suspension Units

Hide Pictures

Go to Top  


Suspension Units - Rubber - Rectangular - Bolt On

Suspension Units - Rubber - Rectangular - Bolt On

Housing (up to DOA45): Light Alloy (DOA50): spheroidal graphite cast iron. Rubber: Black, hardness 70 Shore A. Inner square section: Steel tube for mounting plug-in lever arms on one or both sides. All metal parts are paint-finished. Maximum Working Angle: +/-30oC / Operating Temperature Range: -40oC to +80oC.

Click for combined categories: All Suspension Units


Suspension Units - Rubber - Rectangular - Insert Type

Suspension Units - Rubber - Rectangular - Insert Type

Housing (up to DOS45): Light Alloy (DOS50): spheroidal graphite cast iron. Rubber: Black, hardness 70 Shore A. Inner square section: Steel tube for mounting plug-in lever arms on one or both sides. All metal parts are paint-finished. Maximum Working Angle: +/-30oC / Operating Temperature Range: -40oC to +80oC.

Click for combined categories: All Suspension Units


Balsa

Hide Pictures

Go to Top  


Balsa Wood - Block

Balsa Wood - Block

Rectangular and square section short lengths.

This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only. A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.

Balsa Wood - Rectangle

Balsa Wood - Rectangle

Rectangular section in longer lengths 900mm plus. See block for short lengths.

This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only. A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.

Hooks

Hide Pictures

Go to Top  


Tie Downs - Recessed

Tie Downs - Recessed

Works as a grapple or lifting ring with 90o stop. Mounts into a 79x87mm rectangular opening.

Zinc plated steel.

Latches

Hide Pictures

Go to Top  


Latches - Paddle

Latches - Paddle

Push to close latch accommodates left or right side latching. Corrosion resistant polycarbonate / ABS black resin housing and paddle. Paddle serves as door handle.

Quick easly installation into 36.8mm x 84.6mm rectangular hole. Lock plug is glass reinforced acetal with brass wafers. Other parts are glass reinforced nylon. Key lockable with locked/unlocked indicator. Keys are brass. Two 4.2x1.4mm self tapping screws supplied. Total grip left or right is 6.35mm. Max working load 50kg.

Magnets Rubber and Vinyl

Hide Pictures

Go to Top  


Materials - Magnetic Sheeting

Materials - Magnetic Sheeting

Magnetic sheeting is ideal for making small decorative magnets or for use on vehicles.

If cared for properly this magnetic material will not damage paintwork. Magnets should be removed weekly and the vehicle washed before re-applying. Type 1: White on one side and magnetic on the other. Ordered per metre. Type 2: Rectangular sheets sticky on one side and magnetic on the other. Sheeting will be supplied in one length up to the max continuous length shown in the tables.

Click for combined categories: All Materials

Click for combined categories: All Modelling Materials


Bar

Hide Pictures

Go to Top  


Bar - H Section - Brass

Bar - H Section - Brass


Bar - I Beam - Brass

Bar - I Beam - Brass


Hexagonal Bar - 303 Stainless

Hexagonal Bar - 303 Stainless

Corrosion resistant 303 grade stainless.

Saw Cut Ends. Small A/F sizes may not be perfectly straight.

Click for combined categories: All Hexagonal Bar


Hexagonal Bar - Brass

Hexagonal Bar - Brass

Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small A/F sizes may not be perfectly straight.

Click for combined categories: All Hexagonal Bar


Hexagonal Bar - Carbon Steel

Hexagonal Bar - Carbon Steel

Saw Cut Ends. Small A/F sizes may not be perfectly straight.

Click for combined categories: All Hexagonal Bar


Square Bar - 303 Stainless

Square Bar - 303 Stainless

Corrosion resistant 303 grade stainless.

Saw Cut Ends. Smaller sizes may not be supplied straight.

Click for combined categories: All Square Bar


Square Bar - Brass

Square Bar - Brass

Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Smaller sizes may not be supplied straight.

Click for combined categories: All Square Bar


Square Bar - Carbon Steel

Square Bar - Carbon Steel

Saw Cut Ends. Smaller sizes may not be supplied straight.

Click for combined categories: All Square Bar


Square Bar - Urethane

Square Bar - Urethane

Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Length +/- 2 percent.

Click for combined categories: All Square Bar


Magnets Alnico

Hide Pictures

Go to Top  


Magnets - Alnico - Bar

Magnets - Alnico - Bar

Cast Alnico 5 bar


Click for combined categories: All Magnets

Click for combined categories: All Alnico Magnets


Magnets Alcomax

Hide Pictures

Go to Top  


Magnets - Alcomax - Cylindrical Bar

Magnets - Alcomax - Cylindrical Bar

No keepers


Click for combined categories: All Magnets

Click for combined categories: All Alcomax Magnets


Shafting General Purpose

Hide Pictures

Go to Top  


Shafting - Keyed

Shafting - Keyed

Keyways are cut full length of each bar.

Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00.

Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting


Tools Threading

Hide Pictures

Go to Top  


Tools - Die Holders

Tools - Die Holders

Bar and round holders. 16mm, 20.64mm and 25.4mm (inch).

Click for combined categories: All Tools


Bar

Hide Pictures

Go to Top  


Tool Steel - 496 Oil Hardening - Flat Stock

Tool Steel - 496 Oil Hardening - Flat Stock

General purpose tool steel with good wear resistance, durability and machinability

Dimensionally stable chromium, tungsten and vanadium electric furnace toolsteel can be used for intricate work. Low 787 to 815 oC (1450-1500 F) hardening range makes it easy to harden. Fully spheroidised and annealed for uniform carbide size and easy machining. Each piece is individually wrapped and clearly marked with size, analysis and correct hardness and tempering information. Edge squareness 0.003 mm per mm. Finish is 0.0008mm (0.000032 inch).

Tools Threading

Hide Pictures

Go to Top  


Tools - Tap Wrenches

Tools - Tap Wrenches

Tee handle and bar types. Suit taps from 1mm to 12mm.

Click for combined categories: All Tools


Allthread

Hide Pictures

Go to Top  


Studs - Full Thread - Steel

Studs - Full Thread - Steel

Low Carbon Steel Allthread Threaded Bar

Lengths of Threaded Low Carbon Steel Bar.

Click for combined categories: All Studs


Latches

Hide Pictures

Go to Top  


Latches - Snap Slide

Latches - Snap Slide

Used for attaching subplates and assemblies. The sliding bar is attached to the removable panel and the post is mounted to the stationary support.

In the closed position the spring action of the bar resists opening under vibration and shock load. The removable panel thickness must be between 1.2 and 4.0mm. Spacers may be needed and are included with each latch. The post can be attached with rivets, screw and nut or wood screw. Each comes with post and bar assembly. Made from zinc plated steel with chromate finish.

Allthread

Hide Pictures

Go to Top  


Studs - Full Thread - Stainless Steel

Studs - Full Thread - Stainless Steel

18-8 Stainless Steel Allthread Threaded Bar

Lengths of Threaded 18-8 Stainless Steel Bar.

Click for combined categories: All Studs


Pulley Blocks

Hide Pictures

Go to Top  


Pulleys - Blocks - Eye - Swivel

Pulleys - Blocks - Eye - Swivel

Steel side plates. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.

Click for combined categories: All Pulley Blocks


Pulleys - Blocks - Flat

Pulleys - Blocks - Flat

Steel side plates with drop forged hooks. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.

Click for combined categories: All Pulley Blocks


Pulleys - Blocks - Eye - Fixed

Pulleys - Blocks - Eye - Fixed

Steel side plates with drop forged hooks. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.

Click for combined categories: All Pulley Blocks


Latches

Hide Pictures

Go to Top  


Latches - Barrel Bolts - 304 Stainless

Latches - Barrel Bolts - 304 Stainless

Barrel bolt, body and plates are made from 304 stainless steel. Bolt and knob are nickel plated brass. Simply lift the knob, slide it over and drop it into notch for secure latching.

Saitn finish. Attractive and ideal for corrosive environments.

Hoist Rings

Hide Pictures

Go to Top  


Rings - Hoist - Bar-Tite -tm-

Rings - Hoist - Bar-Tite -tm-

Range of movement 180o pivot, 360o swivel.

High tensile alloy steel. 100 percent magnetic particle inspected. Safety factor minimum 5 to 1. Black oxide finish per Mil C-13924B. Certified heat treatment.

Click for combined categories: All Hoist Rings


Handles

Hide Pictures

Go to Top  


Handles - Clean Line - Style 2

Handles - Clean Line - Style 2

High impact strength special technopolymer, in white similar to RAL 9002 with bright finish. Resistant to solvents, oils, greases and other chemical agents. Push fitting on plain shaft made from standard h9 tolerance bright drawn stock bars. Elastic coupling: the handle is not affected by vibrations and does not tend to loosen.

Click for combined categories: All Handles


Springs Compression

Hide Pictures

Go to Top  


Springs - Drawbar - Stainless Steel

Springs - Drawbar - Stainless Steel

Drawbar springs have long steel loops that pass through the centre of the spring and hook around the opposite end, compressing the spring on loading.

This design helps prevent unexpected overloading and fracturing that can occur in standard extension springs by stopping and hold the load at the spring limit. The spring rate indicates the load required to pull out the first 25mm of the spring.

Click for combined categories: All Drawbar Springs


Springs - Drawbar - Zinc Plated

Springs - Drawbar - Zinc Plated

Drawbar springs have long steel loops that pass through the centre of the spring and hook around the opposite end, compressing the spring on loading.

This design helps prevent unexpected overloading and fracturing that can occur in standard extension springs by stopping and hold the load at the spring limit. The spring rate indicates the load required to pull out the first 25mm of the spring.

Click for combined categories: All Drawbar Springs


Bearings for Wheelbarrows

Hide Pictures

Go to Top  


Bearings - Unground

Bearings - Unground

Unground bearings used in trolleys, prams and wheel barrow wheels


Lifting Chain

Hide Pictures

Go to Top  


Chain - Straight Link - Coil

Chain - Straight Link - Coil

Welded chain esily identified by it's long narrow link design. Used for tailgates, trailer safety and barrier chain. Not for lifting.

Low carbon steel with zinc plated, hot dip galvanised finish.

Click for combined categories: All Link Chain


Latches

Hide Pictures

Go to Top  


Latches - Cabinet - Low Profile

Latches - Cabinet - Low Profile

Designed mainly for use on light cabinet doors and panels. A distinctive snap lets user know the latch is fully open or closed. Plug barrel and hex nuts are zinc diecast.

Cam, lock washer and screw are made from steel with a nickel plated finish. Hex type accepts 6.35mm (1/4 inch) hex tool. For use on panels up to 6.35mm (1/4 in.) thick. Straight cams.

Shafting General Purpose

Hide Pictures

Go to Top  


Shafting - Mild Steel

Shafting - Mild Steel

Great axles for low load and low precision applications like trolleys, carts and wheelbarrows.


Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting

Related Information:
Shaft Extenders

Bore Reducers


Rod - Drill Blanks

Rod - Drill Blanks

Made of hardened high speed steel.

Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.

Click for combined categories: All Drill Rod


Rod - Drill - General

Rod - Drill - General

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Chrome vanadium alloy with unfinished ends. Requires heat treating to harden. Small diameters may not be perfectly straight. Heat treating by air, water or oil.

Click for combined categories: All Drill Rod

Related Information:
Silversteel


Rod - Drill - A-2 Air Hardening

Rod - Drill - A-2 Air Hardening

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Air hardening. Maximum abrasion resistance. 65 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Click for combined categories: All Drill Rod


Rod - Drill - O-1 Oil Hardening

Rod - Drill - O-1 Oil Hardening

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Click for combined categories: All Drill Rod


Rod - Drill - Oil Hardening - 480 Series

Rod - Drill - Oil Hardening - 480 Series

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

General purpose tool steel with good wear resistance, toughness and machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Click for combined categories: All Drill Rod


Rod - Drill - S-7 Air Hardening

Rod - Drill - S-7 Air Hardening

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Air hardening molybdenum, chromium, shock resisting. High impact strength with moderate wear resistance. 95 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Click for combined categories: All Drill Rod


Rod - Drill - W-1 Water Hardening

Rod - Drill - W-1 Water Hardening

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

High abrasion resistance and high toughness when hardened. 100 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Click for combined categories: All Drill Rod


Shafting - Ground - Silver Steel

Shafting - Ground - Silver Steel

Unhardened silversteel shafting for general purposes. Not suitable for precision bearings until machined to correct tolerances and hardened.

See also drill rod. Drill Rod.

Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting

Related Information:
Shaft Extenders

Bore Reducers


Bungs

Hide Pictures

Go to Top  


Bungs and Caps - Reversible - Round

Bungs and Caps - Reversible - Round

Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.

Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges.

Click for combined categories: All Bungs

Related Information:
Round Bungs


Square Shaft

Hide Pictures

Go to Top  


Shafting - Linear - Square

Shafting - Linear - Square


Shafting Precision Ground

Hide Pictures

Go to Top  


Shafts - Idler

Shafts - Idler

Ready made precision ground idler shafts.

Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design.

Shafts - Pinion

Shafts - Pinion


Click for combined categories: All Shafts


Splined Shafts and Bushes

Hide Pictures

Go to Top  


Splined Shafts - Stainless Steel

Splined Shafts - Stainless Steel

Externally splined shafting. Bushes not included. Match with same size splined bushes.

Match bushes and shafts by Major Diameter. Steel on Steel is not meant for sliding applications. Steel on Bronze is OK for intermittent sliding under load.

Click for combined categories: All Splined Shafts

Related Information:
Combined Splined Bushes List


Splined Shafts - Steel

Splined Shafts - Steel

Externally splined shafting. Bushes not included. Match with same size splined bushes.

Match bushes and shafts by Major Diameter. Steel on Steel is not meant for sliding applications. Steel on Bronze is OK for intermittent sliding under load.

Click for combined categories: All Splined Shafts

Related Information:
Combined Splined Bushes List


Flexible Shaft

Hide Pictures

Go to Top  


Shafts - Flexible - Coupling Ends - Open - Mild Steel

Shafts - Flexible - Coupling Ends - Open - Mild Steel

Flexible shafting with coupling ends ready to attach to a fixed shaft.

1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm.

Click for combined categories: All Flexible Shaft

Related Information:
Remote Control Nomenclature


Shafts - Flexible - Coupling Ends - Open - Stainless Steel

Shafts - Flexible - Coupling Ends - Open - Stainless Steel

Flexible shafting with coupling ends ready to attach to a fixed shaft. 303 Stainless Steel.

1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm.

Click for combined categories: All Flexible Shaft

Related Information:
Remote Control Nomenclature


Shafting General Purpose

Hide Pictures

Go to Top  


Shafts - Flexible - Panel Mount - Cased

Shafts - Flexible - Panel Mount - Cased

See PDF file at bottom of internet page for Performance Data.

Click for combined categories: All Flexible Shaft

Related Information:
Remote Control Nomenclature


Shafts - Flexible - Panel Mount - Open

Shafts - Flexible - Panel Mount - Open

See PDF file at bottom of internet page for Performance Data.

Click for combined categories: All Flexible Shaft

Related Information:
Remote Control Nomenclature


Shafting Precision Ground

Hide Pictures

Go to Top  


Rail Supports - Without Shaft

Rail Supports - Without Shaft

For mounting of linear shafting.

Shafting sold separately. Support is made from aluminium.

Click for combined categories: All Shaft Supports

Related Information:
Linear Bearing in Housing

Linear Bearings


Rail Supports - With Shaft

Rail Supports - With Shaft

Includes linear shafting.

Includes shaft to h6 tolerances. Support is made from aluminium.

Click for combined categories: All Shaft Supports

Related Information:
Linear Bearings


Rail Supports - With Shaft - One Piece

Rail Supports - With Shaft - One Piece

One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.

Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments.

Click for combined categories: All Shaft Supports

Related Information:
Linear Bearings

Frelon Linear Bearings


Hobby Shafting

Hide Pictures

Go to Top  


Shafting - Ground - Hobby - Steel

Shafting - Ground - Hobby - Steel

Silversteel shafting for hobbies. Not suitable for precision bearings.

Suitable for use with plastic gears, bushes, couplings etc. Not recommended for use with precision steel or stainless steel bearings. Some sizes have special features such as serrations or small barbs (noted in description). Unground ends. Ideal for axles in robotic applications and educational projects.

Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting

Related Information:
Shaft Extenders

Shaft Assortments


Shafting Aluminium

Hide Pictures

Go to Top  


Shafting - Aluminium

Shafting - Aluminium

Drylin aluminium shafting is recommended for use with Igubal Drylin bearings or Frelon lined bearings only.

Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.

Click for combined categories: All Shafting

Click for combined categories: All Aluminium Shafting


Shafting - Pipe - Aluminium

Shafting - Pipe - Aluminium

Recommended for use with Igubal Drylin bearings only.

Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and Less than 9.

Click for combined categories: All Pipe Shaft

Click for combined categories: All Metal Tube


Shafting - Supported - Pre-Drilled - Aluminium

Shafting - Supported - Pre-Drilled - Aluminium

For Drylin Bearings.

Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and less than 9.

Click for combined categories: All Shafting

Click for combined categories: All Aluminium Shafting


Shafting Precision Ground

Hide Pictures

Go to Top  


Shafting - Ground - Cold Rolled Steel

Shafting - Ground - Cold Rolled Steel

Cold rolled steel with saw cut ends and smooth finish


Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Chrome Plated

Shafting - Ground - Precision - Chrome Plated

Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Hardened and recommended for use with precision bearings. Ends are not plated.


Shafting - Ground - Precision - Chrome Vanadium Alloy

Shafting - Ground - Precision - Chrome Vanadium Alloy

Precision ground shafting. Ck53 / Cf53 Chrome Vanadium Alloy. Hardened and recommended for use with precision bearings.


Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - High Carbon Steel

Shafting - Ground - Precision - High Carbon Steel

Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.


Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Stainless 17-4PH Grade Hardened

Shafting - Ground - Precision - Stainless 17-4PH Grade Hardened

Precision ground shafting. 17-4PH grade. Hardened and recommended for use with precision bearings.


Click for combined categories: All Shafting

Click for combined categories: All Stainless Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Stainless 303 Grade

Shafting - Ground - Precision - Stainless 303 Grade

Precision ground shafting.


Click for combined categories: All Shafting

Click for combined categories: All Stainless Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Stainless 316 Grade

Shafting - Ground - Precision - Stainless 316 Grade

Precision ground shafting.


Click for combined categories: All Shafting

Click for combined categories: All Stainless Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Stainless 416 Grade Hardened

Shafting - Ground - Precision - Stainless 416 Grade Hardened

Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.


Click for combined categories: All Shafting

Click for combined categories: All Stainless Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Stainless 420 Grade Hardened

Shafting - Ground - Precision - Stainless 420 Grade Hardened

Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.


Click for combined categories: All Shafting

Click for combined categories: All Stainless Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Stainless 440C Grade Hardened

Shafting - Ground - Precision - Stainless 440C Grade Hardened

Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.


Click for combined categories: All Shafting

Click for combined categories: All Stainless Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Titanium - Ti-Gr2/TA1

Shafting - Ground - Precision - Titanium - Ti-Gr2/TA1


Click for combined categories: All Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Titanium - Ti-Gr5/TC4

Shafting - Ground - Precision - Titanium - Ti-Gr5/TC4


Click for combined categories: All Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Pre Drilled and Tapped - High Carbon Steel

Shafting - Pre Drilled and Tapped - High Carbon Steel

For use with rail supports and open linear bearings

Straightness: 0.1 mm / mtr.

Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting


Shafting - Pre Drilled and Tapped - Stainless Steel Steel

Shafting - Pre Drilled and Tapped - Stainless Steel Steel

For use with rail supports and open linear bearings


Click for combined categories: All Shafting

Click for combined categories: All Stainless Shafting


Bearings Linear

Hide Pictures

Go to Top  


Bearings - Linear - Ball - Open

Bearings - Linear - Ball - Open

For running on shafts supported by a rail along their length.

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.

Click for combined categories: All Linear Ball Bearings


Shafting Precision Ground

Hide Pictures

Go to Top  


Supports - Block

Supports - Block

For linear shafting.

Material: Aluminium.

Click for combined categories: All Supports


Bearings Linear

Hide Pictures

Go to Top  


Bearings - Linear - Ball - Closed

Bearings - Linear - Ball - Closed

Standard closed type to run on standard 60HRC shafts with h6 tolerances

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.

Click for combined categories: All Linear Ball Bearings


Shafting Precision Ground

Hide Pictures

Go to Top  


Supports - Flanged Four Bolt

Supports - Flanged Four Bolt

For linear shafting.

Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.

Click for combined categories: All Supports


Supports - Flanged Two Bolt

Supports - Flanged Two Bolt

For linear shafting.

Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.

Click for combined categories: All Supports


Supports - Pedestal Two Bolt

Supports - Pedestal Two Bolt

For linear shafting.

Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.

Click for combined categories: All Supports


Knobs Ball

Hide Pictures

Go to Top  


Knobs - Ball - Knock On - Phenolic

Knobs - Ball - Knock On - Phenolic

Moulded from black phenolic resin.

Light Weight. Thermal insulating. Non corrosive. POK Type have a ribbed insert. Shaft should be 0 to 0.007 mm undersized for best results. 712 Type suit standard metric rod.

Click for combined categories: All Ball Knobs


Assortments

Hide Pictures

Go to Top  


Assortment Kits - Various

Assortment Kits - Various

Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Shim - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins


Bearings Linear

Hide Pictures

Go to Top  


Bearings - Linear - Ball - Adjustable

Bearings - Linear - Ball - Adjustable

Adjustable type allows you to vary the preload according to your application

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.

Click for combined categories: All Linear Ball Bearings


Bearings - Linear - Ball - Stainless Steel - Adjustable

Bearings - Linear - Ball - Stainless Steel - Adjustable

Adjustable type allows you to vary the preload according to your application

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.

Click for combined categories: All Linear Ball Bearings


Bearings - Linear - Ball - Stainless Steel - Closed

Bearings - Linear - Ball - Stainless Steel - Closed

Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.

Click for combined categories: All Linear Ball Bearings


Engineering and Hobby Rod

Hide Pictures

Go to Top  


Rod - Round - Soft Metal Packs

Rod - Round - Soft Metal Packs

For general hobby applications. This rod is annealed soft to make it easier to bend. Copper, brass and aluminium,

300mm lengths. Not recommended for heavy duty applications. For use with bearings we suggest you use items from the category - Shafting - Ground.

Click for combined categories: All Metal Rod


Shafting Hollow

Hide Pictures

Go to Top  


Shafting - Pipe - AISI52100 Steel

Shafting - Pipe - AISI52100 Steel

AISI 52100 Steel Hardened to HRC 58-62. Straightness 0.0003 mm / mm. Ideal for design weight reduction. Note! ID of pipe shaft may be up to 1mm undersize. Other lengths may be available on request however a surcharge for special sizing will apply and extended delivery times can be expected (if available).

Click for combined categories: All Pipe Shaft

Click for combined categories: All Metal Tube



Select all items starting with...
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9



Store - Categories Pages

Go to Top





Store Pages

Go to Top





Main Pages on Small Parts and Bearings Website




Go to Top

Site Summary

Freight Rates
Terms and Conditions
Privacy Policy

Small Parts and Bearings offers 154795 products in 3682 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer's risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts and Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts and Bearings 1997. All rights reserved.