Categories for: plastic balls
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.
Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Opaque White. Specific Gravity: 1.4.
Resists alkalies, weak acids and most organic solvents.
Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.
Resistance to weather and sunlight. Good abrasion resistance.
Diametrical tolerances typically +/- 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.
Excellent for liquid level float applications.
Tolerance and spherecity: up to and including 25.4mm diameter = +/-0.0508mm, over 25.4mm diameter +/-0.0762mm. Very resistant to most acids and alkalies. Excellent for liquid level float applications. Unpolished. Specific Gravity: 0.91.
No water absorption. Temperatures up to 288 Deg C.
Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 Deg C. Unpolished. Specific Gravity: 2.3.
Torlon™ 4301 Bearing Grade Balls. Grade 1.
Polyamide-imide (Torlon™) Balls. Rockwell Hardness (Method A): E86 or M109-119. Specific Gravity: 1.38. Colour: Brown Opaque.
Bearings - Acetal - with 302 Stainless Steel Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 302 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
Bearings - Acetal - with 316 Stainless Steel Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
Bearings - Acetal - with Glass Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
Balls - Ceramic - Silicon Nitride
Outstanding wear resistance. Good thermal and chemical resistance.
High hardness. High strength over a wide temperature range. High fracture toughness. Outstanding wear resistance. Good thermal and chemical resistance.
Outstanding wear resistance. Excellent thermal and chemical resistance.
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).
Hardness: Rockwell C: 60-70.
Tolerances available on request. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.
Balls - Stainless Steel - 304 Grade
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 Deg C.
Balls - Stainless Steel - 316 Grade
A4 Grade. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 Deg C.
Balls - Stainless Steel - 316L Grade
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
Balls - Stainless Steel - 440C Grade
Hardness: Rockwell C: 55-60.
Tolerances available on request. AISI440C Stainless Steel. Hardness: Rockwell C: 55-60.
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2.
Extreme hardness and wear resistance.
Tolerances available on request. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.
Pins - Ball Lock - Ball Handle
Quick release. Zinc plated C1144 steel pins with black plastic ball handles snd spring loaded balls. Quick alternative to cotter pins.
Joints - Ball and Socket - In Line - Heavy Duty
Bearing Design: Steel and Plastic
Angular Movement 30 Degrees.
Chain - Roller - Plastic - Simplex
Includes acetal, polyproylene and nylon. Miniature size from 3.1mm up to 12.7mm
Snap together construction - no joining links required.
Sprockets - 12.7mm Pitch x 3.3mm Tooth Width - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 1270033 steel chain (081-1 Narrow).
Sprockets - 12.7mm Pitch x 4.9mm Tooth Width - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 1270049 steel chain (083-1 Narrow).
Sprockets - 12.7mm Pitch x 7.75mm Tooth Width - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 12700775 steel chain (08B-1 BS). British Standard 08B - 1/2 inch.
Sprockets - 12.7mm Pitch x 7.85mm Tooth Width - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 12700785 plastic or steel chain (40-1 ASA).
Sprockets - 3.12mm Pitch x 1.47mm Tooth Width - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 0312 miniature plastic chain.
Sprockets - 3.75mm Pitch x 1.6mm Tooth Width - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 0375 miniature plastic or stainless chain.
Sprockets - 6.00mm Pitch x 2.6mm Tooth Width - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 0600 steel chain.
Sprockets - 6.35mm Pitch x 2.8mm Tooth Width - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 0635 plastic or steel chain (25-1 ASA). American Standard 25-1 - 1/4 inch.
Sprockets - 8.00mm Pitch x 2.8mm Tooth Width - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 0800 steel chain.
Sprockets - 9.53mm Pitch x 4.7mm Tooth Width - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 0953047 plastic or steel chain (35-1 ASA). American Standard 35-1 - 3/8 inch.
Sprockets - 9.53mm Pitch x 5.7mm Tooth Width - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 0953057 steel chain (06B BS). British Standard 06B - 3/8 inch.
Bushes - Plastic - X-Lube - Flanged
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
Bushes - Plastic - X-Lube - Unflanged
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
Knobs - Ball - Threaded - Wrench Flats and Knob-Lok
Unique Knob-Lok features a nylon locking element that resists vibration and prevents back-off
Perfect for high vibrational applications.
Bearings - Thrust - Ball - Retainer and Balls Only
Match with thrust washers of the same bore and OD.
Bearings - Ball - 304 Stainless Steel
Corrosion and Heat resistance - Non Magnetic - Unhardened.
Tolerances differ from standard bearing types - see below. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. ID +0.050 mm / -0.000 mm OD +0.000 mm / -0.030 mm Width +0.000 mm /- 0.120 mm. Low load, low speed applications requiring maximum corrosion resistance. Non Magnetic. Cages, balls, races and shields from AISI 304 Stainless Steel.
Bearings - Ball - 316 Stainless Steel
Food and Medical grade Stainless Steel - Non Hardenable.
Tolerances differ from standard bearing types - see below. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. ID +0.0762 mm / -0.000 mm OD +0.000 mm / -0.0762 mm Width +/- 0.127 mm. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races.
Used for handling large work in drill presses or band saw machines.
Placed between work and machine so work can be easily moved. Black Oxide finish with 9.525mm hardened steel balls. Balls are exposed both sides of sheet.
Knobs - Ball - Threaded - Polished or Raw Brass
CDA 360 Free Machining Brass
Polished balls are fully finished and suitable for decorative and display purposes.
Screws - Ball - 16mm Nuts - Pillow Block
Includes ball nut.
Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.
Screws - Ball - Economy - Rolled - Nut Only
Match with screw. Accuracy T7 50µm/300mm.
Steel 16 MnCr5 or 100Cr6. Size, length of screw and end bearing configurations will affect the resulting loads and speeds. Backlash 0.01 Percent of lead. Accuracy T7 50µm/300mm. Blank sleeve supplied in nut to retain balls. Do not remove without simultaneous assembly to screw.
Leadscrew Nuts - Metric - Round - Plastic - Nylon 6.6
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Black Nylon 6.6. Wear Measured by Weight Reduction: 1.94wt.-%. Test Conditions: Load Direction: Horizontal Shaft Material: Stainless Steel Load: 10kg. Test Conditions: Speed: 300Rpm Cycles: 10,000 Stroke: 160mm Lubrication: None. Maintenance free. Support higher loads. Dry running. Dirt resistance.
Screws - Ball - Precision - Miniature
Myonic precision ballscrew and nut assemblies.
Ground thread. Low starting and running torque. Backlash of only a few microns, optional zero backlash or preload of nuts.
Steel Races with Si3N4 Ceramic Balls
Bearings with steel races and ceramic balls. For standard bearings, the balls are usually one of the first components to show wear. Ceramic balls are harder than steel and do not wear as easily.
Bushes - Plastic - Clip - Bevelled Edge
M250 Polymer minus 40 Deg C to 80 Deg C (minus 40 Deg F to 176 Deg F)
Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight.
Bushes - Plastic - Clip - Double Flanged
For use with sheet metal
Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. M250 Polymer minus 40 Deg C to 80 Deg C (minus 40 Deg F to 176 Deg F).
Bushes - Plastic - Ertalyte TX - Flanged
Self lubricated, high mechanical strength, stiffness and hardness.
Specific Gravity 1.44 g/cm3. Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 76 Mpa. Hardness 94 Rockwell M. High mechanical strength, stiffness and hardness. Self lubricating.
Bushes - Plastic - Ertalyte TX - Unflanged
Self lubricated, high mechanical strength, stiffness and hardness.
Bushes - Plastic - Iglidur A200 - Flanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 deg C = 116 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur A200 - Unflanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 deg C = 116 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur A290 - Flanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 deg C = 250 Mpa. Hardness 88 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur A290 - Unflanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 deg C = 250 Mpa. Hardness 88 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur F - Flanged
Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.
Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 deg C = 260 Mpa. Hardness 84 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur F - Unflanged
Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.
Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 deg C = 260 Mpa. Hardness 84 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur G - Flanged
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur G - Unflanged
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur H370 - Flanged
Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.
Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 deg C = 135 Mpa. Hardness 82 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur H370 - Unflanged
Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.
Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 deg C = 135 Mpa. Hardness 82 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur H - Flanged
Underwater performance. High Temp. Chemical Resistance.
Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 deg C = 175 Mpa. Hardness 87 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur H - Unflanged
Underwater performance. High Temp. Chemical Resistance.
Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 deg C = 175 Mpa. Hardness 87 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur J - Flanged
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 deg C = 73 Mpa. Hardness 74 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur J - Unflanged
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 deg C = 73 Mpa. Hardness 74 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur M250 - Flanged
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 deg C = 112 Mpa. Hardness 79 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur M250 - Unflanged
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 deg C = 112 Mpa. Hardness 79 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur P - Flanged
Low water absorption. Low wear. Hgh load.
Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 deg C = 120 Mpa. Hardness 75 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur P - Unflanged
Low water absorption. Low wear. Hgh load.
Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 deg C = 120 Mpa. Hardness 75 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur Q - Flanged
Excellent wear resistance under high load. Resistant to dirt.
Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 deg C = 120 Mpa. Hardness 83 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur Q - Unflanged
Excellent wear resistance under high load. Resistant to dirt.
Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 deg C = 120 Mpa. Hardness 83 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur W300 - Flanged
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 deg C = 125 Mpa. Hardness 77 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.Too many choices?
You have selected to see ALL categories including any of the following words: plastic balls
|
| |||||||||||||||||||||||||
| Select all items starting with... | |||||||||||||||||||||||||
| A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | Or use the category search | ||||||||||||||||
|
| |||||||||||||||||||||||||
