Quick Delivery Items: Oil Seals - Categories


Oil Seals

Hide Pictures

Go to Top  


Oil Seals - Fluoroelastomer Rubber

Oil Seals - Fluoroelastomer Rubber

DIN 3760 - High Temperature and chemical resistance.

Operating Temp. Range: -20oC to +240oC. The rubber elastomer outer covering tolerates thermal expansion as well as roughness in the housing bore. Suitable for synthetic and hydraulic fluids, strong acids, steam, many chemicals and many alkalis.

Click for combined categories: All Oil Seals


Oil Seals - Nitrile Rubber

Oil Seals - Nitrile Rubber

DIN 3760 - General purpose grease and oil sealing. Note - metal cased and rubber cased seals may be interchanged at our discretion. If one or the other is specifivally required please let us know when ordering.

Operating Temp. Range: -30oC to +90oC. The rubber elastomer outer covering tolerates thermal expansion as well as roughness in the housing bore. Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids.

Click for combined categories: All Oil Seals


Tape

Hide Pictures

Go to Top  


Tape - Silicone Wrap

Tape - Silicone Wrap

Self fusing silicone wrapping tape for emergency repairs or general protection. Seals leaks. Permanent. Self Bonding. No adhesive. Supa Tape.

Resists Fuels, Oils, Acid, Solvent, Salt Water, Road Salt and UV Rays. Temp Range minus 50 oC to plus 260 deg C. Insulates 8000 Volts (per unstretched layer). Tensile Strength 700psi. Lasts for years with a permanent air tight and water tight seal. Some uses include emergency radiator hose repair, insulation for radioactive areas, garden hose repair, exhaust pipe repair, electrical insulation, tool grips, sporting grips, rope ends, air duct joints, wire bundles. Areas of use include outdoor, auto, marine, workshop, motorcycle, camper, hunting, fishing, farming, plumbing, corrosive areas.

Click for combined categories: All Tape


Seals and Sealing

Hide Pictures

Go to Top  


Seals - Flat Gasket - Rubber

Seals - Flat Gasket - Rubber

Neoprene and natural rubber gaskets for sealing doors and many other applications.

Meet NEMA 12 to NEMA 4X applications. Easy to install with self adhesive backing. Easily cut to size and shaped for many applications. Fibre backing helps to eliminate stretching and helps to maintain seal in position.

Seals - Trim - Push On - Vinyl and Rubber

Seals - Trim - Push On - Vinyl and Rubber

Weatherstrip and trim by simply pushing over raw edges.


Shafting General Purpose

Hide Pictures

Go to Top  


Rod - Drill - Oil Hardening - 480 Series

Rod - Drill - Oil Hardening - 480 Series

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

General purpose tool steel with good wear resistance, toughness and machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Click for combined categories: All Drill Rod


Seals and Sealing

Hide Pictures

Go to Top  


Grommets - Rubber - EPDM

Grommets - Rubber - EPDM

EPDM Rubber Grommets

50 +/-5 Durometer. Easy to install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses.

Click for combined categories: All Grommets - Rubber


Grommets - Rubber - Natural

Grommets - Rubber - Natural

Natural Rubber Grommets

50 +/-5 Durometer. Easy to Install. Good Vibration and Shock Controll. Protects Wire, Cable and Hoses.

Click for combined categories: All Grommets - Rubber


Bar

Hide Pictures

Go to Top  


Tool Steel - 496 Oil Hardening - Flat Stock

Tool Steel - 496 Oil Hardening - Flat Stock

General purpose tool steel with good wear resistance, durability and machinability

Dimensionally stable chromium, tungsten and vanadium electric furnace toolsteel can be used for intricate work. Low 787 to 815 oC (1450-1500 F) hardening range makes it easy to harden. Fully spheroidised and annealed for uniform carbide size and easy machining. Each piece is individually wrapped and clearly marked with size, analysis and correct hardness and tempering information. Edge squareness 0.003 mm per mm. Finish is 0.0008mm (0.000032 inch).

Bushings Spherical

Hide Pictures

Go to Top  


Bushings - Spherical - Steel - With Oil Hole

Bushings - Spherical - Steel - With Oil Hole

Steel

Compensates for axial loads and misalignment.

Click for combined categories: All Spherical Bushings


Seals and Sealing

Hide Pictures

Go to Top  


Grommets - Rubber - EPDM - Closed

Grommets - Rubber - EPDM - Closed

Closed EPDM Rubber Grommets

50 +/-5 Durometer. Dustproof with Approx 0.5mm thick Membrane. Easy to Install.

Click for combined categories: All Grommets - Rubber


Shafting General Purpose

Hide Pictures

Go to Top  


Rod - Drill - O-1 Oil Hardening

Rod - Drill - O-1 Oil Hardening

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Click for combined categories: All Drill Rod


Bearings Plates

Hide Pictures

Go to Top  


Sheet - Sintered Bronze

Sheet - Sintered Bronze

Oil impregnated porous bronze sheet.


Click for combined categories: All Sheet


Bushes Bronze

Hide Pictures

Go to Top  


Bushes - Bronze - Sintered - Flanged

Bushes - Bronze - Sintered - Flanged

Oil impregnated flanged sintered bronze bushes.

Precision items show an allowable Load Speed Rating in Newtons times RPM.

Click for combined categories: All Bronze Bushes

Click for combined categories: All Flanged Bronze Bushes


Bushes - Bronze - Sintered - Unflanged

Bushes - Bronze - Sintered - Unflanged

Oil impregnated sintered bronze bushes.

Precision items show an allowable Load Speed Rating in Newtons times RPM.

Click for combined categories: All Bronze Bushes

Click for combined categories: All Unflanged Bronze Bushes

Related Information:
Solid Bronze Bushes

Spherical OD Bushes


Tube and Tubing

Hide Pictures

Go to Top  


Tube - Round - Sintered Bronze

Tube - Round - Sintered Bronze

Oil impregnated sintered bronze tubing - self lubricating.

Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on ID to allow for machining. B438 grade 1, Type 2 - AMS4805-D. SAE 841 Type 1, Class A.

Click for combined categories: All Metal Tube


Bushes Bronze

Hide Pictures

Go to Top  


Bushes - Bronze - Spherical - Sintered

Bushes - Bronze - Spherical - Sintered

Spherical OD Oil Impregnated Sintered Bronze Bushes.

ID and OD oversized. Enquire if details required.

Click for combined categories: All Bronze Bushes

Click for combined categories: All Flanged Bronze Bushes


Bushes Steel

Hide Pictures

Go to Top  


Bushes - Stainless Steel and PTFE - Flanged

Bushes - Stainless Steel and PTFE - Flanged

Oil, acid, alkali and salt water resistant. Contains no lead. Particularly suited to food applications, flow meters and pumps in pharmaceutical applications, printing machines chemical engineering and seawater applications.

Operating Temperature -200o to 280o Celsuis. PTFE with oilfibre 0.01 to around 0.03mm. Porous bronze 0.2 to around 0.3mm. Stainless steel backing 0.7 to around 2.3mm. 140 N/mm2 dynamic load rating. 250 N/mm2 static. 60 N/mm2 Oscillating.

Click for combined categories: All Steel Bushes

Click for combined categories: All Flanged Steel Bushes


Bushes - Stainless Steel and PTFE - Unflanged

Bushes - Stainless Steel and PTFE - Unflanged

Oil, acid, alkali and salt water resistant. Contains no lead. Particularly suited to food applications, flow meters and pumps in pharmaceutical applications, printing machines chemical engineering and seawater applications.

Operating Temperature -200o to 280o Celsuis. PTFE with oilfibre 0.01 to around 0.03mm. Porous bronze 0.2 to around 0.3mm. Stainless steel backing 0.7 to around 2.3mm. 140 N/mm2 dynamic load rating. 250 N/mm2 static. 60 N/mm2 Oscillating.

Click for combined categories: All Steel Bushes

Click for combined categories: All Unflanged Steel Bushes


Adhesives

Hide Pictures

Go to Top  


Super Bonders

Super Bonders

Mercury, ZAP, Molytec, Loctite, Pacer, Pro Seal. Cyanoacrylate adhesives for quick bonding. Products for foam Kicker, wood, metals, rubber and plastics.


Click for combined categories: All Adhesives


Bushes Bronze

Hide Pictures

Go to Top  


Bushes - Bronze - Sintered - Unflanged - Oilite

Bushes - Bronze - Sintered - Unflanged - Oilite

Genuine Oilite oil impregnated sintered bronze bushes.

Genuine Oilite Sintered Bronze designed to be fitted in H7 housings and f7 shafts. Static Load: 50N per mm Sq. Dynamic Load: 15N per mm sq. Rec Speed Range: 0.3 mtr per second to 0.5 mtr per second. Limit one Pv factor no greater than 1.8 Pv (Pv= N per mm sq x mtr per second).

Click for combined categories: All Bronze Bushes

Click for combined categories: All Unflanged Bronze Bushes

Related Information:
Solid Bronze Bushes

Spherical OD Bushes


Bushes - Bronze - Sintered - Flanged - Oilite

Bushes - Bronze - Sintered - Flanged - Oilite

Genuine Oilite flanged oil impregnated sintered bronze bushes.

Genuine Oilite Sintered Bronze designed to be fitted in H7 housings and f7 shafts. Static Load: 50N per mm Sq. Dynamic Load: 15N per mm sq. Rec Speed Range: 0.3 mtr per second to 0.5 mtr per second. Limit one Pv factor no greater than 1.8 Pv (Pv= N per mm sq x mtr per second).

Click for combined categories: All Bronze Bushes

Click for combined categories: All Flanged Bronze Bushes


Bearings Automotive

Hide Pictures

Go to Top  


Bearings - Automotive - Trailer Wheel - Kits

Bearings - Automotive - Trailer Wheel - Kits

Front and rear wheel bearing and seal kits for popular box trailers, boat trailers and caravans


Washers Flat Metallic

Hide Pictures

Go to Top  


Washers - Flat - Sintered Bronze - Precision

Washers - Flat - Sintered Bronze - Precision

Flat thrust washers made from oil impregnated sintered bronze

Click for combined categories: All Flat Washers and Spacers - Metallic


Washers Thrust

Hide Pictures

Go to Top  


Washers - Thrust - DP4 Type

Washers - Thrust - DP4 Type

Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.

Operating Temperature -200o to 280o Celsius. Maximum load 250N per mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free.

Click for combined categories: All Thrust Washers


O-Rings

Hide Pictures

Go to Top  


O-Rings - Silicone Rubber

O-Rings - Silicone Rubber

High thermal resistance and cold flexibility.

Temperature Range: -70oC to +200oC. Good dialectric properties and resistance to ozone and oxygen attack. Retains flexibility at high and low temperatures. Poor strength and tear resistance. Poor resistance to oils, fuels, concentrated acids and alkalis, water and steam.

Click for combined categories: All O-Rings


Bushes Steel

Hide Pictures

Go to Top  


Bushes - Steel - DP4 - Split - Flanged

Bushes - Steel - DP4 - Split - Flanged

Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.

Operating Temperature -200o to 280o Celsius. Maximum load 250N/mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free.

Click for combined categories: All Steel Bushes

Click for combined categories: All Flanged Steel Bushes


Bushes - Steel - DP4 - Split - Unflanged

Bushes - Steel - DP4 - Split - Unflanged

Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.

Operating Temperature -200o to 280o Celsius. Maximum load 250N/mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free.

Click for combined categories: All Steel Bushes

Click for combined categories: All Unflanged Steel Bushes


Bushes Bronze

Hide Pictures

Go to Top  


Bushes - Bronze - Dri-Plane - Flanged

Bushes - Bronze - Dri-Plane - Flanged

Bronze bearings with a graphite-based dry lubricant built in.

Doesnt require oil or grease for lubrication, therefore, cleaner with no out gassing, can operate between -34 to 371 oC.

Click for combined categories: All Bronze Bushes

Click for combined categories: All Flanged Bronze Bushes


Plungers Ball

Hide Pictures

Go to Top  


Plungers - Ball - Threaded - Acetal Body and Ball

Plungers - Ball - Threaded - Acetal Body and Ball

Acetal resin based (POM) technopolymer, screwdriver slotted head. Resistant to solvents, oils, greases and other chemical agents.

Acetal resin based (POM) technopolymer, screwdriver slotted head. Resistant to solvents, oils, greases and other chemical agents. Technopolymer ball, stainless steel spring.

Click for combined categories: All Threaded Ball Plungers


Clutches

Hide Pictures

Go to Top  


Clutch Assemblies - Slip - Precision

Clutch Assemblies - Slip - Precision

Adjustable Torque range 360-3600 g.cm (5-50 oz.in).

303 Stainless Steel. Brake : Oil Impregnated Bronze. Use with hubless gears with 9.525 bore and 3.175 face width.

Click for combined categories: All Clutch Assemblies


Sealing Plugs

Hide Pictures

Go to Top  


Sealing Plugs - Stainless

Sealing Plugs - Stainless

The sealing plug is a safe, quick, leakproof and low cost method for sealing cross-drilled holes. It ensures peak performance with a comfortable safety margin even in extreme applications.

Sleeve: Stainless Steel DIN 1.4305, AISI 303. Ball: Bearing Steel, Heat Treated. Hardness: HB = 220.

Handles

Hide Pictures

Go to Top  


Handles - Clean Line - Style 2

Handles - Clean Line - Style 2

High impact strength special technopolymer, in white similar to RAL 9002 with bright finish. Resistant to solvents, oils, greases and other chemical agents. Push fitting on plain shaft made from standard h9 tolerance bright drawn stock bars. Elastic coupling: the handle is not affected by vibrations and does not tend to loosen.

Click for combined categories: All Handles


Latches

Hide Pictures

Go to Top  


Latches - 1/4 Turn -Tee Handle - Non Locking

Latches - 1/4 Turn -Tee Handle - Non Locking

Quarter turn latches. Nema 4 and IP65 rated. Supplied assembled. Includes housing, insert, rubber seal, gasket, hex nut and cam.

Heavy Duty. Grip range is approximate and calculated as the door flange with compressed gasket and cabinet flange. Black polyamide handle. The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.

Click for combined categories: All Quarter Turn Latches


Gearboxes Cross Axis

Hide Pictures

Go to Top  


Gearboxes - Cross Axis - 150 x  96 x  96 A

Gearboxes - Cross Axis - 150 x 96 x 96 A

Helical or Wormwheel Gears. 25mm Bores. E60 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Helical Gears and Worms : Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Worm Wheel : Aluminium Bronze (CA104 / AB2). Circlips : Steel (not plated). Bearing : Steel 2RS (Rubber seals fitted).

Click for combined categories: All Cross Axis Gearboxes

Related Information:
Output Shafts


Pulley Blocks

Hide Pictures

Go to Top  


Pulleys - Blocks - Eye - Swivel

Pulleys - Blocks - Eye - Swivel

Steel side plates. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.

Click for combined categories: All Pulley Blocks


Cam Followers

Hide Pictures

Go to Top  


Cam Followers - Roller Type - Stainless Steel

Cam Followers - Roller Type - Stainless Steel

Stainless steel roller type cam followers.

Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.

Click for combined categories: All Cam Followers


O-Rings

Hide Pictures

Go to Top  


O-Rings - Nitrile Rubber

O-Rings - Nitrile Rubber

General purpose.

Temperature Range: -30oC to +90oC. Nitrile: Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids.

Click for combined categories: All O-Rings


Knobs Star

Hide Pictures

Go to Top  


Knobs - Star - Female - Soft

Knobs - Star - Female - Soft

Special high impact strength black technopolymer, covered with soft-touch elastomer chemically bonded (hardness 70 Shore A). Resistant to solvents, oils, greases and other chemical agents. brass insert with tapped blind hole.

Click for combined categories: All Star Knobs


Pulley Blocks

Hide Pictures

Go to Top  


Pulleys - Blocks - Flat

Pulleys - Blocks - Flat

Steel side plates with drop forged hooks. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.

Click for combined categories: All Pulley Blocks


Pulleys - Blocks - Eye - Fixed

Pulleys - Blocks - Eye - Fixed

Steel side plates with drop forged hooks. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.

Click for combined categories: All Pulley Blocks


Leadscrews

Hide Pictures

Go to Top  


Leadscrew Nuts - Metric - Hexagonal - Metallic

Leadscrew Nuts - Metric - Hexagonal - Metallic

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.

Click for combined categories: All Leadscrew Nuts

Click for combined categories: All Metric Leadscrew Nuts

Related Information:
Metric Whirled Leadscrew


Leadscrew Nuts - Metric - Square - Metallic

Leadscrew Nuts - Metric - Square - Metallic

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.

Click for combined categories: All Leadscrew Nuts

Click for combined categories: All Metric Leadscrew Nuts

Related Information:
Metric Whirled Leadscrew


Tape

Hide Pictures

Go to Top  


Tape - Fiberglass - PTFE Coated

Tape - Fiberglass - PTFE Coated

Heat Sealer Tape

Non stick ptfe tape is resistant to abrasion, high temperature and chemicals. Commonly used on heatsealing machines, mould protection, packaging, automotive and electrical applications. Temperature range minus 73 oC to 260 oC (-100 to 500 Deg F). Less than 5 percent elongation.

Click for combined categories: All Tape


Housings with Integral Bearing

Hide Pictures

Go to Top  


Housings - Bearing - Pillow Block - Bronze Bearing

Housings - Bearing - Pillow Block - Bronze Bearing

Aluminium with 5 percent self aligning sintered bronze bearing.

Bearing: Bronze SAE 840 (oil impregnated). / Housing: Sintered Aluminium / Corrosion Resistant. Mating shaft recommendation: Min. hardening 100 HRB (Rockwell B). Max surface finish 16 RMS. Recommended shaft clearance is 0.013 - 0.038mm, using lower limit of bore tolerance. Maximum Load and Speed: The figure shown in the plain bearing data are maximums, for guidance only, and cannot be combined. The performance of a plain bearing is stated as a PV value, which is the product of a pressure and velocity.

Click for combined categories: All Housings with Integral Bearing


Engineering and Hobby Rod

Hide Pictures

Go to Top  


Rod - Round - Sintered Bronze

Rod - Round - Sintered Bronze

Sintered bronze is supplied oversized so it can be machine finished to the dimensions shown.

Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Oil impregnated porous bronze rod. Smaller diameters may not be supplied straight. B438 grade 1, Type 2 - AMS4805-D. SAE 841 Type 1, Class A.

Click for combined categories: All Metal Rod


Shafting General Purpose

Hide Pictures

Go to Top  


Rod - Drill - General

Rod - Drill - General

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Chrome vanadium alloy with unfinished ends. Requires heat treating to harden. Small diameters may not be perfectly straight. Heat treating by air, water or oil.

Click for combined categories: All Drill Rod

Related Information:
Silversteel


O-Rings

Hide Pictures

Go to Top  


O-Rings - Neoprene Rubber

O-Rings - Neoprene Rubber

Excellent resistance to ageing and weathering effects.

Temperature Range: -20oC to +100oC. Resistant to ozone and refrigeration chemicals such as freon 12 and 22. Moderate resistance to swelling in mineral oils, greases and water. Not resistant to aromatic compounds such as benzene, toulene, chlorinated hydrocarbons, esters, ethers or ketones.

Click for combined categories: All O-Rings


Locking Compounds

Hide Pictures

Go to Top  


Threadlockers

Threadlockers

ZAP, Molytec, Loctite, Pacer. Pipe sealant, low to high strength threadlockers. Hydraulic threadlocker. Wick-In. Stops threads loosening from vibration.


Click for combined categories: All Adhesives


O-Rings

Hide Pictures

Go to Top  


O-Rings - Cord

O-Rings - Cord

Nitrile, Fluoroelastomer and EPDM continuous length o-ring cord.

Nitrile: Temp Range: -30oC to +90oC / Fluoroelastomer: Temp Range -20oC to +240oC. Nitrile: Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Nitrile: Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids. Fluoroelastomer (Viton(R)): Suitable for synthetic and hydraulic fluids, strong acids, steam, many chemicals and many alkalis.

Lubricants General Purpose

Hide Pictures

Go to Top  


Lubricants - General

Lubricants - General

Various brands and types. Includes Inox, Lanox, Anti-Seize, Cutting Fluid, Chain Lube, Moly Lube, Food Grade Grease, PTFE Lubes, Silicone and more

Some items in this category are marked as only available for collection. Includes high temperature and food grade lubes. Battery Conditioner - Oils - Moisture Inhibitor - WD - Valve and Oring Lubricant.

Click for combined categories: All Lubricants


Bearings Thrust

Hide Pictures

Go to Top  


Bearings - Thrust - Roller - Cage and Rollers Only

Bearings - Thrust - Roller - Cage and Rollers Only

Washers and Rollers sold separately. Match cage and roller assembly with washers from the washers category.

Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.

Click for combined categories: All Roller Thrust Cages and Washers

Related Information:
Other Thrust Bearings

Precision Shafting To Suit Bearings


Bearings - Thrust - Roller - Washers

Bearings - Thrust - Roller - Washers

Washers and Rollers sold separately. Match washers with cage and roller assembly from the cage and roller assembly category.

Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.

Click for combined categories: All Roller Thrust Cages and Washers

Related Information:
Other Thrust Bearings

Precision Shafting To Suit Bearings


Clips

Hide Pictures

Go to Top  


R Clips - Double Coil - Steel

R Clips - Double Coil - Steel

Also known as internal hitch pins, bridge pins or humpback pins


Click for combined categories: All R Clips


R Clips - Single Coil - Stainless Steel

R Clips - Single Coil - Stainless Steel

Also known as internal hitch pins, bridge pins or humpback pins


Click for combined categories: All R Clips


R Clips - Single Coil - Steel

R Clips - Single Coil - Steel

Also known as internal hitch pins, bridge pins or humpback pins


Click for combined categories: All R Clips


Shim

Hide Pictures

Go to Top  


Shim and Foil - Aluminium

Shim and Foil - Aluminium

Includes listing on 6061-T6 Aluminium Sheet. Very thin to thick sizes.

NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Coloured shim is anodised. The colour is not removable. The colour is for identification purposes only.

Click for combined categories: All Shim


Shim and Foil - Brass

Shim and Foil - Brass

Brass shim sheet. From very thin foil to thick sizes.

NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Includes sheets and rolls. See Brass - Strip for thin strips.

Click for combined categories: All Shim

Related Information:
See Assortment Kits for Shim Assortments

See also Strip - Brass for thin strips


Shim and Foil - Copper

Shim and Foil - Copper

Shim sheet. Very thin foil to thick sizes.

NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.

Click for combined categories: All Shim


Shim and Foil - Phosphor Bronze

Shim and Foil - Phosphor Bronze

Shim sheet. Phosphor Bronze.

NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.

Click for combined categories: All Shim


Shim and Foil - Stainless Steel

Shim and Foil - Stainless Steel

Shim sheet. Very thin foil to thick sizes. Includes 416, 303 and 316 grades.

NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.

Click for combined categories: All Shim


Shim and Foil - Steel

Shim and Foil - Steel

Shim sheet. Cold rolled steel. Very thin to thick sizes.

NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.

Click for combined categories: All Shim


Bearings Linear

Hide Pictures

Go to Top  


Bushes - Aluminium - Frelon Lined - Flanged

Bushes - Aluminium - Frelon Lined - Flanged

Self lubricating - Replaces oilite or plastic bearings.

SLIP FIT: Housing bore should be nominal OD +0.050/+0.075 - lock in place with retaining compound or epoxy. PRESS FIT: Housing bore should be nominal OD -0.000/+0.012. Use freezing method for press fit assembly - freeze bearing to -18 oC for 30 minutes. Body: Aluminium. Lining: Frelon.

Click for combined categories: All Aluminium Bushes


Bushes - Aluminium - Frelon Lined - Unflanged

Bushes - Aluminium - Frelon Lined - Unflanged

Self lubricating - Replaces oilite or plastic bearings.

SLIP FIT: Housing bore should be nominal OD +0.050/+0.075 - lock in place with retaining compound or epoxy. PRESS FIT: Housing bore should be nominal OD -0.000/+0.012. Use freezing method for press fit assembly - freeze bearing to -18 oC for 30 minutes. Body: Aluminium. Lining: Frelon.

Click for combined categories: All Aluminium Bushes


Adhesives

Hide Pictures

Go to Top  


Adhesives - General

Adhesives - General

Molytec, Loctite, Pacer, Dow Corning, 3M. Includes silicone sealant, gasket adhesive, canopy glue, belt conditioner and electronic tak-pak.


Click for combined categories: All Adhesives


Leadscrews

Hide Pictures

Go to Top  


Leadscrews - Metric - Rolled Thread - Carbon Steel

Leadscrews - Metric - Rolled Thread - Carbon Steel

Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.

Carbon Steel C35. For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.

Click for combined categories: All Leadscrews

Click for combined categories: All Metric Leadscrews

Related Information:
Metric Nuts


Thread Inserts

Hide Pictures

Go to Top  


Inserts - Thread Repair - Recoil

Inserts - Thread Repair - Recoil

Recoil inserts are screwed directly into an enlarged tapped hole. Replacement inserts for your kit.

Stainless inserts. Replacement Individual Inserts - Require full kit to obtain correct tap. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.

Click for combined categories: All Recoil Inserts and Kits


Spring Wire

Hide Pictures

Go to Top  


Wire - Steel - Spring - Music - Coils

Wire - Steel - Spring - Music - Coils

SAE 1090 Spring Steel.


Click for combined categories: All Spring Wire


Plungers Ball

Hide Pictures

Go to Top  


Plungers - Ball - Threaded - Steel

Plungers - Ball - Threaded - Steel

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

Click for combined categories: All Threaded Ball Plungers


Plungers Spring

Hide Pictures

Go to Top  


Plungers - Spring - Threaded - Steel

Plungers - Spring - Threaded - Steel

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

Click for combined categories: All Threaded Spring Plungers


Plungers Ball

Hide Pictures

Go to Top  


Plungers - Ball - Threaded - 303 Stainless Steel

Plungers - Ball - Threaded - 303 Stainless Steel

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

Click for combined categories: All Threaded Ball Plungers


Plungers Spring

Hide Pictures

Go to Top  


Plungers - Spring - Knurled Handle - Locking - Steel

Plungers - Spring - Knurled Handle - Locking - Steel

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

Click for combined categories: All Threaded Spring Plungers

Click for combined categories: All Handled Spring Plungers


Plungers - Spring - Threaded - Stainless

Plungers - Spring - Threaded - Stainless

303 Stainless Steel.

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

Click for combined categories: All Threaded Spring Plungers


Plungers Ball

Hide Pictures

Go to Top  


Plungers - Ball - Threaded - Acetal Body with Stainless Ball

Plungers - Ball - Threaded - Acetal Body with Stainless Ball

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

Click for combined categories: All Threaded Ball Plungers


Clutches

Hide Pictures

Go to Top  


Clutches - Slip - Magnetic Particle - No Power

Clutches - Slip - Magnetic Particle - No Power

Requires no power.

Sealed from contamination. Uses permanent magnets and magnetic particles. Constant torque levels. Zero maintenance - Long operational life. See PDF sheet at bottom of this page.

Click for combined categories: All Slip Clutches


Insulators

Hide Pictures

Go to Top  


Insulators - Screw

Insulators - Screw

Nonconductive. Noncorrosive. Lightweight. Self-sealing. Self-locking.

Plungers Spring

Hide Pictures

Go to Top  


Plungers - Spring - Threaded - Steel/Acetal

Plungers - Spring - Threaded - Steel/Acetal

Acetal nose with steel body

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

Click for combined categories: All Threaded Spring Plungers


Clutches

Hide Pictures

Go to Top  


Clutches - Slip - Magnetic Particle - Integral Shaft - No Power

Clutches - Slip - Magnetic Particle - Integral Shaft - No Power

Requires no power.

Sealed from contamination. Uses permanent magnets and magnetic particles. Constant torque levels. Zero maintenance - Long operational life. See PDF sheet at bottom of this page.

Click for combined categories: All Slip Clutches


Plungers Ball

Hide Pictures

Go to Top  


Plungers - Ball - Threaded - Steel - Threadlock

Plungers - Ball - Threaded - Steel - Threadlock

With Long-Lok thread locking compound to prevent loosening

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

Click for combined categories: All Threaded Ball Plungers


Plungers Spring

Hide Pictures

Go to Top  


Plungers - Spring - Threaded - Steel - Threadlock

Plungers - Spring - Threaded - Steel - Threadlock

With Long-Lok thread locking compound to prevent loosening

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

Click for combined categories: All Threaded Spring Plungers


Gearboxes Right Angle

Hide Pictures

Go to Top  


Gearboxes - Right Angle - Model RA 0665-0508-0508 - 66.55 x 50.8 x 50.8mm

Gearboxes - Right Angle - Model RA 0665-0508-0508 - 66.55 x 50.8 x 50.8mm

1 to 1 ratio with rated speeds up to 1800rpm. Sealed gearcase. Key drive shafts. Keys included.

4140 Heat Treated steel gears and shafts. Aluminium alloy hard anodised case. Maximum operating temperature 90 oC (200 Deg F). Optional foot mount plates available - also listed in this category.

Click for combined categories: All Right Angle Gearboxes


Plungers Ball

Hide Pictures

Go to Top  


Plungers - Ball - Threaded - 303 Stainless Steel with Threadlock

Plungers - Ball - Threaded - 303 Stainless Steel with Threadlock

With Long-Lok thread locking compound to prevent loosening

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

Click for combined categories: All Threaded Ball Plungers


Gearheads Inline

Hide Pictures

Go to Top  


Gearheads - Inline - Planetary - Size  17 - Precision

Gearheads - Inline - Planetary - Size 17 - Precision

Use with NEMA Size 17 Motors.

Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).

Click for combined categories: All Inline Gearheads

Related Information:
Gear Types


Ball Transfers

Hide Pictures

Go to Top  


Ball Transfer Units - Screw Stem - Stainless

Ball Transfer Units - Screw Stem - Stainless

For conveying materials.

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.

Click for combined categories: All Ball Castors and Transfers

Click for combined categories: All Screw Fit Ball Transfers


Ball Transfer Units - Screw Stem - Steel

Ball Transfer Units - Screw Stem - Steel

For conveying materials.

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.

Click for combined categories: All Ball Castors and Transfers

Click for combined categories: All Screw Fit Ball Transfers


Packing Boxes and Materials

Hide Pictures

Go to Top  


Packing Materials

Packing Materials

A small selection of common packing materials. Boxes, markers, mailpacks, bubble wrap and magicseal bags.


Housings with Integral Bearing

Hide Pictures

Go to Top  


Housings - Bearing - Pillow Block - PTFE Bronze Bearing

Housings - Bearing - Pillow Block - PTFE Bronze Bearing

Aluminium with 5 percent self aligning sintered bronze bearing and PTFE solid lubricant.

Bearing: Bronze PTFE impregnated. / Housing: Sintered Aluminium / Corrosion Resistant. Mating shaft recommendation: Min. hardening 100 HRB (Rockwell B). Max surface finish 16 RMS. Recommended shaft clearance is 0.013 - 0.038mm, using lower limit of bore tolerance. Maximum Load and Speed: The figure shown in the plain bearing data are maximums, for guidance only, and cannot be combined. Operating temperature minus 201 to plus 282o Celsius (minus 330 to plus 540o Farenheit).

Click for combined categories: All Housings with Integral Bearing


Mounts Centrebolt

Hide Pictures

Go to Top  


Mounts - Centre Bolt - Solo Unitised

Mounts - Centre Bolt - Solo Unitised

Vibration dampening

Calculate static load and select a mount of equal or greater capacity. For dynamic loads of 3 x static load select the next larger size. Lubricate mount and socket with water or rubber lubricant. Insert into socket and hand rotate with axial force. Outer Body : Natural Rubber / Spacer : Rolled Tubular Steel.

Click for combined categories: All Centrebolt Mounts


Mounts - Centre Bolt - Tandem Unitised

Mounts - Centre Bolt - Tandem Unitised

Vibration dampening

Calculate static load and select a mount of equal or greater capacity. For dynamic loads of 3 x static load select the next larger size. Lubricate mount and socket with water or rubber lubricant. Insert into socket and hand rotate with axial force. Outer Body : Natural Rubber / Spacer : Rolled Tubular Steel.

Click for combined categories: All Centrebolt Mounts



Select all items starting with...
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9



Store - Categories Pages

Go to Top





Store Pages

Go to Top





Main Pages on Small Parts and Bearings Website




Go to Top

Site Summary

Freight Rates
Terms and Conditions
Privacy Policy

Small Parts and Bearings offers 155123 products in 3615 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We ship by traceable courier only (no standard post) and we have excellent Freight Rates within Australia and worldwide.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts and Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts and Bearings 1997. All rights reserved.