Couplings Helical and Slit
Low cost aluminium couplings primarily used for 3D printer stepper motors
Max. Ang Misalignment 5
o. Max Parallel Offset 0.25mm. This category may be available in the new MBA online store at
Couplings - Helical - Economy.
Related Information:
Offer 90% efficiency converting rotary to linear motion with low coefficient of friction. Match all components within the Thomson Saginaw range only.
When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C. This category may be available in the new MBA online store at
Ballscrew - Thomson Saginaw.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Related Information:
12 VDC - 12,300 RPM unloaded at 4.5 volts
Related Information:
6.0 VDC - 4,900 RPM unloaded at 4.5 volts
Related Information:
Our smallest motors at an affordable price.
Various models 10000 to 30000 rpm. Low starting voltage of Less than0.8V. Rated Voltage 1.3V. Less than 43 dB Mechanical Noise Level. 100 hours / 100000 turns mechanical life. Clockwise rotation when viewed from shaft end. Not recommended for reversing.
Related Information:
3.5V - 20500 RPM
Related Information:
Includes vibrating disc motor
Neoprene 60 durometer black ground outside diameter drive rollers
This category may be available in the new MBA online store at
Rollers - Drive.
Use with idler shafts and idler pulleys. Fixed base with adjustable arm through 360o.
Related Information:
Use with idler shafts and idler pulleys. With flanged base that can be mounted in a tight area.
Idler shaft and pulleys not included with tensioner. Rotating arm gives operator 360
o controlled tensioning. Serrated teeth to prevent slippage once tightened. This category may be available in the new MBA online store at
Tensioner - Drive - Adjustable Flanged.
Related Information:
Budget Assemblies. Average fatigue life of 5000 to 30000 cycles.
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
Related Information:
Used to replace screws where the need to remove the pin is unlikely.
Stainless Steel 304 Grade. Simple, low cost assembly. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
Related Information:
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Made from stress proof steel. The power drive tool is used for volume installation of EZ-LOK thread inserts.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench. This category may be available in the new MBA online store at
Inserts - Self Tapping - For Wood - Hex Drive.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench. This category may be available in the new MBA online store at
Inserts - Self Tapping - For Wood - Hex Drive - Flanged.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.
Related Information:
Threaded inserts are screwed into pre-formed or pre-drilled holes and cut their own threads. Perfect for permanent installations.
Made from brass. Install with a screwdriver. Superior holding power in hard and soft woods, particle board and other wood products. Long pilot assists with straight driving into a drilled hole. This category may be available in the new MBA online store at
Inserts - Self Tapping - For Wood - Slotted Drive - Short.
Flat Head Countersunk. Metric only. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Nuts sold seperately - See Nuts. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at
Screws - Countersunk - Titanium CP Grade 1 - Philips Drive.
Related Information:
Flat Head Countersunk. Metric only. CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.
Nuts sold seperately - See Nuts. Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance. This category may be available in the new MBA online store at
Screws - Countersunk - Titanium CP Grade 2 - Philips Drive.
Related Information:
Metal Thread Screws. Metric only. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Nuts sold seperately - See Nuts. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at
Screws - Pan Head - Titanium CP Grade 1 - Philips Drive.
Related Information:
Partially threaded metric slotted drive set screws - grub screws
Related Information:
Small light weight geared motors used in toys and small solar applications
NOTE! These do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications. This category may be available in the new MBA online store at
Gearmotors - Basic - Hobby - 12.1mm Diameter.
Blanks for cutting gears and pulleys and friction drives.
This category may be available in the new MBA online store at
Gears - Blanks.
Use with NEMA Size 17 Motors.
Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).
Related Information:
25mm Gearhead Body Diameter. 24.4mm Motor Body Diameter. Low cost. Reversible
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive. Use with GT2 or GT3 type belts.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive. Use with GT2 or GT3 type belts.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive. Use with GT2 or GT3 type belts.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive. Also known as LT.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.