Metric Worms And Gears - Small Parts And Bearings Categories


Gears Metric Worms

Hide Pictures

Go to Top  


Worm Gears - Module 3 (Series 1) - Metallic - Left Hand

Worm Gears - Module 3 (Series 1) - Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.92o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 3 (Series 1) - Metallic - Right Hand

Worm Gears - Module 3 (Series 1) - Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.92o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 1 (Series 2) - Plastic Gear and Metallic Worm

Worms - Module 1 (Series 2) - Plastic Gear and Metallic Worm

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 4.40o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 2 (Series 4) - Plastic Gear and Metallic Worm

Worms - Module 2 (Series 4) - Plastic Gear and Metallic Worm

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 4.40o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 1 (Series 2) - Plastic Gear and Metallic Worm

Worm Gears - Module 1 (Series 2) - Plastic Gear and Metallic Worm

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 4.40o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 2 (Series 4) - Plastic Gear and Metallic Worm

Worm Gears - Module 2 (Series 4) - Plastic Gear and Metallic Worm

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 4.40o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 1.5 (Series 1) - Plastic and Metallic - Left Hand

Worm Gears - Module 1.5 (Series 1) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.43o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 1.5 (Series 1) - Plastic and Metallic - Right Hand

Worm Gears - Module 1.5 (Series 1) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.43o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Left Hand

Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Right Hand

Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Left Hand

Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.87o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand

Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.87o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 2 (Series 3) - Plastic and Metallic - Left Hand

Worm Gears - Module 2 (Series 3) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.70o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 2 (Series 3) - Plastic and Metallic - Right Hand

Worm Gears - Module 2 (Series 3) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.70o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm

Worms - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm

Match with metallic worms Module 0.80 Series 2.

20o Pressure Angle - 4.40o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm

Worm Gears - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm

Match with metallic worms Module 0.80 Series 2.

20o Pressure Angle - 4.40o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Gears Imperial Worms

Hide Pictures

Go to Top  


Worm Gears - 24 Diametrical Pitch (Series 1) - Plastic

Worm Gears - 24 Diametrical Pitch (Series 1) - Plastic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.77o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 24 Diametrical Pitch (Series 2) - Plastic

Worm Gears - 24 Diametrical Pitch (Series 2) - Plastic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 9.47o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 32 Diametrical Pitch (Series 1) - Plastic

Worm Gears - 32 Diametrical Pitch (Series 1) - Plastic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 32 Diametrical Pitch (Series 2) - Plastic

Worm Gears - 32 Diametrical Pitch (Series 2) - Plastic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 8.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 48 Diametrical Pitch (Series 1) - Plastic

Worm Gears - 48 Diametrical Pitch (Series 1) - Plastic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 48 Diametrical Pitch (Series 3) - Plastic

Worm Gears - 48 Diametrical Pitch (Series 3) - Plastic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 7.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 24 Diametrical Pitch (Series 1) - Metallic

Worm Gears - 24 Diametrical Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.77o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 24 Diametrical Pitch (Series 2) - Metallic

Worm Gears - 24 Diametrical Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 9.47o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 24 Diametrical Pitch (Series 3) - Metallic

Worm Gears - 24 Diametrical Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 18.43o Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 32 Diametrical Pitch (Series 1) - Metallic

Worm Gears - 32 Diametrical Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 32 Diametrical Pitch (Series 2) - Metallic

Worm Gears - 32 Diametrical Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 8.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 32 Diametrical Pitch (Series 3) - Metallic

Worm Gears - 32 Diametrical Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 15.95o Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 48 Diametrical Pitch (Series 1) - Metallic

Worm Gears - 48 Diametrical Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 3.35o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 48 Diametrical Pitch (Series 2) - Metallic

Worm Gears - 48 Diametrical Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 48 Diametrical Pitch (Series 3) - Metallic

Worm Gears - 48 Diametrical Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 7.7o Lead Angle - 2 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 48 Diametrical Pitch (Series 4) - Metallic

Worm Gears - 48 Diametrical Pitch (Series 4) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 8.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 48 Diametrical Pitch (Series 5) - Metallic

Worm Gears - 48 Diametrical Pitch (Series 5) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 14.2o Lead Angle - 4 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 48 Diametrical Pitch (Series 6) - Metallic

Worm Gears - 48 Diametrical Pitch (Series 6) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 14.2o Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 64 Diametrical Pitch (Series 1) - Metallic

Worm Gears - 64 Diametrical Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 1.78o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 64 Diametrical Pitch (Series 2) - Metallic

Worm Gears - 64 Diametrical Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 3.58o Lead Angle - 2 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 64 Diametrical Pitch (Series 3) - Metallic

Worm Gears - 64 Diametrical Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 7.12o Lead Angle - 4 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Gears Metric Worms

Hide Pictures

Go to Top  


Worms - Module 3 (Series 1) - Metallic - Left Hand

Worms - Module 3 (Series 1) - Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.92o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 1 (Series 1) - Plastic and Metallic - Left Hand

Worms - Module 1 (Series 1) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 2 (Series 3) - Plastic and Metallic - Left Hand

Worms - Module 2 (Series 3) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.70o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 1.5 (Series 1) - Plastic and Metallic - Left Hand

Worms - Module 1.5 (Series 1) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.43o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 1.5 (Series 1) - Plastic and Metallic - Right Hand

Worms - Module 1.5 (Series 1) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.43o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 1 (Series 1) - Plastic and Metallic - Right Hand

Worms - Module 1 (Series 1) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 2.5 (Series 1) - Plastic and Metallic - Left Hand

Worms - Module 2.5 (Series 1) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.87o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand

Worms - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.87o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 2 (Series 3) - Plastic and Metallic - Right Hand

Worms - Module 2 (Series 3) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.70o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Hobby Gears

Hide Pictures

Go to Top  


Hobby Gears - Worm and Wheel  40 : 1 Plastic

Hobby Gears - Worm and Wheel 40 : 1 Plastic

Popular Hobby Set

1 start 40 tooth gear.

Pins - Taper

Hide Pictures

Go to Top  


Pins - Taper - Metric

Pins - Taper - Metric

Metric Sizes 1:50 Taper

Metric Sizes to DIN 1.

Click for combined categories: All Metric Taper Pins

Related Information:
Miniature Imperial Taper Pin Sizes


Nuts

Hide Pictures

Go to Top  


Nuts - Hexagonal - Steel - Class 8 Metric

Nuts - Hexagonal - Steel - Class 8 Metric

Metric property class 8. Zinc chromate plate with red dye for easy identification. Meets or exceeds ANSI/ASME B18.2.4.1 standards.


Click for combined categories: All Nuts


Leadscrews

Hide Pictures

Go to Top  


Leadscrew Nuts - Metric - Flanged - Bronze

Leadscrew Nuts - Metric - Flanged - Bronze

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Bronze CuSn8P. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil. Manual or powered control - Low and medium rotational speeds - For working under load. 6 Mounting Holes On Flange.

Click for combined categories: All Leadscrew Nuts

Click for combined categories: All Metric Leadscrew Nuts

Related Information:
Metric Rolled Leadscrew

Metric Whirled Leadscrew


Leadscrew Nuts - Metric - Flanged - Plastic

Leadscrew Nuts - Metric - Flanged - Plastic

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Iglidur W300. Single Start / Right Hand.

Click for combined categories: All Leadscrew Nuts

Click for combined categories: All Metric Leadscrew Nuts

Related Information:
Metric Rolled Leadscrew

Metric Whirled Leadscrew


Leadscrew Nuts - Metric - Hexagonal - Metallic

Leadscrew Nuts - Metric - Hexagonal - Metallic

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.

Click for combined categories: All Leadscrew Nuts

Click for combined categories: All Metric Leadscrew Nuts

Related Information:
Metric Whirled Leadscrew


Leadscrew Nuts - Metric - Round - Metallic

Leadscrew Nuts - Metric - Round - Metallic

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.

Click for combined categories: All Leadscrew Nuts

Click for combined categories: All Metric Leadscrew Nuts

Related Information:
Metric Whirled Leadscrew


Leadscrew Nuts - Metric - Square - Metallic

Leadscrew Nuts - Metric - Square - Metallic

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.

Click for combined categories: All Leadscrew Nuts

Click for combined categories: All Metric Leadscrew Nuts

Related Information:
Metric Whirled Leadscrew


Leadscrew Nuts - Metric - Round - Plastic - Nylon 6.6

Leadscrew Nuts - Metric - Round - Plastic - Nylon 6.6

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Black Nylon 6.6. Wear Measured by Weight Reduction: 1.94wt.-%. Test Conditions: Load Direction: Horizontal Shaft Material: Stainless Steel Load: 10kg. Test Conditions: Speed: 300Rpm Cycles: 10,000 Stroke: 160mm Lubrication: None. Maintenance free. Support higher loads. Dry running. Dirt resistance.

Click for combined categories: All Leadscrew Nuts

Click for combined categories: All Metric Leadscrew Nuts

Related Information:
Metric Whirled Leadscrew


Leadscrews - Metric - Rolled Thread - Carbon Steel

Leadscrews - Metric - Rolled Thread - Carbon Steel

Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.

Carbon Steel C35. For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.

Click for combined categories: All Leadscrews

Click for combined categories: All Metric Leadscrews

Related Information:
Metric Nuts


Leadscrews - Metric - Rolled Thread - Stainless Steel

Leadscrews - Metric - Rolled Thread - Stainless Steel

Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.

Stainless steel 316L. For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.

Click for combined categories: All Leadscrews

Click for combined categories: All Metric Leadscrews

Related Information:
Metric Nuts


Leadscrews - Metric - Whirled Thread - Carbon Steel

Leadscrews - Metric - Whirled Thread - Carbon Steel

Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.

Longer lengths may be available on request. Single Start. Steel 080 M40 (ck40). Whirled screw left hand and right hand cut on same single piece of material to DIN103 Grade 7e. Use with Trapezoidal Nuts.

Click for combined categories: All Leadscrews

Click for combined categories: All Metric Leadscrews

Related Information:
Metric Nuts


Leadscrews - Metric - Whirled Thread - Stainless Steel

Leadscrews - Metric - Whirled Thread - Stainless Steel

Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.

Longer lengths may be available on request. Single Start. 303 Stainless Steel. Whirled screw left hand and right hand cut on same single piece of material to DIN103 Grade 7e. Use with Trapezoidal Nuts.

Click for combined categories: All Leadscrews

Click for combined categories: All Metric Leadscrews

Related Information:
Metric Nuts


Timing Belts and Pulleys 5.0mm

Hide Pictures

Go to Top  


Belts - Timing -  5.000mm Pitch - GT - TRUE METRIC - 15mm Wide

Belts - Timing - 5.000mm Pitch - GT - TRUE METRIC - 15mm Wide

GT Series Metric Timing Belts.

Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.93mm. Belt Height (W) - 3.81mm. Breaking strength is not indicative of working strength.

Click for combined categories: All 5mm Pitch Timing Belts

Related Information:
Pulleys stock - 5.000mm GT Pitch.

For simple ready selected sets of timing belts and pulleys please see the HES website


Belts - Timing -  5.000mm Pitch - GT - TRUE METRIC - 9mm Wide

Belts - Timing - 5.000mm Pitch - GT - TRUE METRIC - 9mm Wide

GT Series Metric Timing Belts.

Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.93mm. Belt Height (W) - 3.81mm. Breaking strength is not indicative of working strength.

Click for combined categories: All 5mm Pitch Timing Belts

Related Information:
Pulleys stock - 5.000mm GT Pitch.

For simple ready selected sets of timing belts and pulleys please see the HES website


Leadscrews

Hide Pictures

Go to Top  


Leadscrews - Metric - Acme

Leadscrews - Metric - Acme

Acme Leadscrew Thread - Use with Acme Supernuts


Click for combined categories: All Leadscrews

Click for combined categories: All Metric Leadscrews


Springs Die

Hide Pictures

Go to Top  


Springs - Die - Metric - Heavy Duty

Springs - Die - Metric - Heavy Duty

Colour coded red

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length.

Click for combined categories: All Metric Die Springs

Click for combined categories: All All Die Springs


Springs - Die - Metric - Light Duty

Springs - Die - Metric - Light Duty

Colour coded green

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length.

Click for combined categories: All Metric Die Springs

Click for combined categories: All All Die Springs


Springs - Die - Metric - Medium Duty

Springs - Die - Metric - Medium Duty

Colour coded blue

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length.

Click for combined categories: All Metric Die Springs

Click for combined categories: All All Die Springs


Bearings Tapered Roller

Hide Pictures

Go to Top  


Bearings - Tapered Roller - Single Row - Metric

Bearings - Tapered Roller - Single Row - Metric

Includes cup and cone


Nuts

Hide Pictures

Go to Top  


Nuts - Hexagonal - Steel - Class 10 Metric

Nuts - Hexagonal - Steel - Class 10 Metric

Medium carbon steel. For use with Property Class 10.9 cap screws.


Click for combined categories: All Nuts


Leadscrews

Hide Pictures

Go to Top  


Leadscrew Nuts - Metric - Supernuts - Acme

Leadscrew Nuts - Metric - Supernuts - Acme

Acme Leadscrew Nuts - Use with Acme Leadscrew Thread and flanges for mounting


Click for combined categories: All Leadscrew Nuts

Click for combined categories: All Metric Leadscrew Nuts


Springs Die

Hide Pictures

Go to Top  


Springs - Die - Metric - Extra Heavy Duty

Springs - Die - Metric - Extra Heavy Duty

Colour coded yellow

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length.

Click for combined categories: All Metric Die Springs

Click for combined categories: All All Die Springs


Nuts Lock

Hide Pictures

Go to Top  


Nuts - Lock - For Bearings - Metric KMT High Precision

Nuts - Lock - For Bearings - Metric KMT High Precision

High Strength Steel Lock Nut. Phosphated and saturated with oil Finish.

Locking pin is hard drawn brass. Type MT6SS short pin Grub Screw.

Click for combined categories: All Lock Nuts for Bearings


Pins - Taper

Hide Pictures

Go to Top  


Pins - Taper - Metric - Extractable - Internal Thread

Pins - Taper - Metric - Extractable - Internal Thread

1:50 Taper.

DIN 7978. Mild Steel.

Click for combined categories: All Metric Taper Pins


Mounts Leveling

Hide Pictures

Go to Top  


Mounts - Leveling - Stud Type - Gold Chromate - Metric

Mounts - Leveling - Stud Type - Gold Chromate - Metric

Good quality with value pricing. Hardened ball for high load ratings and excellent wear characteristics.

Large diameter base for added support. 15o off centre swivel for quick leveling on sloped surfaces.

Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - Stud Type - Nickel Plated - Metric

Mounts - Leveling - Stud Type - Nickel Plated - Metric

Good quality with value pricing. Hardened ball for high load ratings and excellent wear characteristics.

Large diameter base for added support. 15o off centre swivel for quick leveling on sloped surfaces.

Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Mounts - Leveling - Stud Type - Stainless Steel - Metric

Mounts - Leveling - Stud Type - Stainless Steel - Metric

Good quality with value pricing. 303 stainless steel.

Large diameter base for added support. 15o off centre swivel for quick leveling on sloped surfaces.

Click for combined categories: All Pivotal Levelers

Click for combined categories: All Mounting Feet


Gears Imperial Worms

Hide Pictures

Go to Top  


Worms - 24 Pitch (Series 1) - Plastic

Worms - 24 Pitch (Series 1) - Plastic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.77o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 32 Pitch (Series 1) - Plastic

Worms - 32 Pitch (Series 1) - Plastic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 32 Pitch (Series 2) - Plastic

Worms - 32 Pitch (Series 2) - Plastic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 8.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 48 Pitch (Series 1) - Plastic

Worms - 48 Pitch (Series 1) - Plastic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 48 Pitch (Series 3) - Plastic

Worms - 48 Pitch (Series 3) - Plastic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 7.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 24 Pitch (Series 1) - Metallic

Worms - 24 Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.77o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 24 Pitch (Series 2) - Metallic

Worms - 24 Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 9.47o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 24 Pitch (Series 3) - Metallic

Worms - 24 Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 18.43o Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 32 Pitch (Series 1) - Metallic

Worms - 32 Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 32 Pitch (Series 2) - Metallic

Worms - 32 Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 8.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 32 Pitch (Series 3) - Metallic

Worms - 32 Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 15.95o Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 48 Pitch (Series 1) - Metallic

Worms - 48 Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 3.35o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 48 Pitch (Series 2) - Metallic

Worms - 48 Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 48 Pitch (Series 3) - Metallic

Worms - 48 Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 7.7o Lead Angle - 2 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 48 Pitch (Series 4) - Metallic

Worms - 48 Pitch (Series 4) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 8.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 48 Pitch (Series 5) - Metallic

Worms - 48 Pitch (Series 5) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 14.2o Lead Angle - 4 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 48 Pitch (Series 6) - Metallic

Worms - 48 Pitch (Series 6) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 14.2o Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 64 Pitch (Series 1) - Metallic

Worms - 64 Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 1.78o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 64 Pitch (Series 2) - Metallic

Worms - 64 Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 3.58o Lead Angle - 2 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 64 Pitch (Series 3) - Metallic

Worms - 64 Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 7.12o Lead Angle - 4 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Gears Metric Stem

Hide Pictures

Go to Top  


Gears - Spur - Module 1 - Stem

Gears - Spur - Module 1 - Stem

Gears with integral shafts.

Metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears

Click for combined categories: All Metric Stem Gears


Gears - Spur - Module 2 - Stem

Gears - Spur - Module 2 - Stem

Gears with integral shafts.

Metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears

Click for combined categories: All Metric Stem Gears


Gears - Spur - Module 0.5 - Stem

Gears - Spur - Module 0.5 - Stem

Gears with integral shafts.

Metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears


Gears - Spur - Module 0.75 - Stem

Gears - Spur - Module 0.75 - Stem

Gears with integral shafts.

Metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears

Click for combined categories: All Metric Stem Gears


Gears - Spur - Module 0.8 - Stem

Gears - Spur - Module 0.8 - Stem

Gears with integral shafts.

Metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears

Click for combined categories: All Metric Stem Gears


Gears - Spur - Module 1.5 - Stem

Gears - Spur - Module 1.5 - Stem

Gears with integral shafts.

Metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Metric Spur Gears

Click for combined categories: All Metric Stem Gears



Select all items starting with...
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9



Store - Categories Pages

Go to Top





Store Pages

Go to Top





Main Pages on Small Parts and Bearings Website




Go to Top

Site Summary:

Freight Rates
Terms and Conditions
Privacy Policy

Small Parts and Bearings offers 151117 products in 3564 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We ship by traceable courier only (no standard post) and we have excellent Freight Rates within Australia and worldwide.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts and Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts and Bearings 1997. All rights reserved.