All Items: Metallic Balls - Categories


Leadscrews

Hide Pictures

Go to Top  


Leadscrew Nuts - Metric - Hexagonal - Metallic

Leadscrew Nuts - Metric - Hexagonal - Metallic

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.

Click for combined categories: All Leadscrew Nuts

Click for combined categories: All Metric Leadscrew Nuts

Related Information:
Metric Whirled Leadscrew


Leadscrew Nuts - Metric - Round - Metallic

Leadscrew Nuts - Metric - Round - Metallic

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.

Click for combined categories: All Leadscrew Nuts

Click for combined categories: All Metric Leadscrew Nuts

Related Information:
Metric Whirled Leadscrew


Leadscrew Nuts - Metric - Square - Metallic

Leadscrew Nuts - Metric - Square - Metallic

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.

Click for combined categories: All Leadscrew Nuts

Click for combined categories: All Metric Leadscrew Nuts

Related Information:
Metric Whirled Leadscrew


Washers Flat Metallic

Hide Pictures

Go to Top  


Washers - C - Steel

Washers - C - Steel

Cold finished steel, case hardened with a black oxide finish.


Click for combined categories: All C Washers


Washers - C - Swing

Washers - C - Swing

Cold finished steel, hardened and ground. Black oxide finish.


Washers - Flat - Aluminium

Washers - Flat - Aluminium

Flat washers.

Click for combined categories: All Flat Washers and Spacers - Metallic


Gears Imperial Worms

Hide Pictures

Go to Top  


Worms - 24 Pitch (Series 1) - Metallic

Worms - 24 Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.77o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 24 Pitch (Series 2) - Metallic

Worms - 24 Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 9.47o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 24 Pitch (Series 3) - Metallic

Worms - 24 Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 18.43o Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 32 Pitch (Series 1) - Metallic

Worms - 32 Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 32 Pitch (Series 2) - Metallic

Worms - 32 Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 8.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 32 Pitch (Series 3) - Metallic

Worms - 32 Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 15.95o Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 48 Pitch (Series 1) - Metallic

Worms - 48 Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 3.35o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 48 Pitch (Series 2) - Metallic

Worms - 48 Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 48 Pitch (Series 3) - Metallic

Worms - 48 Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 7.7o Lead Angle - 2 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 48 Pitch (Series 4) - Metallic

Worms - 48 Pitch (Series 4) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 8.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 48 Pitch (Series 5) - Metallic

Worms - 48 Pitch (Series 5) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 14.2o Lead Angle - 4 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 48 Pitch (Series 6) - Metallic

Worms - 48 Pitch (Series 6) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 14.2o Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 64 Pitch (Series 1) - Metallic

Worms - 64 Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 1.78o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 64 Pitch (Series 2) - Metallic

Worms - 64 Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 3.58o Lead Angle - 2 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - 64 Pitch (Series 3) - Metallic

Worms - 64 Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 7.12o Lead Angle - 4 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Gears Metric Worms

Hide Pictures

Go to Top  


Worms - Module 0.5 (Series 1) - Metallic

Worms - Module 0.5 (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.18o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 0.8 (Series 1) - Metallic

Worms - Module 0.8 (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.82o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 2 (Series 1) - Metallic

Worms - Module 2 (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 3.70o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 3 (Series 1) - Metallic - Left Hand

Worms - Module 3 (Series 1) - Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.92o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 3 (Series 1) - Metallic - Right Hand

Worms - Module 3 (Series 1) - Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.92o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Washers Flat Metallic

Hide Pictures

Go to Top  


Washers - Flat - Bonded Neoprene

Washers - Flat - Bonded Neoprene

Galvanised sealing washers with neoprene centre for use with self drilling screws

Click for combined categories: All Flat Washers and Spacers - Metallic


Washers - Flat - Brass - Commercial

Washers - Flat - Brass - Commercial

Flat washers.

Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.

Click for combined categories: All Flat Washers and Spacers - Metallic


Washers - Flat - Brass - Precision

Washers - Flat - Brass - Precision

Precision Tolerances. Laminated brass shim washers.

Click for combined categories: All Flat Washers and Spacers - Metallic


Washers - Flat - Hardened Steel

Washers - Flat - Hardened Steel

Medium carbon steel through hardened to RC 43-49. Zinc dichromate finish. All dimensions shows are minimum.

Click for combined categories: All Flat Washers and Spacers - Metallic


Washers - Flat - High Tensile

Washers - Flat - High Tensile

Grade 8 high tensile washers

ASTM F436 1985. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Click for combined categories: All Flat Washers and Spacers - Metallic


Washers - Flat - Mild Steel

Washers - Flat - Mild Steel

Flat washers. Includes fender washers. Zinc plated and unplated listings.

In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.

Click for combined categories: All Flat Washers and Spacers - Metallic


Gears Metric Worms

Hide Pictures

Go to Top  


Worm Gears - Module 0.5 (Series 1) - Metallic

Worm Gears - Module 0.5 (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.18o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 0.8 (Series 1) - Metallic

Worm Gears - Module 0.8 (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.82o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 3 (Series 1) - Metallic - Left Hand

Worm Gears - Module 3 (Series 1) - Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.92o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 3 (Series 1) - Metallic - Right Hand

Worm Gears - Module 3 (Series 1) - Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.92o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Washers Flat Metallic

Hide Pictures

Go to Top  


Washers - C - 303 Stainless Steel

Washers - C - 303 Stainless Steel

Knurled outside edge


Click for combined categories: All C Washers


Washers - Flat - Sintered Bronze - Precision

Washers - Flat - Sintered Bronze - Precision

Flat thrust washers made from oil impregnated sintered bronze

Click for combined categories: All Flat Washers and Spacers - Metallic


Washers - Flat - Stainless Steel - Commercial

Washers - Flat - Stainless Steel - Commercial

Flat washers.

Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Click for combined categories: All Flat Washers and Spacers - Metallic


Washers - Heavy Duty - Machined - Steel

Washers - Heavy Duty - Machined - Steel

Case hardened cold finished steel with black oxide finish.

Click for combined categories: All Flat Washers and Spacers - Metallic


Gears Imperial Worms

Hide Pictures

Go to Top  


Worm Gears - 24 Diametrical Pitch (Series 1) - Metallic

Worm Gears - 24 Diametrical Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.77o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 24 Diametrical Pitch (Series 2) - Metallic

Worm Gears - 24 Diametrical Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 9.47o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 24 Diametrical Pitch (Series 3) - Metallic

Worm Gears - 24 Diametrical Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 18.43o Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 32 Diametrical Pitch (Series 1) - Metallic

Worm Gears - 32 Diametrical Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 32 Diametrical Pitch (Series 2) - Metallic

Worm Gears - 32 Diametrical Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 8.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 32 Diametrical Pitch (Series 3) - Metallic

Worm Gears - 32 Diametrical Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 15.95o Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 48 Diametrical Pitch (Series 1) - Metallic

Worm Gears - 48 Diametrical Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 3.35o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 48 Diametrical Pitch (Series 2) - Metallic

Worm Gears - 48 Diametrical Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 48 Diametrical Pitch (Series 3) - Metallic

Worm Gears - 48 Diametrical Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 7.7o Lead Angle - 2 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 48 Diametrical Pitch (Series 4) - Metallic

Worm Gears - 48 Diametrical Pitch (Series 4) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 8.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 48 Diametrical Pitch (Series 5) - Metallic

Worm Gears - 48 Diametrical Pitch (Series 5) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 14.2o Lead Angle - 4 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 48 Diametrical Pitch (Series 6) - Metallic

Worm Gears - 48 Diametrical Pitch (Series 6) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

25o Pressure Angle - 14.2o Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 64 Diametrical Pitch (Series 1) - Metallic

Worm Gears - 64 Diametrical Pitch (Series 1) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 1.78o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 64 Diametrical Pitch (Series 2) - Metallic

Worm Gears - 64 Diametrical Pitch (Series 2) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 3.58o Lead Angle - 2 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - 64 Diametrical Pitch (Series 3) - Metallic

Worm Gears - 64 Diametrical Pitch (Series 3) - Metallic

Worms and Gears must be chosen from the same pitch and series to match.

14.5o Pressure Angle - 7.12o Lead Angle - 4 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Gears Metric Worms

Hide Pictures

Go to Top  


Worms - Module 1.5 (Series 1) - Plastic and Metallic - Left Hand

Worms - Module 1.5 (Series 1) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.43o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 1.5 (Series 1) - Plastic and Metallic - Right Hand

Worms - Module 1.5 (Series 1) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.43o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 1 (Series 1) - Plastic and Metallic - Left Hand

Worms - Module 1 (Series 1) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 1 (Series 1) - Plastic and Metallic - Right Hand

Worms - Module 1 (Series 1) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 2.5 (Series 1) - Plastic and Metallic - Left Hand

Worms - Module 2.5 (Series 1) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.87o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand

Worms - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.87o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 2 (Series 3) - Plastic and Metallic - Left Hand

Worms - Module 2 (Series 3) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.70o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 2 (Series 3) - Plastic and Metallic - Right Hand

Worms - Module 2 (Series 3) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.70o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Timing Belts and Pulleys 9.525mm L (3/8in)

Hide Pictures

Go to Top  


Pulleys - Timing -  9.525mm Pitch - L - 19.1mm Wide - Metallic

Pulleys - Timing - 9.525mm Pitch - L - 19.1mm Wide - Metallic

Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.


Click for combined categories: All L 9.525mm Timing Pulleys

Related Information:
Double Sided Belts to suit 9.525 Pitch L Pulleys - 19mm wide

For simple ready selected sets of timing belts and pulleys please see the HES website


Washers Flat Metallic

Hide Pictures

Go to Top  


Washers - Flat - Stainless Steel - Precision Ground

Washers - Flat - Stainless Steel - Precision Ground

Non magnetic and corrosion resistant. Sides are flat and parallel to within 0.025mm (0.001 in.)

Click for combined categories: All Flat Washers and Spacers - Metallic


Washers - Flat - Stainless Steel - Precision Shim

Washers - Flat - Stainless Steel - Precision Shim

Precision Tolerances.


Click for combined categories: All Precision Shim Washers

Click for combined categories: All Flat Washers and Spacers - Metallic


Washers - Flat - Stamped - Heavy Duty - Hardened

Washers - Flat - Stamped - Heavy Duty - Hardened

Heat treated. Black oxide finish.

Click for combined categories: All Flat Washers and Spacers - Metallic


Washers - Flat - Titanium - CP Grade 1

Washers - Flat - Titanium - CP Grade 1

Flat washers. CP Grade 1 Titanium.

CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Click for combined categories: All Flat Washers and Spacers - Metallic


Washers - Heavy Duty - Machined - Stainless Steel

Washers - Heavy Duty - Machined - Stainless Steel

303 Stainless Steel

Click for combined categories: All Flat Washers and Spacers - Metallic


Gears Metric Worms

Hide Pictures

Go to Top  


Worm Gears - Module 1.5 (Series 1) - Plastic and Metallic - Left Hand

Worm Gears - Module 1.5 (Series 1) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.43o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 1.5 (Series 1) - Plastic and Metallic - Right Hand

Worm Gears - Module 1.5 (Series 1) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.43o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 1.5 (Series 3) - Plastic and Metallic

Worm Gears - Module 1.5 (Series 3) - Plastic and Metallic

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 6.90o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Left Hand

Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Right Hand

Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Left Hand

Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.87o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand

Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.87o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 2 (Series 3) - Plastic and Metallic - Left Hand

Worm Gears - Module 2 (Series 3) - Plastic and Metallic - Left Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.70o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 2 (Series 3) - Plastic and Metallic - Right Hand

Worm Gears - Module 2 (Series 3) - Plastic and Metallic - Right Hand

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.70o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm

Worms - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm

Match with metallic worms Module 0.80 Series 2.

20o Pressure Angle - 4.40o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 1 (Series 2) - Plastic Gear and Metallic Worm

Worms - Module 1 (Series 2) - Plastic Gear and Metallic Worm

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 4.40o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worms - Module 2 (Series 4) - Plastic Gear and Metallic Worm

Worms - Module 2 (Series 4) - Plastic Gear and Metallic Worm

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 4.40o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worms

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Washers Flat Metallic

Hide Pictures

Go to Top  


Washers - Flat - Carbon Spring Steel - Precision Shim

Washers - Flat - Carbon Spring Steel - Precision Shim

Flat Carbon Spring Steel Washers. Commonly used for fast and accurate spacing of milling cutters, gamg cutters, saws, slitting blades and grinding tools.

C1010 steel types best suited to arbor shimming.

Click for combined categories: All Precision Shim Washers

Click for combined categories: All Flat Washers and Spacers - Metallic


Washers - Flat - Titanium - Ti-Gr5/Ti-6AI4v

Washers - Flat - Titanium - Ti-Gr5/Ti-6AI4v

Flat washers. 6AL-4V (Grade 5) High strength titanium alloy.

6AL-4V (Grade 5) High strength titanium alloy, used in critical aircraft structural components. UNS R56400. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Click for combined categories: All Flat Washers and Spacers - Metallic


Gears Metric Worms

Hide Pictures

Go to Top  


Worm Gears - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm

Worm Gears - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm

Match with metallic worms Module 0.80 Series 2.

20o Pressure Angle - 4.40o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 1 (Series 2) - Plastic Gear and Metallic Worm

Worm Gears - Module 1 (Series 2) - Plastic Gear and Metallic Worm

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 4.40o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Worm Gears - Module 2 (Series 4) - Plastic Gear and Metallic Worm

Worm Gears - Module 2 (Series 4) - Plastic Gear and Metallic Worm

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 4.40o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Click for combined categories: All Worm Gears

Related Information:
For simple ready selected sets of worms and gears please see the HES website


Pinion Wire Metric

Hide Pictures

Go to Top  


Gears - Pinion Wire - Module 0.4

Gears - Pinion Wire - Module 0.4

Brass

Metallic. Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use.

Click for combined categories: All Metric Pinion Wire


Gears - Pinion Wire - Module 0.5

Gears - Pinion Wire - Module 0.5

Brass

Metallic. Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use.

Click for combined categories: All Metric Pinion Wire


Gears - Pinion Wire - Module 0.8

Gears - Pinion Wire - Module 0.8

Brass

Metallic. Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use.

Click for combined categories: All Metric Pinion Wire


Pinion Wire Imperial

Hide Pictures

Go to Top  


Gears - Pinion Wire - 24 Diametrical Pitch

Gears - Pinion Wire - 24 Diametrical Pitch

Brass and carbon steel.

Metallic. Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use.

Click for combined categories: All Imperial Pinion Wire


Gears - Pinion Wire - 32 Diametrical Pitch

Gears - Pinion Wire - 32 Diametrical Pitch

Brass and carbon steel.

Metallic. Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use.

Click for combined categories: All Imperial Pinion Wire


Gears - Pinion Wire - 48 Diametrical Pitch

Gears - Pinion Wire - 48 Diametrical Pitch

Brass and carbon steel.

Metallic. Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use.

Click for combined categories: All Imperial Pinion Wire


Gears - Pinion Wire - 64 Diametrical Pitch

Gears - Pinion Wire - 64 Diametrical Pitch

Brass and carbon steel.

Metallic. Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use.

Click for combined categories: All Imperial Pinion Wire


Mounts Leveling

Hide Pictures

Go to Top  


Mounts - Leveling - Import High Value - Rubber Covers

Mounts - Leveling - Import High Value - Rubber Covers

For use with stud or socket type metallic leveling mounts without pads


Bushes Plastic

Hide Pictures

Go to Top  


Bushes - Plastic - Rulon J - Flanged

Bushes - Plastic - Rulon J - Flanged

Non Metallic Bushes. Excellent insulator. 288 oC (550 Deg F) Maximum Working Temperature. Patented all polymeric PTFE compound which operates well against soft mating surfaces. Tolerances - ID and OD +0.051mm / - 0.000mm. Lowest co-efficient of friction in the Rulon(R) product range.

Click for combined categories: All Plastic Bushes

Click for combined categories: All Flanged Plastic Bushes


Bushes - Plastic - Rulon J - Unflanged

Bushes - Plastic - Rulon J - Unflanged

Non Metallic Bushes. Excellent insulator. 288 oC (550 Deg F) Maximum Working Temperature. Patented all polymeric PTFE compound which operates well against soft mating surfaces. Tolerances - ID and OD +0.051mm / - 0.000mm. Lowest co-efficient of friction in the Rulon(R) product range.

Click for combined categories: All Plastic Bushes

Click for combined categories: All Unflanged Plastic Bushes


Gears Imperial Spur

Hide Pictures

Go to Top  


Gears - Spur - 120 Diametrical Pitch - Stem

Gears - Spur - 120 Diametrical Pitch - Stem

303 stainless steel.

Metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Imperial Spur Gears

Click for combined categories: All Imperial Stem Gears


Gears - Spur -  24 Diametrical Pitch - Stem

Gears - Spur - 24 Diametrical Pitch - Stem

303 stainless steel.

Metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Imperial Spur Gears

Click for combined categories: All Imperial Stem Gears


Gears - Spur -  32 Diametrical Pitch - Stem

Gears - Spur - 32 Diametrical Pitch - Stem

303 stainless steel.

Metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Imperial Spur Gears

Click for combined categories: All Imperial Stem Gears


Gears - Spur -  48 Diametrical Pitch - Stem

Gears - Spur - 48 Diametrical Pitch - Stem

303 stainless steel.

Metallic. For easy ready selected sets of rack and gear please see the HES website.

Click for combined categories: All Imperial Spur Gears

Click for combined categories: All Imperial Stem Gears



Select all items starting with...
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9



Store - Categories Pages

Go to Top





Store Pages

Go to Top





Main Pages on Small Parts and Bearings Website




Go to Top

Site Summary

Freight Rates
Terms and Conditions
Privacy Policy

Small Parts and Bearings offers 154810 products in 3693 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer's risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts and Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts and Bearings 1997. All rights reserved.