Quick Delivery Items: Insert And Jaw Type Couplings - Small Parts And Bearings Categories

FOUND IN PARTS DATABASE:- The item was found in our part numbers and descriptions database. Click Here to show the parts found.



Couplings Insert and Jaw Type

Hide Pictures

Go to Top  


Couplings - Three Jaw Type - Inserts

Couplings - Three Jaw Type - Inserts

Match with Three Jaw Type hubs by OD

Use Bost-Bronz inserts for high torque loads at slower speeds. Use rubber for quiter operation. Use polyurethane for moderate to heavy shock loads.

Couplings - Three Jaw Type - Hubs

Couplings - Three Jaw Type - Hubs

Match with Three Jaw Type inserts by OD. Two Hubs and one insert will be needed to make acomplete coupling.

Complete with keyway and set screw. No lubrication needed.

Couplings - HRC

Couplings - HRC


Click for combined categories: All Insert and Jaw Type Couplings

Related Information:
Shafting


Couplings - Spline Type - Complete

Couplings - Spline Type - Complete

0.5 to 4.5 Nm. 12000 to 24000 rpm.

Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 deg C.

Click for combined categories: All Insert and Jaw Type Couplings

Related Information:
Shafting


Couplings - Silicone Insert

Couplings - Silicone Insert

3 to 8 Nm

Zero Backlash. Electrical Isolation. Aluminium Hub with 40 Shore Hardness Silicone Insert.

Click for combined categories: All Insert and Jaw Type Couplings

Related Information:
Shafting


Couplings - Spider Type B - Complete

Couplings - Spider Type B - Complete

Max 3600 RPM. 0.39 to 16.27 Nm. Match only hubs and spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.

Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Rubber spider and metal hubs.

Click for combined categories: All Insert and Jaw Type Couplings

Related Information:
Shafting

Replacement Hubs To Suit


Couplings - Spider Type C - Complete

Couplings - Spider Type C - Complete

Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm. Match only hubs and spiders from listings SPIDER TYPE C. Inserts are held between the jaws of two hubs.

Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in aspacer. Can be used as aflexible coupling in ahigh torque application. Polyurethane spider.

Click for combined categories: All Insert and Jaw Type Couplings

Related Information:
Shafting


Couplings - Spline Type - Spare Hubs

Couplings - Spline Type - Spare Hubs

0.5 to 4.5 Nm. 12000 to 24000 rpm.

Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 deg C.

Click for combined categories: All Insert and Jaw Type Couplings

Related Information:
Shafting


Couplings - Bantam - Complete

Couplings - Bantam - Complete

Isolates vibration up to 85%. Sleeve provides electrical insulation. 0.21Nm at 1725rpm.

Parallel Offset 0.25 mm. Angular Offset 1.5o.

Click for combined categories: All Insert and Jaw Type Couplings

Related Information:
Shafting


Couplings - Multijaw - Precision

Couplings - Multijaw - Precision

Max Torque 3.5 Nm.

303 Stainless Steel. Stainless socket set screws supplied. 48 teeth - 64 Pitch. Max Torque 3.5 N.m (500 oz.in).

Click for combined categories: All Insert and Jaw Type Couplings

Related Information:
Shafting


Couplings - Spider Type A - Hubs Only

Couplings - Spider Type A - Hubs Only

Match only spiders from listings SPIDER TYPE A. Insert is set between the jaws of two hubs.

Split Type Hub. Preloaded Rubber Spider. Minimal backlash. Choice of 3 different spiders for each size provides for different torque requirements. Hubs and spiders available separately or as acomplete unit.

Related Information:
Shafting

Complete Couplings


Couplings - Spider Type B - Hubs Only

Couplings - Spider Type B - Hubs Only

Match 2 hubs with aspider from the spiders category. Match only rubber spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.

Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Metal hubs to suit rubber spiders type B.

Related Information:
Shafting

Complete Couplings


Couplings - Spider Type B - Spiders Only

Couplings - Spider Type B - Spiders Only

Match only hubs from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.

Rubber spders to suit metal hubs type B.

Related Information:
Shafting

Complete Couplings


Couplings - Spline Type - Spare Poyurethane Splines

Couplings - Spline Type - Spare Poyurethane Splines

0.5 to 4.5 Nm. 12000 to 24000 rpm.

Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 deg C.

Click for combined categories: All Insert and Jaw Type Couplings

Related Information:
Shafting


Couplings - Oldham - Complete - Acetal Disk - Clamp Type

Couplings - Oldham - Complete - Acetal Disk - Clamp Type

0.06 to 44 Nm. Max Speed: 3000 RPM.

Max Speed: 3000 RPM. Parallel out of line compensation. Temp Range -20 Deg Cto +60 Deg C. Oldham couplings are designed to transfer torque between two parallel, but not colinear, shafts. They have three discs, one coupled to the input, one coupled to the output, and acentre disc that is joined to the first two by tongue and grooves. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Click for combined categories: All Insert and Jaw Type Couplings

Related Information:
Shafting


Couplings - Oldham - Complete - Acetal Disk - Set Screw

Couplings - Oldham - Complete - Acetal Disk - Set Screw

0.06 to 44 Nm. Max Speed: 3000 RPM.

Max Speed: 3000 RPM. Parallel out of line compensation. Temp Range -20 Deg Cto +60 Deg C. Oldham couplings are designed to transfer torque between two parallel, but not colinear, shafts. They have three discs, one coupled to the input, one coupled to the output, and acentre disc that is joined to the first two by tongue and grooves. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Click for combined categories: All Insert and Jaw Type Couplings

Related Information:
Shafting


Couplings Other

Hide Pictures

Go to Top  


Couplings - Sleeve Type - Complete

Couplings - Sleeve Type - Complete

0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:
Shafting

Replacement Hubs to Suit Sleeve Type Couplings


Couplings - Sleeve Type - Hubs

Couplings - Sleeve Type - Hubs

0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:
Shafting


Couplings - Sleeve Type - Sleeves

Couplings - Sleeve Type - Sleeves

0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:
Shafting


Couplings Helical and Slit

Hide Pictures

Go to Top  


Couplings - Slit Type - 4 Slit Miniature - Set Screw Type - Aluminium

Couplings - Slit Type - 4 Slit Miniature - Set Screw Type - Aluminium

Aluminium - Flexible.


Click for combined categories: All Helical and Slit Couplings


Couplings - Slit Type - Plastic - Clamp Hub

Couplings - Slit Type - Plastic - Clamp Hub

Lightweight molded patented coupling can replace many stainless or aluminum slit type couplings with lost coast and improved operation.

No windup or backlash or any derating for reversing applications. To ensure tight fit between shaft and coupling, ametal screw to metal nut design is used and does not utilize threads cut into moulded piece. Operating temperature -20o to 140o Celius. Made of Engineered polymer with stainless fastners. UV reisitant. Voltage and RF isolation.

Click for combined categories: All Helical and Slit Couplings


Couplings - Slit Type - Plastic - Set Screw

Couplings - Slit Type - Plastic - Set Screw

Lightweight molded patented coupling can replace many stainless or aluminum slit type couplings with lost coast and improved operation.

No windup or backlash or any derating for reversing applications. To ensure tight fit between shaft and coupling, ametal screw to metal nut design is used and does not utilize threads cut into moulded piece. Operating temperature -20o to 140o Celius. Made of Engineered polymer with stainless fastners. UV reisitant. Voltage and RF isolation.

Click for combined categories: All Helical and Slit Couplings


Couplings - Slit Type - Standard

Couplings - Slit Type - Standard

Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.

High Torsional Stiffness. Zero Backlash.

Click for combined categories: All Helical and Slit Couplings

Related Information:
Shafting


Couplings - Reli-a-flex - Long Series - Clamp Type

Couplings - Reli-a-flex - Long Series - Clamp Type

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 Deg Cto plus 80 Deg C.

Click for combined categories: All Helical and Slit Couplings

Related Information:
Shafting


Couplings - Reli-a-flex - Short Series - Clamp Type

Couplings - Reli-a-flex - Short Series - Clamp Type

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 Deg Cto plus 80 Deg C.

Click for combined categories: All Helical and Slit Couplings

Related Information:
Shafting


Couplings - Reli-a-flex - Short Series - Set Screw Type

Couplings - Reli-a-flex - Short Series - Set Screw Type

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 Deg Cto plus 80 Deg C.

Click for combined categories: All Helical and Slit Couplings

Related Information:
Shafting


Couplings - Spiral Beam - 6 Beam - Aluminium - Set Screw Type

Couplings - Spiral Beam - 6 Beam - Aluminium - Set Screw Type

Pilot Bore size not toleranced. Finished Bore sizes to +0.03/0.00.

Click for combined categories: All Helical and Slit Couplings

Related Information:
Shafting


Suspension Units

Hide Pictures

Go to Top  


Suspension Units - Rubber - Square - Insert Type

Suspension Units - Rubber - Square - Insert Type

Housing: Steel / Rubber: Black, hardness 70 Shore. Inner square section: Steel tube for mounting plug-in lever arms on one or both sides. All metal parts are paint-finished. Maximum Working Angle: +/-30o. Operating Temperature Range: -40oCto +80oC.

Click for combined categories: All Suspension Units


Tools Bits

Hide Pictures

Go to Top  


Bits - Insert

Bits - Insert

Insert bits for use with hand type screwdriver bit holders


Hooks

Hide Pictures

Go to Top  


Turnbuckles - Jaw and Jaw - 316 Stainless Steel

Turnbuckles - Jaw and Jaw - 316 Stainless Steel

Meets dimensions of ASTM specification F1145-92 Type 1, Class D


Click for combined categories: All Turn Buckles


Bearings and Housings Insert Type

Hide Pictures

Go to Top  


Housings - Bearing - Flanged - Square - Plastic

Housings - Bearing - Flanged - Square - Plastic

Use with steel, plastic or stainless steel bearing inserts for plastic housings.

Load and speed capability depend on the bearing used.

Related Information:
Other Bearings to Suit


Housings - Bearing - Pillow Block - Plastic

Housings - Bearing - Pillow Block - Plastic

Use with steel or plastic bearing inserts for plastic housings.

Load and speed capability depend on the bearing used.

Related Information:
Bearings for Plastic Housings


Hooks

Hide Pictures

Go to Top  


Turnbuckles - Jaw and Jaw - Forged Carbon Steel

Turnbuckles - Jaw and Jaw - Forged Carbon Steel

Hot galvanised, meets USA Federal specifications FF-T-791b, Type I, Form 1-class 4

Coarse threads.

Click for combined categories: All Turn Buckles


Bearings and Housings Insert Type

Hide Pictures

Go to Top  


Housings - Bearing - Flanged - Offset - Cast Iron

Housings - Bearing - Flanged - Offset - Cast Iron

Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.

Related Information:
Plastic Bearings to Suit


Housings - Bearing - Flanged - Round - Cast Iron

Housings - Bearing - Flanged - Round - Cast Iron

Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.

Related Information:
Plastic Bearings to Suit


Housings - Bearing - Flanged - Square - Cast Iron

Housings - Bearing - Flanged - Square - Cast Iron

Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.

Related Information:
Plastic Bearings to Suit


Housings - Bearing - Pillow Block - Cast Iron

Housings - Bearing - Pillow Block - Cast Iron

Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.

Related Information:
Plastic Bearings to Suit


Housings - Bearing - Pillow Block - Pressed Metal

Housings - Bearing - Pillow Block - Pressed Metal

Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.

Housings - Bearing - Flanged - 2 Bolt Hole - Plastic

Housings - Bearing - Flanged - 2 Bolt Hole - Plastic

Load and speed capability depend on the bearing used. Use with steel or plastic bearing inserts for plastic housings.

Related Information:
Other Bearings to Suit


Thread Inserts

Hide Pictures

Go to Top  


Inserts - Thread Repair - Helicoil Installation Tools

Inserts - Thread Repair - Helicoil Installation Tools

Tools for helicoil inserts include economy style and production style prewinder and threaded mandrel types


Bearings and Housings Insert Type

Hide Pictures

Go to Top  


Housings - Bearing - Flanged - 2 Bolt Hole - Cast Iron

Housings - Bearing - Flanged - 2 Bolt Hole - Cast Iron

Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.

Related Information:
Plastic Bearings to Suit


Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal

Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal

Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.

Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal

Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal

Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.

Couplings Other

Hide Pictures

Go to Top  


Couplings - Vibration Absorption

Couplings - Vibration Absorption

For servo and stepper motors. Backlash free. Cap screw fixing.

Aluminium A2017 Hub. HNBR Anti-Vibration Rubber Insert. Black Oxide Coated Cap Screw SCM435 Steel. Minus 20 Deg Cto 80 Deg COperating Temperature. High torque. High response. Zero backlash. Electrical insulation.

Couplings Helical and Slit

Hide Pictures

Go to Top  


Couplings - Flex Beam - Clamp Style

Couplings - Flex Beam - Clamp Style

Zero backlash machined from asingle piece of aluminium and featuring two sets of spiral cuts.

Higher torque and reduced windup compared to commodity type single beam couplings.

Click for combined categories: All Helical and Slit Couplings


Couplings - Flex Beam - Set Screw Style

Couplings - Flex Beam - Set Screw Style

Zero backlash machined from asingle piece of aluminium and featuring two sets of spiral cuts.

Higher torque and reduced windup compared to commodity type single beam couplings.

Click for combined categories: All Helical and Slit Couplings


Couplings Rigid

Hide Pictures

Go to Top  


Couplings - Rigid - 1 Piece Clamp - Stainless Steel

Couplings - Rigid - 1 Piece Clamp - Stainless Steel

303 Grade Stainless

Precision Machined. High torsional load. Non marring, easy to install and adjust. Use on hardened shafts, rigid clamp type design, easily machinable. Available with stepped bores and keyways on 5 week delivery.

Click for combined categories: All Rigid Couplings


Knobs Ball

Hide Pictures

Go to Top  


Knobs - Ball - Knock On - Phenolic

Knobs - Ball - Knock On - Phenolic

Moulded from black phenolic resin.

Light Weight. Thermal insulating. Non corrosive. POK Type have aribbed insert. Shaft should be 0 to 0.007 mm undersized for best results. 712 Type suit standard metric rod.

Click for combined categories: All Ball Knobs


Clamps

Hide Pictures

Go to Top  


Clamps - Syncro - Mounting - Sintered

Clamps - Syncro - Mounting - Sintered

Sintered Stainless Steel 316. Screw Treat Per MIL-S-5002, Clamp as cast and tumbled. Insert - Nylon Type 1 per MIL-M20693, Natural Colour.

Click for combined categories: All Syncro Clamps


Hooks

Hide Pictures

Go to Top  


Hooks - Chain - Kuplex II Kuplok

Hooks - Chain - Kuplex II Kuplok

Approved for lifting. Mechanical coupling links.

An essential componenet of mechanically coupled slings. Used to assemble chain legs to the master link and / or attach eye type fittings.

Click for combined categories: All Lifting Hooks


Dental Handpiece Parts

Hide Pictures

Go to Top  


Coupling NSK Parts

Coupling NSK Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

Couplings Other

Hide Pictures

Go to Top  


Couplings - KType

Couplings - KType

Up to 3600 RPM - Minus 20 to Plus 60o C. 0.34 to 18 Nm.

Strong, flexible polyurethane or Hyrtel(R) is cut and tear resistant. Up to 3600 RPM. Urethane: Minus 20 to Plus 60o C / Hyrtel(R) : Minus 40 to Plus 100o C. Precision swaged mechanically crimped hubs. Annealed steel hubs.

Related Information:
Shafting


Dental Handpiece Parts

Hide Pictures

Go to Top  


Coupling - Multiflex Kavo Parts

Coupling - Multiflex Kavo Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

Coupling - Low Speed Kavo Parts

Coupling - Low Speed Kavo Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

Multiflex Coupling Kavo Parts

Multiflex Coupling Kavo Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

Couplings Rigid

Hide Pictures

Go to Top  


Couplings - Rigid - 2 Piece Clamp - Steel

Couplings - Rigid - 2 Piece Clamp - Steel

12L14 Steel

Precision Machined. High torsional load. Non marring, easy to install and adjust. Assemble without moving shafts. Use on hardened shafts, rigid clamp type design, easily machinable. Black finish with alloy steel cap screws. Available with stepped bores and keyways on 5 week delivery.

Click for combined categories: All Rigid Couplings


Thread Inserts

Hide Pictures

Go to Top  


Inserts - Thread Repair - Recoil

Inserts - Thread Repair - Recoil

Recoil inserts are screwed directly into an enlarged tapped hole. Replacement inserts for your kit.

Stainless inserts. Replacement Individual Inserts - Require full kit to obtain correct tap. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has atensile strength of greater than 200,000 P.S.I. and afinish better than 32 micro inches.

Click for combined categories: All Recoil Inserts and Kits


Pins - Ball Lock

Hide Pictures

Go to Top  


Pins - Ball Lock - Shoulder Type - THandle

Pins - Ball Lock - Shoulder Type - THandle

Zinc plated C1144 pins with ashoulder that prevents the pin being inserted all the way to the handle.


Click for combined categories: All Ball Lock Pins


Gearmotors Basic

Hide Pictures

Go to Top  


Gearmotors - Basic - Hobby - 12.1mm Diameter

Gearmotors - Basic - Hobby - 12.1mm Diameter

Small light weight geared motors used in toys and small solar applications

NOTE! These do not have astandard output shaft. The output is aplastic crossed block (see diagram) which is designed to be fitted to afabricated coupling in O.E.Mapplications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.

Click for combined categories: All Basic Gearmotors


Couplings Other

Hide Pictures

Go to Top  


Couplings - Slip - Spring Wrapped

Couplings - Slip - Spring Wrapped

Tension control - transmission overload protection. 0.035 to 1.69 Nm.

Coupling is sliped over one shaft and screws tightened. Second shaft is inserted into other end. Loose end of coupling is pulled back about 0.5mm then screws tightened. Serves as atorque limiter as well as acoupling. Long life under continuous slip applications.

Related Information:
Shafting


Pins - Ball Lock

Hide Pictures

Go to Top  


Pins - Ball Lock - Flanged Receptacles

Pins - Ball Lock - Flanged Receptacles

Provide apermanent and proper mating hole for commercial and industrial type quick release ball lock pins.

Designed to be used on materials or in applications where the pin does not have anything to lock against. Pin does not protrude past the bottom of the receptacle so they are ideal for blind hole applications. 303 Stainless Steel. Mounted with screws, rivets or bolts. The quick release ball lock pins are inserted from the flanged end, and the ball extends into the wider opening at the top of the receptacle.

Thread Inserts

Hide Pictures

Go to Top  


Inserts - Expansion - Press In - 303 Stainless - Flanged

Inserts - Expansion - Press In - 303 Stainless - Flanged

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings.


Click for combined categories: All Expansion Inserts


Inserts - Expansion - Press In - 303 Stainless Steel

Inserts - Expansion - Press In - 303 Stainless Steel

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings.

Material : 303 Stainless Steel. Easiest inserts to install - simply push into apre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.

Click for combined categories: All Expansion Inserts


Inserts - Expansion - Press In - Brass

Inserts - Expansion - Press In - Brass

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings.

Material : Brass. Easiest inserts to install - simply push into apre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.

Click for combined categories: All Expansion Inserts


Inserts - Expansion - Press In - Brass - Flanged

Inserts - Expansion - Press In - Brass - Flanged

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings.


Click for combined categories: All Expansion Inserts


Inserts - Rivet Nuts - Klik - Ribbed

Inserts - Rivet Nuts - Klik - Ribbed

Individual Inserts for use with the Klik Thread Setter Tool

These blind thread inserts offer strong torque and pull out characteristics. Especially effective in sheet metal and other thin material. Insert is placed into the hole in the parent material and crimped up with the installation tool. Installs from one side - no tapping required. Installs almost flush eliminating the need for countersinking. Made from plated steel.

Click for combined categories: All Klik Rivet Nuts

Related Information:
Mandrels and Nosepieces


Inserts - Rivet Nuts - Klik - Standard

Inserts - Rivet Nuts - Klik - Standard

Individual Inserts for use with the Klik Thread Setter Tool

These inserts can be used in blind or through hole applications. Featuring aheavy duty thread profile and increased thickness in the collapse area. Steel with cadmium plating.

Click for combined categories: All Klik Rivet Nuts

Related Information:
Mandrels and Nosepieces


Inserts - Rivet Nuts - Klik - Threadsert

Inserts - Rivet Nuts - Klik - Threadsert

Individual Inserts for use with the Klik Thread Setter Tool

These inserts can be used in blind or through hole applications. Can be used in almost any material over 0.8mm thick. As the insert is installed the threaded section is completely swaged into the sleeve portion of the hole, permitting them to be used with grade 8 screws. The installation hole size is determined by the density of the parent material.

Click for combined categories: All Klik Rivet Nuts

Related Information:
Mandrels and Nosepieces


Inserts - Self Tapping - For Aluminium - Stainless 303

Inserts - Self Tapping - For Aluminium - Stainless 303

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides astrong wear and vibration resistant thread. Low volumes can be installed by winding in with abolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.

Click for combined categories: All Self Tapping Inserts


Inserts - Self Tapping - For Aluminium - Steel

Inserts - Self Tapping - For Aluminium - Steel

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides astrong wear and vibration resistant thread. Low volumes can be installed by winding in with abolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.

Click for combined categories: All Self Tapping Inserts


Inserts - Self Tapping - For Plastics - Stainless 303

Inserts - Self Tapping - For Plastics - Stainless 303

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides astrong wear and vibration resistant thread. Low volumes can be installed by winding in with abolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from 303 stainless steel.

Click for combined categories: All Self Tapping Inserts


Inserts - Self Tapping - For Plastics - Steel

Inserts - Self Tapping - For Plastics - Steel

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides astrong wear and vibration resistant thread. Low volumes can be installed by winding in with abolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.

Click for combined categories: All Self Tapping Inserts


Inserts - Self Tapping - For Wood - Hex Drive

Inserts - Self Tapping - For Wood - Hex Drive

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Die Cast Zinc Alloy. Knife thread cuts easily into apredrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with ahex wrench.

Click for combined categories: All Self Tapping Inserts for Wood

Click for combined categories: All Self Tapping Inserts


Inserts - Self Tapping - For Wood - Hex Drive - Flanged

Inserts - Self Tapping - For Wood - Hex Drive - Flanged

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Die Cast Zinc Alloy. Knife thread cuts easily into apredrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with ahex wrench.

Click for combined categories: All Self Tapping Inserts for Wood

Click for combined categories: All Self Tapping Inserts


Inserts - Self Tapping - For Wood - Slotted Drive

Inserts - Self Tapping - For Wood - Slotted Drive

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides astrong wear and vibration resistant thread. Low volumes can be installed by winding in with abolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.

Click for combined categories: All Self Tapping Inserts for Wood

Click for combined categories: All Self Tapping Inserts


Inserts - Self Tapping - For Wood - Slotted Drive - Short

Inserts - Self Tapping - For Wood - Slotted Drive - Short

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Brass. Install with ascrewdriver. Superior holding power in hard and soft woods, particle board and other wood products. Long pilot assists with straight driving into adrilled hole.

Click for combined categories: All Self Tapping Inserts for Wood

Click for combined categories: All Self Tapping Inserts


Inserts - Tapered Fit - Finserts - For Wood and Plastics

Inserts - Tapered Fit - Finserts - For Wood and Plastics

Finserts provide strong metal threads in wood, composition board and thermoplastics such as nylon, polystyrene, cellulose acetate and cycolac. By distributing stress over agreater surface area, firm permanent fastening is ensured.

The fins give higher holding strength in softer materials. Available with one, two or three fins for varying material thickness. Finserts prevent splintering, splitting and thread pullout.

Inserts - Thread Repair - EZ-Lok - Individual Kits

Inserts - Thread Repair - EZ-Lok - Individual Kits

Contains 20 inserts per kit along with astandard tap, drill bit and installation tool. Installation tool is not needed but will make multiple installations easier.

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with abolt and wrench. Metric, UNC and UNF.

Click for combined categories: All EZ Lok inserts and Kits


Inserts - Thread Repair - EZ-Lok - Solid 303 Stainless Steel

Inserts - Thread Repair - EZ-Lok - Solid 303 Stainless Steel

Easy to install with astandard tap, bolt and wrench.

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with abolt and wrench. Metric, UNC and UNF.

Click for combined categories: All EZ Lok inserts and Kits


Inserts - Thread Repair - EZ-Lok - Solid Carbon Steel

Inserts - Thread Repair - EZ-Lok - Solid Carbon Steel

Easy to install with astandard tap, bolt and wrench.

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with abolt and wrench. Metric, UNC and UNF.

Click for combined categories: All EZ Lok inserts and Kits


Inserts - Thread Repair - Helicoil

Inserts - Thread Repair - Helicoil

Replacement helicoil inserts for after you have purchased astarter kit or tools separately.

Stainless 18-8 inserts with ahardness of RC43-50 and tensile strength above 200,000 PSI. Metric and Imperial available. Screw locking inserts have aseries of straight segments to provide self-locking torque on the bolt, eliminating aneed for other threadlocking methods.

Click for combined categories: All Helicoil Inserts and Kits


Inserts - Thread Repair - Helicoil Extracting Tools

Inserts - Thread Repair - Helicoil Extracting Tools

Extracting tools are used to remove helicoil inserts. This is done by applying the tool to the insert, striking the tools head and turning it counter-clockwide.


Inserts - Thread Repair - Helicoil Starter Sets

Inserts - Thread Repair - Helicoil Starter Sets

Helicoil sets include 3 lengths of 1x, 1.5x and 2x the thread diameter. Also included is atap, an installation tool, adrill and atang removal tool packed in asturdy plastic case.

Stainless inserts. Full instructions included. Helicoil kits include aprewinder tool for fine threads or athreaded mandrel for course and metric threads. Metric and Imperial available.

Click for combined categories: All Helicoil Inserts and Kits


Inserts - Thread Repair - Helicoil Tang Breakoff Tools

Inserts - Thread Repair - Helicoil Tang Breakoff Tools

The driving tangs of helicoil inserts must be removed to prevent interference with the end of the assembled screw. For inserts over 1/2 inch use long nosed pliers.


Inserts - Thread Repair - Keylocking

Inserts - Thread Repair - Keylocking

Steel or 303 Stainless Steel as indicated in the tables. Also known as keenserts.

Steel or 303 Stainless Steel as indicated in the tables. Maximum strength and reliability. Positive mechanical lock against rotation:. The insert kees are driven down into the tapped threads of the parent material during installation to securely lock the insert against rotation. Inserts with internal thread lock are designed to securely lock abolt when it is entered into the insert only afew turns.

Click for combined categories: All Keylocking Inserts and Kits


Inserts - Thread Repair - Keylocking Assortment Kits

Inserts - Thread Repair - Keylocking Assortment Kits

Also known as keenserts.


Click for combined categories: All Keylocking Inserts and Kits


Inserts - Thread Repair - Keylocking Insertion Tools

Inserts - Thread Repair - Keylocking Insertion Tools

Used to insert keylocking inserts - keensert style. Keylocking inserts can be wound in without these tools but the tools make the job much easier. Also known as keenserts.


Inserts - Thread Repair - Keylocking Starter Sets

Inserts - Thread Repair - Keylocking Starter Sets

Keylocking inserts are used to repair threads by tapping the worn thread to astandard larger thread, twisting the insert into place and then driving in the keys to lock the insert. Also known as keenserts.

Each kit contains an installation tool and the quantity of inserts shown. One size per kit. Also known as keenserts, keylocking inserts are available in mild steel and stainless steel.

Click for combined categories: All Keylocking Inserts and Kits


Assortments

Hide Pictures

Go to Top  


Inserts - Thread Repair - EZ-Lok - Selection Kits

Inserts - Thread Repair - EZ-Lok - Selection Kits

Contains aselection of E-ZLok inserts

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with abolt and wrench. Metric, UNC and UNF.

Click for combined categories: All EZ Lok inserts and Kits


Couplings Bellows

Hide Pictures

Go to Top  


Couplings - Bellows - External Clamp and Set Screw - Brass

Couplings - Bellows - External Clamp and Set Screw - Brass

Zero Backlash - Tin Plate - Angular Misalignment up to 5o

Phosphor Bronze Bellows. Brass set screw hub one end, berrylium copper clamp hub other end. Match with precision or commercial gear clamps - see link.

Click for combined categories: All Bellows Couplings

Related Information:
Shafting


Couplings - Bellows - External Clamp - Brass

Couplings - Bellows - External Clamp - Brass

Zero Backlash - Tin Plate - Angular Misalignment up to 10o (Refer Tables)

Phosphor Bronze Bellows. Beryllium Copper Hubs. Match with precision or commercial gear clamps - see link.

Click for combined categories: All Bellows Couplings

Related Information:
Shafting


Couplings - Bellows - Hiflex - Clamp Hub

Couplings - Bellows - Hiflex - Clamp Hub

Precise adjustment - Vibration resistance - Large misalignment capability. 0.01 to 9.17 Nm. 2000 rpm. - Zero Backlash

Wide torque range. Zero cyclic speed variation during 360 Deg. Rotation. Very low torsional deflection.

Click for combined categories: All Bellows Couplings

Related Information:
Shafting


Couplings - Bellows - Hiflex - Integral Clamp Hub

Couplings - Bellows - Hiflex - Integral Clamp Hub

Precise adjustment - Vibration resistance - Large misalignment capability. 0.01 to 9.17 Nm. 2000 rpm. - Zero Backlash

Wide torque range. Zero cyclic speed variation during 360 Deg. Rotation. Very low torsional deflection.

Click for combined categories: All Bellows Couplings

Related Information:
Shafting


Couplings - Bellows - Hiflex - Pin Hub

Couplings - Bellows - Hiflex - Pin Hub

Precise adjustment - Vibration resistance - Large misalignment capability. 0.01 to 9.17 Nm. 2000 rpm. - Zero Backlash

Wide torque range. Zero cyclic speed variation during 360 Deg. Rotation. Very low torsional deflection.

Click for combined categories: All Bellows Couplings

Related Information:
Shafting


Couplings - Bellows - Integral Clamp - 316 Stainless

Couplings - Bellows - Integral Clamp - 316 Stainless

Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics

Stainless Steel 303L Bellows. Stainless Steel 316 Hubs.

Click for combined categories: All Bellows Couplings

Related Information:
Shafting


Couplings - Bellows - Integral Clamp - Aluminium

Couplings - Bellows - Integral Clamp - Aluminium

Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics

Phosphor Bronze Bellows. Aluminium Hubs.

Click for combined categories: All Bellows Couplings

Related Information:
Shafting



Select all items starting with...
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9



Store - Categories Pages

Go to Top





Store Pages

Go to Top





Main Pages on Small Parts and Bearings Website




Go to Top

Site Summary

Freight Rates
Terms and Conditions
Privacy Policy

Small Parts and Bearings offers 155215 products in 3613 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We ship by traceable courier only (no standard post) and we have excellent Freight Rates within Australia and worldwide.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts and Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts and Bearings 1997. All rights reserved.