FOUND IN PART NUMBERS:- The item was found in our part numbers database. The results of this search are shown below. If you would prefer to run the search again without checking the part numbers database please Click Here
Possible part number matches for HUBS
CP-032-HUB-SLV--15 found in Couplings - Sleeve Type - Hubs
Bore: 3.175 / 3.175. Coupling OD: 14.7. Length: 10.30.
CP-040-HUB-SLV--15 found in Couplings - Sleeve Type - Hubs
Bore: 4.000 / 4.000. Coupling OD: 14.7. Length: 10.30.
CP-048-HUB-SLV--15 found in Couplings - Sleeve Type - Hubs
Bore: 4.762 / 4.762. Coupling OD: 14.7. Length: 10.30.
CP-050-HUB-SLV--15 found in Couplings - Sleeve Type - Hubs
Bore: 5.000 / 5.000. Coupling OD: 14.7. Length: 10.30.
CP-060-HUB-SLV--15 found in Couplings - Sleeve Type - Hubs
Bore: 6.000 / 6.000. Coupling OD: 14.7. Length: 10.30.
CP-060-HUB-SLV--21 found in Couplings - Sleeve Type - Hubs
Bore: 6.000 / 6.000. Coupling OD: 21.0. Length: 15.47.
CP-064-HUB-SLV--15 found in Couplings - Sleeve Type - Hubs
Bore: 6.350 / 6.350. Coupling OD: 14.7. Length: 10.30.
CP-064-HUB-SLV--21 found in Couplings - Sleeve Type - Hubs
Bore: 6.350 / 6.350. Coupling OD: 21.0. Length: 15.47.
CP-079-HUB-SLV--21 found in Couplings - Sleeve Type - Hubs
Bore: 7.938 / 7.938. Coupling OD: 21.0. Length: 15.47.
CP-079-HUB-SLV--27 found in Couplings - Sleeve Type - Hubs
Bore: 7.938 / 7.938. Coupling OD: 27.4. Length: 19.05.
Categories for: hubs
Couplings - Oldham - Hubs - Clamp Style
0.06 to 44 Nm. Max Speed: 3000 RPM.
Disk inserts. Single hubs. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.
Couplings - Oldham - Hubs - Set Screw Style
0.06 to 44 Nm. Max Speed: 3000 RPM.
Disk inserts. Single hubs. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.
Couplings - Spline Type - Hubs
0.5 to 4.5 Nm. 12000 to 24000 rpm.
Angular Misalignment: 2 Deg. Parallel Offset: 0.2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 deg C.
Couplings - Three Jaw Type - Hubs
Match with Three Jaw Type inserts by OD. Two Hubs and one insert will be needed to make a complete coupling.
Complete with keyway and set screw. No lubrication needed.
Couplings - Crowned Tooth Gear - Hubs Only
Match with sleeves from the sleeves category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1 Degree Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Couplings - Sleeve Type - Hubs
0.05 to 2.1 Nm. Max Speed 1750 rpm.
Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.
Couplings - Rubber Spider Jaw Type - Hub Only
Match 2 hubs with a spider from the spiders category
Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM.
Sprockets - 3.75mm Pitch x 1.6mm Tooth Width - Simplex - Stainless Steel
With and without Hubs. Miniature 3.75mm Pitch.
Match with 0375 Series Simplex Chain.
Sprockets - 6.35mm Pitch x 2.8mm Tooth Width - Simplex - Metal
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain. American Standard 25-1 - 1/4 inch.
Sprockets - 6.35mm Pitch x 2.8mm Tooth Width - Simplex - Stainless Steel
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain. American Standard 25-1 - 1/4 inch.
Couplings - Three Jaw Type - Inserts
Match with Three Jaw Type hubs by OD
Use Bost-Bronz inserts for high torque loads at slower speeds. Use rubber for quiter operation. Use polyurethane for moderate to heavy shock loads.
Couplings - BoWex - Tooth Driven - Sintered Steel
Sintered steel hubs and nylon centre sleeve
Operating temp range -25 Deg C to 100 Deg C. Maintenance free. Compensates for axial, radial and angular shaft displacement. Easy to assemble. Alternative bore and keyway sizes can be supplied on approx 5 weeks delivery. Please contact our sales staff to arrange this.
Couplings - BoWex - Tooth Driven - Stainless Steel
Corrosion resistant stainless steel hubs and polyamide centre sleeve
Hubs 320 518/31 (316 Ti) 1.4571 Stainless Steel.
Couplings - Crowned Tooth Gear - Complete
Steel hubs with Moulded Nylon Sleeve.
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1 Degree Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Couplings - Crowned Tooth Gear - Sleeve Only
Match with hubs from the hubs category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1 Degree Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Couplings - Miniflex - Stainless Steel Flat Wire Type
Light metal hubs and stainless steel wire. Up to 120 Deg C.
Rollers - Urethane Feed - With Hub
Urethane coated aluminium alloy feed rollers with hub.
Roller - Urethane 60 Durometer, Ground Outside Diameter. Sleeve - Aluminium.
For fast and accurate positioning and locking of components on shafts.
Fast and frequent mounting and dismounting with only one screw. No axial movement when mounted. Uniform surface pressure against shaft component prevents damage to these parts. Temperature range Minus 30 Deg C to Plus 82 Deg C. Double walled sleeve expands when the pressure screw is tightened to the specified torque. Dismantled easily by releasing pressure on the screw.
Friction grip construction.
Connects rotating components to shafts. Transmits high torque without keyways. Two styles - see diagrams.
Gears - Spur - 120 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
Gears - Spur - 24 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
Gears - Spur - 32 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
Gears - Spur - 48 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
Gears - Spur - 64 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
Gears - Spur - 72 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
Gears - Spur - 80 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
Gears - Spur - 96 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
Couplings - Bellows - Conical Hub - Stainless Steel 18 to 5000Nm
Stainless steel bellows with Steel hub
Couplings - Bellows - Hiflex - Clamp Hub
Precise adjustment - Vibration resistance - Large misalignment capability. 0.01 to 9.17 Nm. 2000 rpm. - Zero Backlash
Wide torque range. Zero cyclic speed variation during 360 Deg. Rotation. Very low torsional deflection.
Couplings - Bellows - Hiflex - Integral Clamp Hub
Precise adjustment - Vibration resistance - Large misalignment capability. 0.01 to 9.17 Nm. 2000 rpm. - Zero Backlash
Wide torque range. Zero cyclic speed variation during 360 Deg. Rotation. Very low torsional deflection.
Couplings - Bellows - Hiflex - Pin Hub
Precise adjustment - Vibration resistance - Large misalignment capability. 0.01 to 9.17 Nm. 2000 rpm. - Zero Backlash
Wide torque range. Zero cyclic speed variation during 360 Deg. Rotation. Very low torsional deflection.
Couplings - Bellows - Outer Conical Hub - Stainless Steel 18 to 5000Nm
Stainless steel bellows with Steel hub
Couplings - Slit Type - Plastic - Clamp Hub
Lightweight molded patented coupling can replace many stainless or aluminum slit type couplings with lost coast and improved operation.
No windup or backlash or any derating for reversing applications. To ensure tight fit between shaft and coupling, a metal screw to metal nut design is used and does not utilize threads cut into moulded piece. Operating temperature -20 Degrees to 140 Degrees Celius. Made of Engineered polymer with stainless fastners. UV reisitant. Voltage and RF isolation.
Collars - Shaft - Hinged Type - Round - Stainless Steel
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Collars - Shaft - Hinged Type - Round - Steel
Precision machined. Convenient easy-to-assemble design. Steel 12L14 (9SMn Pb36)
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Use with disc dial indexes.
Precision Engraved. Use with HUBS - Gear and Dial. 2024 Aluminium Black Anodized. Engraving filled with white enamel.
Use with drum dial indexes.
Precision Engraved. Use with HUBS - Gear and Dial. 2024 Aluminium Black Anodized. Engraving filled with white enamel.
Sprockets - 12.7mm Pitch x 7.75mm Tooth Width - Simplex - Metal
Match with 12700775 Series Simplex Chain (08B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.
Sprockets - 9.53mm Pitch x 5.7mm Tooth Width - Duplex - Metal
Match with series 0953057 Duplex steel chain (06B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch Duplex. With and without hubs.
Couplings - Bellows - External Clamp - Brass
Zero Backlash - Tin Plate - Angular Misalignment up to 10 Degree (Refer Tables)
Phosphor Bronze Bellows. Beryllium Copper Hubs. Match with precision or commercial gear clamps - see link.
Couplings - Bellows - Integral Clamp - 316 Stainless
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Stainless Steel 303L Bellows. Stainless Steel 316 Hubs.
Couplings - Bellows - Integral Clamp - Aluminium
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Phosphor Bronze Bellows. Aluminium Hubs.
Couplings - Bellows - Integral Clamp - Brass
Zero Backlash - Constant Angular Velocity - Dampens vibration and noise - Tin plate finish
Phosphor Bronze Bellows. Brass Hubs.
Couplings - Bellows - Set Screw - 316 Stainless
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Stainless Steel 303L Bellows. Stainless Steel 316 Hubs.
Couplings - Bellows - Set Screw - Aluminium
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Phosphor Bronze Bellows. Aluminium Hubs.
Couplings - Bellows - Set Screw - Brass with Tin Plate Finish
Shafts - Flexible - Coupling Ends - Open (Ondrives)
Bi-directional flexible shaft couplings.
Hubs: 220 MO7 / Shaft: Steel. Standard bored ends. Keyways can be included in the bores for additional cost.
Couplings - Oldham - Complete - Acetal Disk - Clamp Type
0.06 to 44 Nm. Max Speed: 3000 RPM.
Max Speed: 3000 RPM. Parallel out of line compensation. Temp Range -20 Deg C to +60 Deg C. Oldham couplings are designed to transfer torque between two parallel, but not colinear, shafts. They have three discs, one coupled to the input, one coupled to the output, and a centre disc that is joined to the first two by tongue and grooves. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.
Couplings - Oldham - Complete - Acetal Disk - Set Screw
0.06 to 44 Nm. Max Speed: 3000 RPM.
Max Speed: 3000 RPM. Parallel out of line compensation. Temp Range -20 Deg C to +60 Deg C. Oldham couplings are designed to transfer torque between two parallel, but not colinear, shafts. They have three discs, one coupled to the input, one coupled to the output, and a centre disc that is joined to the first two by tongue and grooves. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.
Couplings - Oldham - Disks for Clamp Style
0.06 to 44 Nm. Max Speed: 3000 RPM.
Disk inserts. Single hubs. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.
Couplings - Oldham - Disks for Set Screw Style
0.06 to 44 Nm. Max Speed: 3000 RPM.
Disk inserts. Single hubs. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.
Couplings - Polyurethane Spider Jaw Type - Complete
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
2.1 to 17 Nm.
Split Type Hub. Preloaded Rubber Spider. Minimal backlash. Choice of 3 different spiders for each size provides for different torque requirements. Hubs and spiders available separately or as a complete unit.
0.45 to 6.44 Nm.
MATERIALS: Hubs - Aluminium, Pins - Hardened Alloy Steel, Socket Head Screws - Alloy Steel, Control-Flex Member - Delrin® 100. Lightweight, low inertia, and no maintenance or lubrication necessary. No change in angular velocity or torque due to misalignment. No end thrust due to torque transmission. Rated torques are with all alignment factors zero. The summation of the three alignment factors should not exceed 50%. The rated torque must be reduced by the summation of the alignment factors. Operating Temperature: -23 deg to +65 deg Celsius.
Couplings - Cross Joint - High Speed
0.3 to 6 N.m. 15000 to 42000 rpm.
Aluminium A2017 Hubs. Stainless Steel SUS304 Spacers. Hardened Steel Bearing Pins. Abrasion Resistant Polyamide Bush. SCM435 Black Coated Steel Cap Screws.
High torque. No backlash. Clamp fixing.
Aluminium A2017 Hubs. Aluminium A2011 Spacer. Stainless Steel 301 Pin. Stainless Steel 303 Disc.
Up to 3600 RPM - Minus 20 to Plus 60 Degrees C. 0.34 to 18 Nm.
Strong, flexible polyurethane or Hyrtel® is cut and tear resistant. Up to 3600 RPM. Urethane: Minus 20 to Plus 60 Degrees C / Hyrtel® : Minus 40 to Plus 100 Degrees C. Precision swaged mechanically crimped hubs. Annealed steel hubs.
Zero backlash, maintenance free, recommended temperature range -10 Deg C to +80 Deg C, electically isolating
Anodised aluminium hubs. Polyamide 6.6 fibreglass re-inforced membrane. Max Speed 12000 RPM. Misalignment - Radial 0.25mm, Axial +/- 0.4mm, Angular 2.5 Deg. Ideal for light duty applications where a compact overall length is necessary. The membrane coupling offers very good misalignment capabilities using a fiberglass reinforced center, which also provides good vibration damping and electrical insulation.
Internal compression spring preloads the ends against axial movement and backlash. Up to 2.8 Nm. Up to 2000 rpm.
Maximum Torque: 2.8 N.m (25 lb.in). Delrin Torque Tube. Aluminium Split Hubs. Do not compress the unit axially during installation. Speeds to 2000 rpm. One piece assembly.
High speed to 30000 rpm. 2.3 to 9.27 Nm.
Spring : 1095 Steel Hubs : Cold Rolled Steel. Operating Temperature : 121 Deg C (250 Deg F). Maximum Speed : 30000 RPM. For CUF15 series the spring diameter is the same as the hub diameter.
0.3 to 3.5 Nm. 3000 to 6000 rpm.
Hubs (UNL18 & 27): Brass CZ 121 Chromate & passivate finish. Hubs (UNL34 and 41):Alum. Alloy 2011 T8 Alocrom finish. Bearing Rings: Black Acetal. Operating Temp. Range: -20°C to +60°C. 10° angular and 1mm radial compensation. Flex-free mechanical action - low bearing loads.
Couplings - Bellows - Clamp - Stainless Steel 0.1 to 10Nm
Stainless steel bellows with Aluminium hub
Couplings - Bellows - Clamp - Stainless Steel 18 to 500Nm
Stainless steel bellows with Aluminium hub up to 60mm Diameter and Steel hub 80mm and over
Couplings - Bellows - Expanding Clamp - Stainless Steel 0.5 to 10Nm
Stainless steel bellows with Aluminium hub
Couplings - Bellows - Set Screw - Stainless Steel 0.1 to 10Nm
Stainless steel bellows with Aluminium hub
Max speed 15000 rpm. Bore tolerance H7. Temperature range minus 30 to plus 120 Deg C.Too many choices?
You have selected to see ALL categories including any of the following words: hubs
Click here to see ONLY THE MOST POPULAR categories including any of the following words: hubs
|
| |||||||||||||||||||||||||
| Select all items starting with... | |||||||||||||||||||||||||
| A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | Or use the category search | ||||||||||||||||
|
| |||||||||||||||||||||||||
Store - Categories Pages
Store Pages
Main Pages on Small Parts and Bearings Website
Add the special offer below directly to your www.smallparts.com.au cart using the "add to order list" button below. The supply will be made along with your other items for no additional delivery charge.
Limit of 4 per customer
----- Advertisement 01598 -----
Site Summary:
Freight Rates Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery. Small Parts and Bearings is part of MBA Group offering a select range from the MBA Group catalogue. Information on this website is Copyright Small Parts and Bearings 1997. All rights reserved. |
The Hobby and Engineering Supplies online store has a huge range of balsa wood, models, planes, helicopters, screws, carbon fibre, adhesives, hobby bearings, castors amd much much more. Hobby and Engineering Supplies are The right mix of business and pleasure.
----- Advertisement 011498 -----