All Items: General Purpose Shafting - Categories


Shafting General Purpose

Hide Pictures

Go to Top  


Shafting - Keyed

Shafting - Keyed

Keyways are cut full length of each bar.

Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00.

Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting


Shafting - Mild Steel

Shafting - Mild Steel

Great axles for low load and low precision applications like trolleys, carts and wheelbarrows.


Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting

Related Information:
Shaft Extenders

Bore Reducers


Rod - Drill - General

Rod - Drill - General

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Chrome vanadium alloy with unfinished ends. Requires heat treating to harden. Small diameters may not be perfectly straight. Heat treating by air, water or oil.

Click for combined categories: All Drill Rod

Related Information:
Silversteel


Shafting - Ground - Silver Steel

Shafting - Ground - Silver Steel

Unhardened silversteel shafting for general purposes. Not suitable for precision bearings until machined to correct tolerances and hardened.

See also drill rod. Drill Rod.

Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting

Related Information:
Shaft Extenders

Bore Reducers


Rod - Drill Blanks

Rod - Drill Blanks

Made of hardened high speed steel.

Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.

Click for combined categories: All Drill Rod


Shafts - Flexible - Panel Mount - Cased

Shafts - Flexible - Panel Mount - Cased

See PDF file at bottom of internet page for Performance Data.

Click for combined categories: All Flexible Shaft

Related Information:
Remote Control Nomenclature


Shafts - Flexible - Panel Mount - Open

Shafts - Flexible - Panel Mount - Open

See PDF file at bottom of internet page for Performance Data.

Click for combined categories: All Flexible Shaft

Related Information:
Remote Control Nomenclature


Rod - Drill - A-2 Air Hardening

Rod - Drill - A-2 Air Hardening

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Air hardening. Maximum abrasion resistance. 65 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Click for combined categories: All Drill Rod


Rod - Drill - O-1 Oil Hardening

Rod - Drill - O-1 Oil Hardening

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Click for combined categories: All Drill Rod


Rod - Drill - Oil Hardening - 480 Series

Rod - Drill - Oil Hardening - 480 Series

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

General purpose tool steel with good wear resistance, toughness and machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Click for combined categories: All Drill Rod


Rod - Drill - S-7 Air Hardening

Rod - Drill - S-7 Air Hardening

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Air hardening molybdenum, chromium, shock resisting. High impact strength with moderate wear resistance. 95 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Click for combined categories: All Drill Rod


Rod - Drill - W-1 Water Hardening

Rod - Drill - W-1 Water Hardening

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

High abrasion resistance and high toughness when hardened. 100 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

Click for combined categories: All Drill Rod


Castors

Hide Pictures

Go to Top  


Castors - Plate - General Purpose - Fixed

Castors - Plate - General Purpose - Fixed


Click for combined categories: All Castors


Castors - Plate - General Purpose - Swivel

Castors - Plate - General Purpose - Swivel


Click for combined categories: All Castors


Castors - Plate - General Purpose - Swivel with Brake

Castors - Plate - General Purpose - Swivel with Brake


Click for combined categories: All Castors


Castors - Stud - General Purpose - Swivel

Castors - Stud - General Purpose - Swivel


Click for combined categories: All Stud Type Castors


Leadscrews

Hide Pictures

Go to Top  


Leadscrew Assemblies - General Purpose

Leadscrew Assemblies - General Purpose

Nut: Self-lubricating Acetal / Leadscrew: 303 Stainless Steel with TFE extended life coating. Positional Repeatability: 0.0013mm. Lead Accuracy: 0.0006mm/mm. For applications not requiring anti-backlash and wear compensation. The secure mounting and convenience of a circular flange is standard on the B nuts.

Click for combined categories: All Leadscrew Assemblies


Lubricants General Purpose

Hide Pictures

Go to Top  


Lubricants - General

Lubricants - General

Various brands and types. Includes Inox, Lanox, Anti-Seize, Cutting Fluid, Chain Lube, Moly Lube, Food Grade Grease, PTFE Lubes, Silicone and more

Some items in this category are marked as only available for collection. Includes high temperature and food grade lubes. Battery Conditioner - Oils - Moisture Inhibitor - WD - Valve and Oring Lubricant.

Click for combined categories: All Lubricants


Tools General Purpose

Hide Pictures

Go to Top  


Tools - General

Tools - General

Butane Torch, Inspection Mirror, Mini Sandblaster, Nibbling Tool, Plastic Scriber, Pick Up Tool Set, Hex Driver Handle for Insert Bits

X-Acto Knife Sets - Pin Vises - Screw Pitch Gauges and more.

Click for combined categories: All Tools


Tools - Paint

Tools - Paint

Includes airbrush, compressor, brushes, paint stand and alligator clips.

Click for combined categories: All Tools


Tools - Pliers

Tools - Pliers

Pliers, multi tool

Lengths shown are based on standard stock but may vary.

Click for combined categories: All Tools


Tools - Punches

Tools - Punches

Number punch and letter punch sets

Lengths shown are based on standard stock but may vary.

Click for combined categories: All Tools


Tools - Tweezers

Tools - Tweezers

Selection of tweezers for those fiddly jobs.

Click for combined categories: All Tools


Tools - Chain Breaker

Tools - Chain Breaker

Used to break roller chain at the pins

Balsa Stripper, Razor Planes and Blades.

Click for combined categories: All Tools


Tools - Geiger Range

Tools - Geiger Range

Geiger tool range. Ask for a brochure for the latest specials.

Note some items are bulky and may require a special quote for freight. We will contact you prior to processing your order if the fr4eight charge needs revision.

Click for combined categories: All Tools


Tools - Nut Drivers

Tools - Nut Drivers

Includes socket wrench for 0-80 size screws

Lengths shown are based on standard stock but may vary.

Click for combined categories: All Tools


Tools - Pin Vises

Tools - Pin Vises

Lengths shown are based on standard stock but may vary.

Click for combined categories: All Tools


Isolators

Hide Pictures

Go to Top  


Mounts - Vibration - Isolation Pads - General Purpose

Mounts - Vibration - Isolation Pads - General Purpose

For installation of industrial machinery where the ratio of shear loads to vertical loads is less than or equal to 1 to 5.

Base is unthreaded. The stud rests on the pad and is not threaded in or fastened to the pad. Self aligning feature compensates for uneven floors without sacrificing stability. Scientifically designed diamond suction cells of the neoprene insert firmly anchor the machine to the floor. Recommended for a wide range of industrial machinery and equipment where simple precise leveling is required. 25.4mm level adjustment.

Click for combined categories: All Isolation Pad Mounts


Magnets Alnico

Hide Pictures

Go to Top  


Magnets - Alnico - Horseshoe

Magnets - Alnico - Horseshoe

General purpose horseshoe magnet


Click for combined categories: All Magnets

Click for combined categories: All Alnico Magnets


Tools General Purpose

Hide Pictures

Go to Top  


Tools - Nut Driver Set

Tools - Nut Driver Set

Lengths shown are based on standard stock but may vary.

Click for combined categories: All Tools


Hooks

Hide Pictures

Go to Top  


Slings - Wire Rope - Permaloc®

Slings - Wire Rope - Permaloc®

For general purpose lifting in environments too rugged for synthetic slings. Tuff-Tag identification on every sling for capacity ratings.


O-Rings

Hide Pictures

Go to Top  


O-Rings - Nitrile Rubber

O-Rings - Nitrile Rubber

General purpose.

Temperature Range: -30oC to +90oC. Nitrile: Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids.

Click for combined categories: All O-Rings


Bushes Plastic

Hide Pictures

Go to Top  


Bushes - Plastic - Iglidur G - Flanged

Bushes - Plastic - Iglidur G - Flanged

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.

Click for combined categories: All Plastic Bushes

Click for combined categories: All Flanged Plastic Bushes


Bushes - Plastic - Iglidur G - Unflanged

Bushes - Plastic - Iglidur G - Unflanged

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.

Click for combined categories: All Plastic Bushes

Click for combined categories: All Unflanged Plastic Bushes


Bar

Hide Pictures

Go to Top  


Tool Steel - 496 Oil Hardening - Flat Stock

Tool Steel - 496 Oil Hardening - Flat Stock

General purpose tool steel with good wear resistance, durability and machinability

Dimensionally stable chromium, tungsten and vanadium electric furnace toolsteel can be used for intricate work. Low 787 to 815 oC (1450-1500 F) hardening range makes it easy to harden. Fully spheroidised and annealed for uniform carbide size and easy machining. Each piece is individually wrapped and clearly marked with size, analysis and correct hardness and tempering information. Edge squareness 0.003 mm per mm. Finish is 0.0008mm (0.000032 inch).

Oil Seals

Hide Pictures

Go to Top  


Oil Seals - Nitrile Rubber

Oil Seals - Nitrile Rubber

DIN 3760 - General purpose grease and oil sealing. Note - metal cased and rubber cased seals may be interchanged at our discretion. If one or the other is specifivally required please let us know when ordering.

Operating Temp. Range: -30oC to +90oC. The rubber elastomer outer covering tolerates thermal expansion as well as roughness in the housing bore. Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids.

Click for combined categories: All Oil Seals


Strip

Hide Pictures

Go to Top  


Strip - Soft Metal Packs

Strip - Soft Metal Packs

For general hobby applications. This brass strip is annealed soft to make it easier to bend. Brass.

300mm lengths. Not recommended for heavy duty applications. For use with bearings we suggest you use items from the category - Shafting - Ground.

Tube and Tubing

Hide Pictures

Go to Top  


Tube - Round - Soft Metal Packs

Tube - Round - Soft Metal Packs

For general hobby applications. This tube is annealed soft to make it easier to bend. Copper, brass and aluminium,

300mm lengths. Not recommended for heavy duty applications. For use with bearings we suggest you use items from the category - Shafting - Ground.

Click for combined categories: All Metal Tube


Engineering and Hobby Rod

Hide Pictures

Go to Top  


Rod - Round - Soft Metal Packs

Rod - Round - Soft Metal Packs

For general hobby applications. This rod is annealed soft to make it easier to bend. Copper, brass and aluminium,

300mm lengths. Not recommended for heavy duty applications. For use with bearings we suggest you use items from the category - Shafting - Ground.

Click for combined categories: All Metal Rod


Tube and Tubing

Hide Pictures

Go to Top  


Tube - Round - Stainless Steel

Tube - Round - Stainless Steel

Hollow round tubing for general hobby applications.

For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Click for combined categories: All Metal Tube

Related Information:
Stainless Steel Properties


Engineering and Hobby Rod

Hide Pictures

Go to Top  


Rod - Round - Aluminium

Rod - Round - Aluminium

For general hobby applications.

NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Click for combined categories: All Metal Rod


Rod - Round - Brass

Rod - Round - Brass

For general hobby applications.

NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Click for combined categories: All Metal Rod


Rod - Round - Stainless Steel

Rod - Round - Stainless Steel

For general hobby applications.

NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.

Click for combined categories: All Metal Rod


Tube and Tubing

Hide Pictures

Go to Top  


Tube - Round - Aluminium

Tube - Round - Aluminium

Hollow round tubing for general hobby applications.

For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Click for combined categories: All Metal Tube

Related Information:
Aluminium Properties


Tube - Round - Brass

Tube - Round - Brass

Hollow round tubing for general hobby applications.

For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Click for combined categories: All Metal Tube

Related Information:
Brass Properties


Tube - Round - Copper

Tube - Round - Copper

Hollow round tubing for general hobby applications.

For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.

Click for combined categories: All Metal Tube


Square Shaft

Hide Pictures

Go to Top  


Shafting - Linear - Square

Shafting - Linear - Square


Hobby Shafting

Hide Pictures

Go to Top  


Shafting - Ground - Hobby - Steel

Shafting - Ground - Hobby - Steel

Silversteel shafting for hobbies. Not suitable for precision bearings.

Suitable for use with plastic gears, bushes, couplings etc. Not recommended for use with precision steel or stainless steel bearings. Some sizes have special features such as serrations or small barbs (noted in description). Unground ends. Ideal for axles in robotic applications and educational projects.

Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting

Related Information:
Shaft Extenders

Shaft Assortments


Shafting Aluminium

Hide Pictures

Go to Top  


Shafting - Aluminium

Shafting - Aluminium

Drylin aluminium shafting is recommended for use with Igubal Drylin bearings or Frelon lined bearings only.

Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.

Click for combined categories: All Shafting

Click for combined categories: All Aluminium Shafting


Shafting - Pipe - Aluminium

Shafting - Pipe - Aluminium

Recommended for use with Igubal Drylin bearings only.

Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and Less than 9.

Click for combined categories: All Pipe Shaft

Click for combined categories: All Metal Tube


Shafting - Supported - Pre-Drilled - Aluminium

Shafting - Supported - Pre-Drilled - Aluminium

For Drylin Bearings.

Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and less than 9.

Click for combined categories: All Shafting

Click for combined categories: All Aluminium Shafting


Shafting Precision Ground

Hide Pictures

Go to Top  


Shafting - Ground - Cold Rolled Steel

Shafting - Ground - Cold Rolled Steel

Cold rolled steel with saw cut ends and smooth finish


Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Chrome Plated

Shafting - Ground - Precision - Chrome Plated

Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Hardened and recommended for use with precision bearings. Ends are not plated.


Shafting - Ground - Precision - Chrome Vanadium Alloy

Shafting - Ground - Precision - Chrome Vanadium Alloy

Precision ground shafting. Ck53 / Cf53 Chrome Vanadium Alloy. Hardened and recommended for use with precision bearings.


Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - High Carbon Steel

Shafting - Ground - Precision - High Carbon Steel

Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.


Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Stainless 17-4PH Grade Hardened

Shafting - Ground - Precision - Stainless 17-4PH Grade Hardened

Precision ground shafting. 17-4PH grade. Hardened and recommended for use with precision bearings.


Click for combined categories: All Shafting

Click for combined categories: All Stainless Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Stainless 303 Grade

Shafting - Ground - Precision - Stainless 303 Grade

Precision ground shafting.


Click for combined categories: All Shafting

Click for combined categories: All Stainless Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Stainless 316 Grade

Shafting - Ground - Precision - Stainless 316 Grade

Precision ground shafting.


Click for combined categories: All Shafting

Click for combined categories: All Stainless Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Stainless 416 Grade Hardened

Shafting - Ground - Precision - Stainless 416 Grade Hardened

Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.


Click for combined categories: All Shafting

Click for combined categories: All Stainless Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Stainless 420 Grade Hardened

Shafting - Ground - Precision - Stainless 420 Grade Hardened

Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.


Click for combined categories: All Shafting

Click for combined categories: All Stainless Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Stainless 440C Grade Hardened

Shafting - Ground - Precision - Stainless 440C Grade Hardened

Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.


Click for combined categories: All Shafting

Click for combined categories: All Stainless Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Titanium - Ti-Gr2/TA1

Shafting - Ground - Precision - Titanium - Ti-Gr2/TA1


Click for combined categories: All Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Ground - Precision - Titanium - Ti-Gr5/TC4

Shafting - Ground - Precision - Titanium - Ti-Gr5/TC4


Click for combined categories: All Shafting

Related Information:
Shaft Extenders

Bore Reducers


Shafting - Pre Drilled and Tapped - High Carbon Steel

Shafting - Pre Drilled and Tapped - High Carbon Steel

For use with rail supports and open linear bearings

Straightness: 0.1 mm / mtr.

Click for combined categories: All Shafting

Click for combined categories: All Steel Shafting


Shafting - Pre Drilled and Tapped - Stainless Steel Steel

Shafting - Pre Drilled and Tapped - Stainless Steel Steel

For use with rail supports and open linear bearings


Click for combined categories: All Shafting

Click for combined categories: All Stainless Shafting


Shafting Hollow

Hide Pictures

Go to Top  


Shafting - Pipe - AISI52100 Steel

Shafting - Pipe - AISI52100 Steel

AISI 52100 Steel Hardened to HRC 58-62. Straightness 0.0003 mm / mm. Ideal for design weight reduction. Note! ID of pipe shaft may be up to 1mm undersize. Other lengths may be available on request however a surcharge for special sizing will apply and extended delivery times can be expected (if available).

Click for combined categories: All Pipe Shaft

Click for combined categories: All Metal Tube


Shafting Aluminium

Hide Pictures

Go to Top  


Shafting - Aluminium - Ceramic Coated

Shafting - Aluminium - Ceramic Coated

Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.

Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.

Click for combined categories: All Shafting

Click for combined categories: All Aluminium Shafting


Shafting - Aluminium - Ceramic Coated - Tapped

Shafting - Aluminium - Ceramic Coated - Tapped

Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.

Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.

Click for combined categories: All Shafting

Click for combined categories: All Aluminium Shafting


Shafting Precision Ground

Hide Pictures

Go to Top  


Shafts - Idler

Shafts - Idler

Ready made precision ground idler shafts.

Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design.

Shafts - Pinion

Shafts - Pinion


Click for combined categories: All Shafts


Supports - Block

Supports - Block

For linear shafting.

Material: Aluminium.

Click for combined categories: All Supports


Rail Supports - Without Shaft

Rail Supports - Without Shaft

For mounting of linear shafting.

Shafting sold separately. Support is made from aluminium.

Click for combined categories: All Shaft Supports

Related Information:
Linear Bearing in Housing

Linear Bearings


Rail Supports - With Shaft

Rail Supports - With Shaft

Includes linear shafting.

Includes shaft to h6 tolerances. Support is made from aluminium.

Click for combined categories: All Shaft Supports

Related Information:
Linear Bearings


Supports - Flanged Four Bolt

Supports - Flanged Four Bolt

For linear shafting.

Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.

Click for combined categories: All Supports


Supports - Flanged Two Bolt

Supports - Flanged Two Bolt

For linear shafting.

Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.

Click for combined categories: All Supports


Supports - Pedestal Two Bolt

Supports - Pedestal Two Bolt

For linear shafting.

Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.

Click for combined categories: All Supports


Rail Supports - With Shaft - One Piece

Rail Supports - With Shaft - One Piece

One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.

Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments.

Click for combined categories: All Shaft Supports

Related Information:
Linear Bearings

Frelon Linear Bearings


Assortments

Hide Pictures

Go to Top  


Assortment Kits - Various

Assortment Kits - Various

Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Shim - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins


Splined Shafts and Bushes

Hide Pictures

Go to Top  


Splined Shafts - Steel

Splined Shafts - Steel

Externally splined shafting. Bushes not included. Match with same size splined bushes.

Match bushes and shafts by Major Diameter. Steel on Steel is not meant for sliding applications. Steel on Bronze is OK for intermittent sliding under load.

Click for combined categories: All Splined Shafts

Related Information:
Combined Splined Bushes List


Splined Shafts - Stainless Steel

Splined Shafts - Stainless Steel

Externally splined shafting. Bushes not included. Match with same size splined bushes.

Match bushes and shafts by Major Diameter. Steel on Steel is not meant for sliding applications. Steel on Bronze is OK for intermittent sliding under load.

Click for combined categories: All Splined Shafts

Related Information:
Combined Splined Bushes List


Flexible Shaft

Hide Pictures

Go to Top  


Shafts - Flexible - Coupling Ends - Open - Mild Steel

Shafts - Flexible - Coupling Ends - Open - Mild Steel

Flexible shafting with coupling ends ready to attach to a fixed shaft.

1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm.

Click for combined categories: All Flexible Shaft

Related Information:
Remote Control Nomenclature


Shafts - Flexible - Coupling Ends - Open - Stainless Steel

Shafts - Flexible - Coupling Ends - Open - Stainless Steel

Flexible shafting with coupling ends ready to attach to a fixed shaft. 303 Stainless Steel.

1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm.

Click for combined categories: All Flexible Shaft

Related Information:
Remote Control Nomenclature


Housings - Linear with Bearings

Hide Pictures

Go to Top  


Housings - Linear - Square

Housings - Linear - Square

Used to maintain radial integrity and eliminate the need for parallel shafting.

Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads.

Click for combined categories: All Linear Bearing Housings


Adhesives

Hide Pictures

Go to Top  


Adhesives - General

Adhesives - General

Molytec, Loctite, Pacer, Dow Corning, 3M. Includes silicone sealant, gasket adhesive, canopy glue, belt conditioner and electronic tak-pak.


Click for combined categories: All Adhesives


Dials

Hide Pictures

Go to Top  


Dials - General Indexes

Dials - General Indexes

Use with drum and disc dials.


Click for combined categories: All Dials


Switches

Hide Pictures

Go to Top  


Switches - General

Switches - General


Click for combined categories: All Switches


Books

Hide Pictures

Go to Top  


Books - Hobby - General

Books - Hobby - General

Tips and tricks, maintenance and how-to guides.

Styrene modelling, biodiesel, Tamiya catalogue, RC tuning.

Click for combined categories: All Books


Bearings Linear

Hide Pictures

Go to Top  


Bearings - Linear - Ball - Open

Bearings - Linear - Ball - Open

For running on shafts supported by a rail along their length.

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.

Click for combined categories: All Linear Ball Bearings


Games General

Hide Pictures

Go to Top  


Games - Board

Games - Board

Gravity Trap, Squatter and Design Your Own Board Game.


Click for combined categories: All Games and Gadgets


Games - Children

Games - Children

Batik, bendomino, bingory, catz ratz and batz, chekov, chicky boom, coocoo, cosmic cows, dominoes, froggy boogie.

Quality wooden games and more. Goblett Gobblers - Design Your Own Board Game - Pengoloo. Kangaroos and Koalas - Quack - Quoridor - Speedy Eddie. Katamino - Splash Attack - Sputnik - Think Twice. Magic Pen - Zimbbos - Zippy Dice.

Click for combined categories: All Games and Gadgets


Games - Educational

Games - Educational

Crystals, science kits, space race and more

Katamino - Splash Attack - Sputnik - Think Twice. Magic Pen - Zimbbos - Zippy Dice.

Click for combined categories: All Games and Gadgets


Games - Magnetic

Games - Magnetic

Magnetic games


Click for combined categories: All Games and Gadgets


Games - Memory

Games - Memory

Brainbox Around The World, Maths and Nature. Memory Cards.


Click for combined categories: All Games and Gadgets


Games - Strategy

Games - Strategy

Strategy Games including Wooden and other games. Ideal gifts for thinking people.

Gobblet on the Go - Ringgz - Double Shutter - Eye of Horus - Khet - Tower of Kadesh - Giza - Dividends. Jumping Java - Logan Stones - Hive - Army of Frogs - Quarto - Quixo - Quoridor - Batik - Pylos. Skybridge - Inside - Eclipse - Gipf - Zertz - Dvonn - Yinsh - Punct - Tamsk - Abalone - Pentago - Columns. Trinidad - Fire and Ice - Cityscape - Poison Pot - Zaroc - Megalith - Tantrix - Yikers.

Click for combined categories: All Games and Gadgets


Fasteners General

Hide Pictures

Go to Top  


Fasteners - Interlock

Fasteners - Interlock

Specially designed bolts, nuts and washers that have step grooves which lock as you tighten. Almost impossible to loosen with a regular wrench.

Antivibration - loosening resistant - theft resistant. Patented design features bolt, nut and washer with unique wedge shape on opposing sides. Bolts are quickly and easily tightened and loosened using the specially designed trivalent chromium plated steel socket wrench. Fasteners are carbon steel.

Hobby Servo Motors

Hide Pictures

Go to Top  


Servo Motor - Hobby - General

Servo Motor - Hobby - General

For cars, planes, boats and helicopters. JR, Spektrum, Futaba and Hitec

Gear Strength: Using nylon as a base, Karbonite gears are 4x the strength, Metal gears 16x and Titanium Alloy 48x.

Click for combined categories: All Hobby Servo Motors


Springs General

Hide Pictures

Go to Top  


Posts - Spring

Posts - Spring

Related Information:
Metre Length Extension Springs


Sets

Hide Pictures

Go to Top  


Tools - Sets

Tools - Sets

General tool sets, screwdriver sets, tap sets, dies sets.

Click for combined categories: All Tools


Mounts Cylindrical

Hide Pictures

Go to Top  


Mounts - Cylindrical - Special Purpose

Mounts - Cylindrical - Special Purpose

Vibration dampening


Click for combined categories: All Cylindrical Mounts


Pins - General

Hide Pictures

Go to Top  


Pins - Hitch - External

Pins - Hitch - External

Similar to R-Clips, but designed for both arms to fit around a shaft groove rather thand having one arm through a bored hole.



Select all items starting with...
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9



Store - Categories Pages

Go to Top





Store Pages

Go to Top





Main Pages on Small Parts and Bearings Website




Go to Top

Site Summary

Freight Rates
Terms and Conditions
Privacy Policy

Small Parts and Bearings offers 154991 products in 3674 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We ship by traceable courier only (no standard post) and we have excellent Freight Rates within Australia and worldwide.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts and Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts and Bearings 1997. All rights reserved.