Categories for: flat washers rubber
Flat red vulcanised fibre washers. Black available on request and sufficient quantity.
Operating temperature up to 105 Deg C. Tensile strength 6 kg/mm2. Elongation up to 19 percent. Shrinkage up to 3 percent thickness. Water absorption 4 to 70 percent after 24 hours. Density 1 to 1.45 g/cm.
Washers - Flat - Brass - Commercial
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
Washers - Flat - Sintered Bronze - Precision
Flat thrust washers made from oil impregnated sintered bronze
Washers - Flat - Stainless Steel - Commercial
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
Washers - Flat - Titanium - CP Grade 1
Flat washers. CP Grade 1 Titanium.
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
Washers - Flat - Titanium - Grade 5
Flat washers. 6AL-4V (Grade 5) High strength titanium alloy.
6AL-4V (Grade 5) High strength titanium alloy, used in critical aircraft structural components. UNS R56400. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
Washers - Nord Lock - 316 Stainless
Supplied in pairs
Steel: Hardness HRA 75±3% (HRC48) Passivated Zinc Plated. ALWAYS LUBRICATE FASTENERS BEFORE REUSING. When reusing fasteners the friction is always higher. When tightening, a 20% higher torque should be applied than if tightening against a flat washer. Also see Lockrite and Disc Lock washers.
Washers - Nord Lock - Zinc Plated
Supplied in pairs
Steel: Hardness HRA 75±3% (HRC48) Passivated Zinc Plated. ALWAYS LUBRICATE FASTENERS BEFORE REUSING. When reusing fasteners the friction is always higher. When tightening, a 20% higher torque should be applied than if tightening against a flat washer. Also see Lockrite and Disc Lock washers.
Composite bearing material conisting of 3 bonded layers; Steel backing strip bonded with porous sinter bronze interlayer which is impregnated and overlaid with polytetrafluroethylene(PTFE) containing a mixture of inorganic filers and special polymer fibre
Operating Temperature -200 Degrees to 280 Degrees Celsuis. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free.
Composite bearing material consisting of 3 bonded layers. Steel backing strip bonded with porous sintered bronze interlayer which is impregnated and overlaid with polytetrafluroethylene (PTFE) and lead bearing material.
Operating temperature - 200 Degrees to 280 degrees celsius. Maximum load 250N per mm2. Requires no lubrication. Provides maintenance free operaton. Exhibits low wear rate. Seizure resistant. High static and dynamic load capacity, Good frictional properties with negligible stick-slip. Resists solvents. No water absorption. Electrically conductive and shows no electrostatic effects. Compact and light. Good embedability and is tolerant of dusty environments.
Composite bearing material conisting of 3 bonded layers; Steel backing strip bonded with porous sinter bronze interlayer which is impregnated and overlaid with pigmented acetal copolymer bearing material.
Operating temperature -40 Degrees to 120 Degrees Celsius. Provides maintainance free operation. Exhibits low wear rate. Seizure resistant. High Static and Dynamic Load capacity. Good frictional prperties, No water absorption, Compact and Light, Suitable for rotating, oscillating, reiprocating and sliding movements.
Washers - Thrust - Stainless Steel and PTFE
Composite bearing material conisting of 3 bonded layers; Steel backing strip bonded with porous sinter bronze interlayer which is impregnated and overlaid with polytetrafluroethylene(PTFE) containing a mixture of inorganic filers and special polymer fibre
Operating Temperature -200 Degrees to 280 Degrees Celsuis. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free.
Washers - Self Aligning - Components - Hardened Steel
Spherical Seat Washers
Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3 Degree of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
Washers - Self Aligning - Components - Stainless Steel
Spherical Seat Washers
AISI 303 Stainless Steel. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3 Degree of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
Washers - Self Aligning - Sets - Hardened Steel
Spherical Seat Washers
Hardened steel 9 S Mn Pb 28 K DIN 6319. Max Shaft Size Shown will allow 3 Degree of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
Washers - Self Aligning - Sets - Stainless Steel
Spherical Seat Washers
AISI 303 Stainless Steel. Max Shaft Size Shown will allow 3 Degree of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
For countersunk screws.
Nickel Plated Brass.
Washers - Lock - Internal Tooth - Spring Steel
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
Washers - Lock - Internal Tooth - Stainless Steel
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
Washers - Lock - Tabbed - Heavy Duty
Heavy duty WH / TW Series for bearing locknuts.
Carbon spring steel. Use with NH series locknuts.
Washers - Lock - Tabbed - MB Series
Standard MB series lockwasher for use with bearing locknuts.
Carbon spring steel. Use with N/AN and NL series locknuts.
Washers - Lock - Tabbed - Thin
Thin section - use with NT series locknuts.
Use with NT series locknuts.
Also see Nord Lock and Lockrite washers
Stainless Grade Grade A2 302/316 18-8. Vibration-proof self tightening structural locking device. Maximum Working Temp: +430°C. DISC-LOCK® has outperformed all other types of loose, washered, threaded or pinned systems. in a wide range of high stress, corrosive, and vibration sensitive applications.
Supplied in pairs.
Also see Nordlock and Disk Lock washers.
Washers - Disc Spring - Plastic
Also known as belleville washers.
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb® material.
Bearings - Thrust - Ball - Flat Race Type
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Bearings - Thrust - Ball - Washers Only
Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.
Stainless Steel Washers are hardened to HRC38.42. Carbon Steel Washers are hardened to RC59.61.
Washers - Disc Spring - Carbon Steel
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093.
Washers - Disc Spring - Stainless Steel
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093.
Screws - Self Drilling - Hex Head - With Washers
With bonded neoprene washer. Galvanised for corrosion resistance.
Neoprene and natural rubber gaskets for sealing doors and many other applications.
Meet NEMA 12 to NEMA 4X applications. Easy to install with self adhesive backing. Easily cut to size and shaped for many applications. Fibre backing helps to eliminate stretching and helps to maintain seal in position.
Pins - Hammer Drive - Flat Head
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
Flat arbor shim washers with keyway groove.
Polycarbonate pulleys for flat belts 6mm or 6.35mm wide.
Aluminium Knurled Inserts. Gold Iridite Brass Knurled Inserts. Set Screw Locking.
Pulleys - Flat Belt - Idler - Heavy Duty
Complete with Needle Roller Bearing.
Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.
Magnetic Vinyl Sheets and Magnetic Rubber Strip
Female 4-40 UNC thread in head allows for secure fixing of studs to a panel.
Each screw comes with two flat washers, 1one lock washer and one hex nut. Yellow chromate zinc finish.
Mounts - Spring - Eliptical Leaf - Light Duty
Lightweight NATO approved X Mounts
The 6kg mount is designed to isolate lightweight equipment like computers, printers, electronics panels etc from shock and vibration. All vibration modes and stiffness indicated are for mounting on a flat horizontal surface where vertical indicates the downwards stiffness and horizontal indicates stiffness alonf the horizontal plane. Horizontal 2 figures are for inverted mounting. 304 Stainless leaves, nylon and stainless washers and polymer damping compound. Temperature range +10 Deg C to + 30 Deg C.
Bearings - Thrust - Ball - Retainer and Balls Only
Match with thrust washers of the same bore and OD.
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
Specially designed bolts, nuts and washers that have step grooves which lock as you tighten. Almost impossible to loosen with a regular wrench.
Antivibration - loosening resistant - theft resistant. Patented design features bolt, nut and washer with unique wedge shape on opposing sides. Bolts are quickly and easily tightened and loosened using the specially designed trivalent chromium plated steel socket wrench. Fasteners are carbon steel.
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Shim - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
Knobs - Ball - Threaded - Wrench Flats and Knob-Lok
Unique Knob-Lok features a nylon locking element that resists vibration and prevents back-off
Perfect for high vibrational applications.
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
Socket Set Screws - Flat Ball Tip
Grub screws with a rotating flat tip. The ball can rotate up to 9 Deg. to fasten the object securely.
Tool Steel - 496 Oil Hardening - Flat Stock
General purpose tool steel with good wear resistance, durability and machinability
Dimensionally stable chromium, tungsten and vanadium electric furnace toolsteel can be used for intricate work. Low 787 to 815 Deg C (1450-1500 F) hardening range makes it easy to harden. Fully spheroidised and annealed for uniform carbide size and easy machining. Each piece is individually wrapped and clearly marked with size, analysis and correct hardness and tempering information. Edge squareness 0.003 mm per mm. Finish is 0.0008mm (0.000032 inch).
Couplings - Miniflex - Stainless Steel Flat Wire Type
Light metal hubs and stainless steel wire. Up to 120 Deg C.
Screws - Socket - Button - Stainless Steel - With Ventilation Hole
304 Stainless Steel. Remove trapped gases between the threads through the washer with ventilation grooves.
May be used in vacuum chamber applications in clean rooms, Flat Panel Displays, Semiconductor production equipment and devices. All clean washed, preventing the inclusion of oil and foreign particles.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Brass, steel, aluminum and stainless.
Nuts - Hexagonal - Washer Faced - Titanium
6AL-4V (Grade 5) High strength titanium alloy.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. 6AL-4V (Grade 5) High strength titanium alloy, used in critical aircraft structural components. UNS R56400.Too many choices?
You have selected to see ALL categories including any of the following words: flat washers rubber
|
| |||||||||||||||||||||||||
| Select all items starting with... | |||||||||||||||||||||||||
| A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | Or use the category search | ||||||||||||||||
|
| |||||||||||||||||||||||||
