Categories for: flat washers metallic and plastic
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
Washers - Flat - Brass - Commercial
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
Washers - Flat - Sintered Bronze - Precision
Flat thrust washers made from oil impregnated sintered bronze
Washers - Flat - Stainless Steel - Commercial
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
Washers - Flat - Titanium - CP Grade 1
Flat washers. CP Grade 1 Titanium.
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
Washers - Flat - Titanium - Grade 5
Flat washers. 6AL-4V (Grade 5) High strength titanium alloy.
6AL-4V (Grade 5) High strength titanium alloy, used in critical aircraft structural components. UNS R56400. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
Flat red vulcanised fibre washers. Black available on request and sufficient quantity.
Operating temperature up to 105 Deg C. Tensile strength 6 kg/mm2. Elongation up to 19 percent. Shrinkage up to 3 percent thickness. Water absorption 4 to 70 percent after 24 hours. Density 1 to 1.45 g/cm.
Composite bearing material conisting of 3 bonded layers; Steel backing strip bonded with porous sinter bronze interlayer which is impregnated and overlaid with pigmented acetal copolymer bearing material.
Operating temperature -40 Degrees to 120 Degrees Celsius. Provides maintainance free operation. Exhibits low wear rate. Seizure resistant. High Static and Dynamic Load capacity. Good frictional prperties, No water absorption, Compact and Light, Suitable for rotating, oscillating, reiprocating and sliding movements.
Washers - Nord Lock - 316 Stainless
Supplied in pairs
Steel: Hardness HRA 75±3% (HRC48) Passivated Zinc Plated. ALWAYS LUBRICATE FASTENERS BEFORE REUSING. When reusing fasteners the friction is always higher. When tightening, a 20% higher torque should be applied than if tightening against a flat washer. Also see Lockrite and Disc Lock washers.
Washers - Nord Lock - Zinc Plated
Supplied in pairs
Steel: Hardness HRA 75±3% (HRC48) Passivated Zinc Plated. ALWAYS LUBRICATE FASTENERS BEFORE REUSING. When reusing fasteners the friction is always higher. When tightening, a 20% higher torque should be applied than if tightening against a flat washer. Also see Lockrite and Disc Lock washers.
Washers - Disc Spring - Plastic
Also known as belleville washers.
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb® material.
Composite bearing material conisting of 3 bonded layers; Steel backing strip bonded with porous sinter bronze interlayer which is impregnated and overlaid with polytetrafluroethylene(PTFE) containing a mixture of inorganic filers and special polymer fibre
Operating Temperature -200 Degrees to 280 Degrees Celsuis. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free.
Composite bearing material consisting of 3 bonded layers. Steel backing strip bonded with porous sintered bronze interlayer which is impregnated and overlaid with polytetrafluroethylene (PTFE) and lead bearing material.
Operating temperature - 200 Degrees to 280 degrees celsius. Maximum load 250N per mm2. Requires no lubrication. Provides maintenance free operaton. Exhibits low wear rate. Seizure resistant. High static and dynamic load capacity, Good frictional properties with negligible stick-slip. Resists solvents. No water absorption. Electrically conductive and shows no electrostatic effects. Compact and light. Good embedability and is tolerant of dusty environments.
Washers - Thrust - Stainless Steel and PTFE
Composite bearing material conisting of 3 bonded layers; Steel backing strip bonded with porous sinter bronze interlayer which is impregnated and overlaid with polytetrafluroethylene(PTFE) containing a mixture of inorganic filers and special polymer fibre
Operating Temperature -200 Degrees to 280 Degrees Celsuis. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free.
Washers - Self Aligning - Components - Hardened Steel
Spherical Seat Washers
Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3 Degree of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
Washers - Self Aligning - Components - Stainless Steel
Spherical Seat Washers
AISI 303 Stainless Steel. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3 Degree of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
Washers - Self Aligning - Sets - Hardened Steel
Spherical Seat Washers
Hardened steel 9 S Mn Pb 28 K DIN 6319. Max Shaft Size Shown will allow 3 Degree of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
Washers - Self Aligning - Sets - Stainless Steel
Spherical Seat Washers
AISI 303 Stainless Steel. Max Shaft Size Shown will allow 3 Degree of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
For countersunk screws.
Nickel Plated Brass.
Washers - Lock - Internal Tooth - Spring Steel
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
Washers - Lock - Internal Tooth - Stainless Steel
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
Washers - Lock - Tabbed - Heavy Duty
Heavy duty WH / TW Series for bearing locknuts.
Carbon spring steel. Use with NH series locknuts.
Washers - Lock - Tabbed - MB Series
Standard MB series lockwasher for use with bearing locknuts.
Carbon spring steel. Use with N/AN and NL series locknuts.
Washers - Lock - Tabbed - Thin
Thin section - use with NT series locknuts.
Use with NT series locknuts.
Also see Nord Lock and Lockrite washers
Stainless Grade Grade A2 302/316 18-8. Vibration-proof self tightening structural locking device. Maximum Working Temp: +430°C. DISC-LOCK® has outperformed all other types of loose, washered, threaded or pinned systems. in a wide range of high stress, corrosive, and vibration sensitive applications.
Supplied in pairs.
Also see Nordlock and Disk Lock washers.
Bearings - Thrust - Ball - Flat Race Type
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Pins - Hammer Drive - Flat Head
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
Bearings - Thrust - Ball - Washers Only
Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.
Stainless Steel Washers are hardened to HRC38.42. Carbon Steel Washers are hardened to RC59.61.
Washers - Disc Spring - Carbon Steel
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093.
Washers - Disc Spring - Stainless Steel
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093.
Screws - Self Drilling - Hex Head - With Washers
With bonded neoprene washer. Galvanised for corrosion resistance.
Flat arbor shim washers with keyway groove.
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
Polycarbonate pulleys for flat belts 6mm or 6.35mm wide.
Aluminium Knurled Inserts. Gold Iridite Brass Knurled Inserts. Set Screw Locking.
Pulleys - Flat Belt - Idler - Heavy Duty
Complete with Needle Roller Bearing.
Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.
Worm Gears - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm
Match with metallic worms Module 0.80 Series 2.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worm Gears - Module 1.5 (Series 1) - Plastic and Metallic - Left Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.43 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worm Gears - Module 1.5 (Series 1) - Plastic and Metallic - Right Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.43 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worm Gears - Module 1.5 (Series 3) - Plastic and Metallic
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 6.90 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Left Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Right Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worm Gears - Module 1 (Series 2) - Plastic Gear and Metallic Worm
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Left Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.87 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.87 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worm Gears - Module 2 (Series 3) - Plastic and Metallic - Left Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.70 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worm Gears - Module 2 (Series 3) - Plastic and Metallic - Right Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.70 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worm Gears - Module 2 (Series 4) - Plastic Gear and Metallic Worm
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worms - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm
Match with metallic worms Module 0.80 Series 2.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worms - Module 1.5 (Series 1) - Plastic and Metallic - Left Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.43 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worms - Module 1.5 (Series 1) - Plastic and Metallic - Right Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.43 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worms - Module 1 (Series 1) - Plastic and Metallic - Left Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worms - Module 1 (Series 1) - Plastic and Metallic - Right Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worms - Module 1 (Series 2) - Plastic Gear and Metallic Worm
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worms - Module 2.5 (Series 1) - Plastic and Metallic - Left Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.87 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worms - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.87 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worms - Module 2 (Series 3) - Plastic and Metallic - Left Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.70 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Worms - Module 2 (Series 3) - Plastic and Metallic - Right Hand
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.70 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.Too many choices?
You have selected to see ALL categories including any of the following words: flat washers metallic and plastic
|
| |||||||||||||||||||||||||
| Select all items starting with... | |||||||||||||||||||||||||
| A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | Or use the category search | ||||||||||||||||
|
| |||||||||||||||||||||||||
