Categories for: cross blocks
Cross Blocks - Heavy Duty - One Knob One Nut
Used for connecting two round rods at 90 degrees.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Knobs have brass insert for easy turning and to prevent galling. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.
Cross Blocks - Heavy Duty - Two Knobs
Used for connecting two round rods at 90 degrees.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Knobs have brass insert for easy turning and to prevent galling. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.
Cross Blocks - Heavy Duty - Two Nuts
Used for connecting two round rods at 90 degrees.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.
Gearboxes - Cross Axis - 104 x 63 x 63
Helical or Wormwheel Gears. 15mm Bores. E40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Helical Gears and Worms : Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Worm Wheel : Aluminium Bronze (CA104 / AB2). Circlips : Steel (not plated). Bearing : Steel 2RS (Rubber seals fitted).
Gearboxes - Cross Axis - 110 x 95 x 38mm
Worm and Wormwheel box. 10.3 to 40.0Nm. 5:1 to 120:1 ratios. P45 and PF45 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
Gearboxes - Cross Axis - 130 x 110 x 46mm
Worm and Wormwheel box. 13.4 to 57.0Nm. 5:1 to 120:1 ratios. P55 and PF55 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
Gearboxes - Cross Axis - 130 x 80 x 80
Helical or Wormwheel Gears. 20mm Bores. E50 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Helical Gears and Worms : Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Worm Wheel : Aluminium Bronze (CA104 / AB2). Circlips : Steel (not plated). Bearing : Steel 2RS (Rubber seals fitted).
Gearboxes - Cross Axis - 136.5 x 111.1 x 63.5
Worm gears.
Maximum input speed 1800 RPM. Approx weight 2.7 KG (6 lb).
Gearboxes - Cross Axis - 150 x 125 x 54mm
Worm and Wormwheel box. 30.0 to 118.0Nm. 5:1 to 120:1 ratios. P60 and PF60 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
Gearboxes - Cross Axis - 150 x 96 x 96 A
Helical or Wormwheel Gears. 25mm Bores. E60 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Helical Gears and Worms : Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Worm Wheel : Aluminium Bronze (CA104 / AB2). Circlips : Steel (not plated). Bearing : Steel 2RS (Rubber seals fitted).
Gearboxes - Cross Axis - 170 x 145 x 60mm
Worm and Wormwheel box. 38.0 to 164.0Nm. 5:1 to 120:1 ratios. P70 and PF70 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
Gearboxes - Cross Axis - 18.8 x 13.5 x 12.0mm
PREM6 Series.
Gearbox Case: Aluminium 6082 T6. Gears: Steel 817M40T condition.
Gearboxes - Cross Axis - 38.9 x 31.8 x 19.1mm
Worm Gears - Precision.
Max Input : 6000 RPM. Backlash at Output : 0 Deg 30 Min. Packed with grease at assembly - temp range -32 Deg C to +146 Deg C (-25 F to 295 F).
Gearboxes - Cross Axis - 47 x 40 x 22mm
Worm and Wormwheel box. 1.4 to 2.5Nm. 5:1 to 120:1 ratios. P20 and PF20.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
Gearboxes - Cross Axis - 52.4 x 44.5 x 25.4
Worm Gears. Precision Quality - Input Speeds up to 6000 RPM.
Max Input : 6000 RPM. Backlash at Output : 0 Deg 30 Min. Packed with grease at assembly - temp range -32 Deg C to +146 Deg C (-25 F to 295 F).
Gearboxes - Cross Axis - 52 x 34 x 34
Helical or Wormwheel Gears. 6mm Bores. E20 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Helical Gears and Worms: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Worm Wheel: Aluminium Bronze (CA104 / AB2). Circlips: Steel (not plated). Bearing: Steel 2RS (Rubber seals fitted).
Gearboxes - Cross Axis - 70 x 60 x 28mm
Worm and Wormwheel box. 2.5 to 8.8Nm. 5:1 to 120:1 ratios. P30 and PF30 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
Gearboxes - Cross Axis - 77.8 x 63.5 x 34.9
Worm Gears. Precision Quality - Input Speeds up to 6000 RPM.
Max Input : 6000 RPM. Backlash at Output : 0 Deg 30 Min. Packed with grease at assembly - temp range -32 Deg C to +146 Deg C (-25 F to 295 F).
Gearboxes - Cross Axis - 78 x 48 x 48
Helical or Wormwheel Gears. 10mm Bores. E30 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Helical Gears and Worms : Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Worm Wheel : Aluminium Bronze (CA104 / AB2). Circlips : Steel (not plated). Bearing : Steel 2RS (Rubber seals fitted).
Gearboxes - Cross Axis - 85.6 x 66.7 x 34.9
Worm Gears - Commercial size 26.
Maximum input speed 1800 RPM. Approx weight 0.6 KG (20 oz).
Gearboxes - Cross Axis - 90 x 75 x 32mm
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
Slides - Linear - Cross Roller Rail
Compact, precision bearings that can support and guide high loads with high accuracy and repeatability, low friction, and low starting force.
Each consists of a pair of hardened steel ways containing 90 deg V grooves and a row of alternately crossed cylindrical rollers. Installed faced to face on smooth flat and accurately parallel, coplanar or perpendicular surfaces. Lubrication required, light grease for low speeds to continuous oil bath/mist for high speeds.
Couplings - Cross Joint - High Speed
0.3 to 6 N.m. 15000 to 42000 rpm.
Aluminium A2017 Hubs. Stainless Steel SUS304 Spacers. Hardened Steel Bearing Pins. Abrasion Resistant Polyamide Bush. SCM435 Black Coated Steel Cap Screws.Switches - Accessories - Contact Blocks/Modules
Contact blocks are modular and maybe used with 22 or 30mm operator head.
A NO or NC can be added to standard complete devices. Contact blocks are rated 10amp 600VAC.
Low cost, light weight, high energy material
Non conductive hard brittle material. Performs best at temperatures below 249 Deg C. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
For use in Cross Axis gearboxes with bores. P and PF Series.
Stainless 303 shaft. Steel keys and circlips. P-X and P-DX types suitable for P and PF type gearboxes (cross axis types).
Flywheel Rench, Allen Key Set, Socket Driver Se, 4-way cross wrench, pioin stocker, ball end pliers, side cutters, long nose pliers, flat nose pliers, pinion storage, hobby scissors and body reamer.
See main listings for sizes not shown here.
Housings - Bearing - Pillow Block - Nylon
Moulded Nylon 101 Housing. Suit miniature bearings.
Inexpensive retention of small flanged radial bearings or bushes. Standard flanged bearings snap into these bearing blocks. Not intended for precision applications. A small drop of adhesive may be required to ensure bearing remains in place.
For precise linear motion.
Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100°C ( Constant), +140°C (Maximum). For temperatures over 100°C we can supply special high temperature grease (200°C - supplied in syringe) CG2-SY.
Ball Slides and Crossed Roller Positioning Stages
Used for Gauging and Positioning Light to Medium Loads.
Spring loaded micrometer drives allow precise repeatable adjustments with low friction and zero backlash. Positioning Slides can be stacked for Multi axis applications. Preloaded positioning slides fully assemebled. Black Anodized Finish.
Complete device 2 position joystick includes operator, clip and one contact block.
Complete device 4 position joystick includes operator, clip and two contact block. Contact blocks are rated 10amp 600VAC and have finger safe screw terminals. Operators are IP65 rated. 22mm Panel Cutout.
Housings - Bearing - Pillow Block - Miniature
Aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings. Double shielded bearings to minimise contamination.
Housings - Bearing - Pillow Block - Bronze Bearing
Aluminium with 5 percent self aligning sintered bronze bearing.
Bearing: Bronze SAE 840 (oil impregnated). / Housing: Sintered Aluminium / Corrosion Resistant. Mating shaft recommendation: Min. hardening 100 HRB (Rockwell B). Max surface finish 16 RMS. Recommended shaft clearance is 0.013 - 0.038mm, using lower limit of bore tolerance. Maximum Load and Speed: The figure shown in the plain bearing data are maximums, for guidance only, and cannot be combined. The performance of a plain bearing is stated as a PV value, which is the product of a pressure and velocity.
Housings - Bearing - Pillow Block - Die Cast
Zinc Die Cast Housings with or without Sintered Bronze Bearings.
Lubricable. With or without standard sintered bronze bearings.
Housings - Bearing - Pillow Block - Needle Roller Bearing
Aluminium with 5 percent self aligning drawn cup needle roller bearing.
Bearing: Drawn cup needle roller. / Housing: Sintered Aluminium / Corrosion Resistant. Mating shaft recommendation: Min. hardening 58 HRC (Rockwell C). Max surface finish 16 RMS. Recommended shaft clearance is 0.013 - 0.038mm, using lower limit of bore tolerance.
Housings - Bearing - Pillow Block - Nylon with Ertalyte Bearing
Flanged Ertalyte Bearing in Moulded Nylon 101 Housing.
Self-Lubricating. High Performance. Electrically Insulating.
Housings - Bearing - Pillow Block - Nylon with Stainless Bearing
Moulded Nylon 101 Housing with 440C Stainless Bearing.
Bearing block: Nylon / Bearing: 440C Stainless / Insert: 52100 Chrome Steel. High Performance. Housing is Electrically Insulating. Not intended for precision applications. Inner assembly not fixed in place. Can be used as a floating assembly or fixed using conventional adhesives or circlips.
Housings - Bearing - Pillow Block - PTFE Bronze Bearing
Aluminium with 5 percent self aligning sintered bronze bearing and PTFE solid lubricant.
Bearing: Bronze PTFE impregnated. / Housing: Sintered Aluminium / Corrosion Resistant. Mating shaft recommendation: Min. hardening 100 HRB (Rockwell B). Max surface finish 16 RMS. Recommended shaft clearance is 0.013 - 0.038mm, using lower limit of bore tolerance. Maximum Load and Speed: The figure shown in the plain bearing data are maximums, for guidance only, and cannot be combined. Operating temperature minus 201 to plus 282 Degrees Celsius (minus 330 to plus 540 Degrees Farenheit).
Housings - Bearing - Pillow Block - Thermoplastic
Iglide L280 / Igus W300 Ball with Thermoplatic Body.
Maintenance Free, Lightweight, Self-Lubricating. Compensates for alignment errors. Temperature Range -40 deg C to +130 deg C. Max. Static Tensile Strength is Long Term. Info for Short Term also available.
Bearings - Spyraflo - Pillow Block - Self Aligning
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information. +/- 5% Static Alignment. Sintered aluminium housing. Corrosion Resistant. Light weight.
Bearings - Spyraflo - Pillow Block - Washdown
Electroless nickel plated aluminium housing with stainless steel coated self aligning acetal bearings.
See links at bottom of web page for more information. +/- 5% Static Alignment. Electroless nickel plated aluminium housing. Corrosion Resistant. Light weight.
Screws - Ball - 16mm Nuts - Pillow Block
Includes ball nut.
Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.
Housings - Linear - Pillow Block
Includes Bearings.
Housing: Aluminium - carbon steel and engineered polymer bearing fitted. Super Smart Ball Bushing™ Bearing fitted. Designed for use with Hard Linear Shafting (h6 Tolerance).
Housings - Linear - Pillow Block - Closed - Ceramic Coated
Approved for direct food contact in applications where animal fat or food approved lubricants are present.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. DO NOT USE WD-40 or Silcone based spray lubricants.
Housings - Linear - Twin Pillow Block
Includes Bearings.
Housing: Aluminium - carbon steel and engineered polymer bearing fitted. Super Smart Ball Bushing™ Bearing fitted. Designed for use with Hard Linear Shafting (h6 Tolerance).
A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only.
Universal Joints - Hex Bore Quick Release Needle Roller
DIN808-W Low Backlash with Sealed Bearings
Forged centre cross with hard ground ends for sealed needle bearings. 4000 RPM Max. Round bore one side. Hex bore on the quick release.
Universal Joints - Quick Release Needle Roller - Integral Shaft
DIN808-W Low Backlash with Sealed Bearings
Forged centre cross with hard ground ends for sealed needle bearings. 4000 RPM Max. Round bore both sides.
Universal Joints - Quick Release Needle Roller - Integral Shaft - Hex Bore
DIN808-W Low Backlash with Sealed Bearings
Forged centre cross with hard ground ends for sealed needle bearings. 4000 RPM Max. Integral shaft one side. Hex bore on the quick release.
Universal Joints - Quick Release Needle Roller - Round Bore
DIN808-W Low Backlash with Sealed Bearings
Forged centre cross with hard ground ends for sealed needle bearings. 4000 RPM Max. Round bore both sides.
Adjustable supports for all kinds of machinery.
Mild steel bright zinc plated. Screwdriver cross recess in base.
Linear Slide - Drylin - Accessories
Insensitive to dust and dirt.
Carriage blocks and half slide rail. Make your own custom sized assemblies. Replace blocks on carriage assemblies. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
The sealing plug is a safe, quick, leakproof and low cost method for sealing cross-drilled holes. It ensures peak performance with a comfortable safety margin even in extreme applications.
Sleeve: Stainless Steel DIN 1.4305, AISI 303. Ball: Bearing Steel, Heat Treated. Hardness: HB = 220.
Gearmotors - Basic - Hobby - 12.1mm Diameter
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
Bearings - For Cast Iron Housings
With spherical OD for use with cast iron flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request. Lubrication Hole to match Lubrication groove in housing.
Bearings - For Pressed Metal Housings
With spherical OD for use with pressed metal flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request.
ABS Plastic enclosures come complete with a 22mm operator and contact block.
Contacts are SPST at 10amps 600VAC base mounted contacts with screw terminals. Conduit knocout holes are 20mm.Too many choices?
You have selected to see ALL categories including any of the following words: cross blocks
|
| |||||||||||||||||||||||||
| Select all items starting with... | |||||||||||||||||||||||||
| A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | Or use the category search | ||||||||||||||||
|
| |||||||||||||||||||||||||
