Categories for: adhesives
Molytec, Loctite, Pacer, Dow Corning, 3M. Includes silicone sealant, gasket adhesive, canopy glue, belt conditioner and electronic tak-pak.
Mercury, ZAP, Molytec, Loctite, Pacer, Pro Seal. Cyanoacrylate adhesives for quick bonding. Products for foam Kicker, wood, metals, rubber and plastics.
ZAP, Molytec, Pacer. 5 and 30 minute. Metal filled and standard.
Versatile material for building robots because of its ability to glue well with epoxy and superglue.
Can be easily shaped by immersing in hot water and bending to your desired shape while it cools. Can be easily cut, drilled and threaded for screw fasteners. Do not use black Sintra with solar powered robots as it may get soft on hot days.
Housings - Bearing - Pillow Block - Nylon with Stainless Bearing
Moulded Nylon 101 Housing with 440C Stainless Bearing.
Bearing block: Nylon / Bearing: 440C Stainless / Insert: 52100 Chrome Steel. High Performance. Housing is Electrically Insulating. Not intended for precision applications. Inner assembly not fixed in place. Can be used as a floating assembly or fixed using conventional adhesives or circlips.
Screws - Security - Post Combi Square - Pan Head - Super Zinc
Each 200 pack comes with a Post Combination Driver Bit
Use special tool listed under Screws - Securty - Socket - Tools.
Bearings - Linear - Ball - Miniature - Super High Precision
High Precision Corrosion Resistant Miniature Linear Bearings.
High Precision Swiss Made, Accurate Guiding, Smooth Running. High Load Capacity. Tolerances --- d (+0.008 / -0.000 mm) D (+0.000 / -0.010 mm). Recommended Outer ring fitted with interferance of 1-3 Microns or retained by Circlips. Shafts (not included) should be 60-63 Rockwell C hardness with tolerances +0.000 / -0.006 mm.
Bearings - Linear - Ball - Thomson Super (Open)
For running on shafts supported by a rail along their length.
Bearings - Linear - Ball - Thomson Super Smart (Open)
For running on shafts supported by a rail along their length.
Self fusing silicone wrapping tape for emergency repairs or general protection. Seals leaks. Permanent. Self Bonding. No adhesive.
Resists Fuels, Oils, Acid, Solvent, Salt Water, Road Salt and UV Rays. Temp Range minus 50 deg C to plus 260 deg C. Insulates 8000 Volts (per unstretched layer). Tensile Strength 700psi. Lasts for years with a permanent air tight and water tight seal. Some uses include emergency radiator hose repair, insulation for radioactive areas, garden hose repair, exhaust pipe repair, electrical insulation, tool grips, sporting grips, rope ends, air duct joints, wire bundles. Areas of use include outdoor, auto, marine, workshop, motorcycle, camper, hunting, fishing, farming, plumbing, corrosive areas.
Dalchem polyester and epoxy casting resins for encapsulating display items
Note! There is a $20.00 dangerous goods charge for delivery of these items.
Dalchem polyester and epoxy laminating resins for making glass and carbon fibre
Note! There is a $20.00 dangerous goods charge for delivery of these items.
Housings - Bearing - Double Assembly - Circlip Retained
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with bearings and circlips fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
Housings - Bearing - Pillow Block - Nylon
Moulded Nylon 101 Housing. Suit miniature bearings.
Inexpensive retention of small flanged radial bearings or bushes. Standard flanged bearings snap into these bearing blocks. Not intended for precision applications. A small drop of adhesive may be required to ensure bearing remains in place.
Housings - Bearing - Single Assembly
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with a bearing fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
Housings - Bearing - Single Assembly - Circlip Retained
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with bearings and circlips fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
Low compression set, High weather resistance, Hig chemical resistance
On side has adhesive on it.
Neoprene and natural rubber gaskets for sealing doors and many other applications.
Meet NEMA 12 to NEMA 4X applications. Easy to install with self adhesive backing. Easily cut to size and shaped for many applications. Fibre backing helps to eliminate stretching and helps to maintain seal in position.
Housings - Linear - Open (Type 1)
Bearings not included.
Material: Aluminium. Adhesive may be necessary to secure bearing in housing. These lightweight but heavy duty Aluminium sets offer high accuracy. They consist of a corrosion resistant, highly rigid Aluminium housing. For use with open linear bearings with OD matching the housing bore dimension D.
Housings - Linear - Open (Type 2)
Bearings not included.
Material: Aluminium. Adhesive may be necessary to secure bearing in housing. These lightweight but heavy duty Aluminium sets offer high accuracy. They consist of a corrosion resistant, highly rigid Aluminium housing. For use with open linear bearings with OD matching the housing bore dimension D.
Bearings not included.
NOTE: You may need to use adhesive to hold the bearing securely in place on the 'D' dimension. These lightweight but heavy duty Aluminium sets offer high accuracy. They consist of a corrosion resistant, highly rigid Aluminium housing. The units can be attached to any surface to offer support in any direction. For use with closed linear bearings with OD matching the housing bore dimension D.
Leadscrew Nut Flanges for Acme Supernuts
Flanges for Acme leadscrew thread supernuts metric and imperial
MATERIAL - Aluminum 6062-T6. These flanges are screwed onto the outer thread of the red leadscrew nuts. This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved.
Leadscrew Nuts - Imperial - Supernuts - Acme
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
Leadscrew Nuts - Metric - Supernuts - Acme
Acme Leadscrew Nuts - Use with Acme Leadscrew Thread and flanges for mounting
Bushes - Aluminium - Frelon Lined - Flanged
Self lubricating - Replaces oilite or plastic bearings.
SLIP FIT: Housing bore should be OD +0.050/+0.075 - lock in place with retaining compound or epoxy. PRESS FIT: Housing bore should be OD -0.000/+0.010. Use freezing method for press fit assembly - freeze bearing to -18 Deg C for 30 minutes. Body: Aluminium. Lining: Frelon.
High impact light weight carbon fibre for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish. Items marked as Low Grade may have tolerance variations up to 0.2mm.
Tube - Rectangular - Carbon Fibre
High impact light weight carbon fibre hollow tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish.
High impact light weight carbon fibre hollow tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish. Items marked as Low Grade may have tolerance variations up to 0.2mm.
Tube - Square - Carbon Fibre - Round Hole
High impact light weight carbon fibre tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish. Items marked as Low Grade may have tolerance variations up to 0.2mm.
Tube - Square - Carbon Fibre - Square Hole
High impact light weight carbon fibre tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish. Items marked as Low Grade may have tolerance variations up to 0.2mm.
Inserts - Thread Repair - Helicoil
Replacement helicoil inserts for after you have purchased a starter kit or tools separately.
Stainless 18-8 inserts with a hardness of RC43-50 and tensile strength above 200,000 PSI. Metric and Imperial available. Screw locking inserts have a series of straight segments to provide self-locking torque on the bolt, eliminating a need for other threadlocking methods.
Inserts - Thread Repair - Recoil
Recoil inserts are screwed directly into an enlarged tapped hole. Replacement inserts for your kit.
Stainless inserts. Replacement Individual Inserts - Require full kit to obtain correct tap. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
Housings - Linear - Pillow Block
Includes Bearings.
Housing: Aluminium - carbon steel and engineered polymer bearing fitted. Super Smart Ball Bushing™ Bearing fitted. Designed for use with Hard Linear Shafting (h6 Tolerance).
Housings - Linear - Twin Pillow Block
Includes Bearings.
Housing: Aluminium - carbon steel and engineered polymer bearing fitted. Super Smart Ball Bushing™ Bearing fitted. Designed for use with Hard Linear Shafting (h6 Tolerance).
Designed to fit standard supermarket trolley or industrial trolley wheel yokes.
Quiet operation. Non marking. Smooth running.
Screws - Machine - PEEK - Pan Head
PEEK is a super-engineering thermoplastic used for its special physical and chemical characteristics. Excellent resistance to chemicals, water, abrasion, shock, fatigue, radiation, heat, etc. PEEK is registered trademark of Vitre™.
Excellent chemical resistance, impenetrable by most chemicals with the exception of concentrated sulphuric acid. Excellent thermal and water resistance; maintains high heat-resistance strength. Excellent abrasion, shock and fatigue resistance. Excellent radiation resistance and electrical properties. Heat-resistant temperature: 180 Degrees Celcius (UL approved temperature). Excellent flame-resistance cleared by UL standard 94V-0. Useful for hot-water pumps, chemical pumps, chemical-resistant applications such as FPD (Flat Panel Display) and semiconductor production equipment/devices, printed circuit board etching devices, metal plating equipment and chemical plants. Use with a nut to compensate for thread moulding pitch errors. When a nut is not used, it is recommended that the overlap of mating screw threads be shorter than 20mm. For further information on the special properties of plastic screws and cautions concerning their use, please contact sales.
Screws - Machine - PEEK - Countersunk Head
Material: Polyetheretherketone - Super-engineering thermoplastic, excellent for its special physical and chemical characteristics.
Excellent chemical reistance, impenetrable by most chemicals with the exception of concentrated sulphuric acid. Excellent radiation resistance and electrical properties. Excellent thermal and water resistance; maintains high heat-resistnace strength. Excellent abrasion, shock and fatigue resistance. Excellent flame-resistance. Heat resistant temp 180 Deg C. Useful in hot-water pumps, chemical pumps, electronic field applications: transformers and computer machinery. May be used in vacuum chamber applications in clean rooms, Flat Panel Displays, Semiconductor production equipment and devices. Use with a nut to compensate for thread moulding pitch errors. When a nut is not used, it is recommended that the overlap of mating screw threads to be shorter then 20mm.
Leadscrews - Imperial - Acme - Alloy Steel
Acme Leadscrew Thread - Use with Acme Supernuts
Alloy steel heat treated to RC 56-60.
Acme Leadscrew Thread - Use with Acme Supernuts
Circlips - External - Grooveless
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA.
Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring.
Couplings - BoWex - Tooth Driven - Sintered Steel
Sintered steel hubs and nylon centre sleeve
Operating temp range -25 Deg C to 100 Deg C. Maintenance free. Compensates for axial, radial and angular shaft displacement. Easy to assemble. Alternative bore and keyway sizes can be supplied on approx 5 weeks delivery. Please contact our sales staff to arrange this.
Couplings - Crowned Tooth Gear - Complete
Steel hubs with Moulded Nylon Sleeve.
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1 Degree Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Couplings - Crowned Tooth Gear - Hubs Only
Match with sleeves from the sleeves category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1 Degree Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Couplings - Crowned Tooth Gear - Sleeve Only
Match with hubs from the hubs category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1 Degree Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
630B - 630C PB SuperTorque Kavo Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
640B - 640C PB SuperTorque Kavo Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Cross Blocks - Heavy Duty - One Knob One Nut
Used for connecting two round rods at 90 degrees.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Knobs have brass insert for easy turning and to prevent galling. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.
Cross Blocks - Heavy Duty - Two Knobs
Used for connecting two round rods at 90 degrees.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Knobs have brass insert for easy turning and to prevent galling. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.
Cross Blocks - Heavy Duty - Two Nuts
Used for connecting two round rods at 90 degrees.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.Too many choices?
You have selected to see ALL categories including any of the following words: adhesives
Click here to see ONLY THE MOST POPULAR categories including any of the following words: adhesives
|
| |||||||||||||||||||||||||
| Select all items starting with... | |||||||||||||||||||||||||
| A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | Or use the category search | ||||||||||||||||
|
| |||||||||||||||||||||||||
